JL Audio Stealthbox SB-T-4RNR2/10W3v3/GA Handleiding

JL Audio Niet gecategoriseerd Stealthbox SB-T-4RNR2/10W3v3/GA

Lees hieronder de 📖 handleiding in het Nederlandse voor JL Audio Stealthbox SB-T-4RNR2/10W3v3/GA (3 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 20 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/3

➔

Stealthbox®

I N S T A L L A T I O N G U I D E

SB - T-4RNR2/10 W v 2 , J L AU D I O , In c 2 0 0 3 Sh e e t S K U # 0 1 1 1 8 1 Re v i s io n 0 1 / 1 3 / 2 0 0 4

Pag e 1

for the

SB-T-4RNR2/10W3v2

(‘02-Up Toyota 4-Runner SR-5, Sport

Edition & Limited)

This Stealthbox is a product which

requires professional installation skills and

tools.

Please read this installation guide thor-

oughly before beginning the project. It

will guide you step by step through the

installation. Several of the steps in this

process may require two people to

accomplish.

It is absolutely vital that the enclosure

be properly mounted to the vehicle

according to these instructions. Failure

to mount the enclosure properly pres-

ents two problems: 1) The sub-bass

performance will suffer due to the

movement of the enclosure caused by

the force exerted by the woofer(s) and

2) A loose enclosure presents a serious

safety hazard in the event of a collision

or sudden deceleration.

Please enjoy your JL Audio Stealthbox

responsibly.

STEP 1:

Clean out all contents. Remove the

cargo cover and carpet mat.

STEP 2: Remove the rear sill plate(A) and side

storage door(B).

With the sill plate removed, pull and fold over the car-

pet out of the corner(circled).

On Limited Edition interiors, remove the plastic tray.

The flooring carpet will not fit flush aginst the

Stealthbox, once isntalled.

STEP 3:

Place the supplied wax square into

position.

The middle of wax square (X marks the

spot) needs to be 3.5” back from the wheel

well and from the side panel.2.5”

Remove the adhesive protective paper from

the under side of the wax square and stick to

the floor.

STEP 4: Thread in the supplied tsocket cup set

screw, leaving about a 1/2” out of the Stealthbox.

Make sure that the socket cup end is exposed.

Place the Stealthbox into position and press down

firmly.

STEP 5: With the Stealthbox removed and wax

square still in position, use a 1/2” drill bit to drill out

the marked location.

After hole is drilled, remove the wax square.

STEP 6: Place and line up the hole, of one of the

supplied black metal plates to the 1/2” drilled hole

from STEP 5.

Use tape to temporary secure the metal plate into

position.

START

HERE

Continued on Next Page ➔

w w w . j l a u d i o . c o m

➔

STEP

2.5”

3.5”

➔

➔ ➔

STEP 7: Place the carpet that was pulled out of

the corner in , back into position.STEP 2

Cut out an access hole in the carpet, that is lined up

and position above the black metal plate’s hole, from

STEP 6.

STEP 8B: When the knob is unlocked correctly,

the exposed knob will pull away from the side panel,

but is still attached to the cleat assembly.

With the cleat unlocked, remove from the side

panel.

Cont.

From

Page

Continued on Next Page ➔

➔

STEP 8: Remove the access door( ) and cargoA

net cleat(B).

Follow STEPS 8A and 8B to properly remove

the cargo net cleat.

STEP 9: Run the speaker wire to the Stealthbox’s

location.

Check for proper operation of the woofer and

attach speaker wire to terminal.

Before placing the Stealthbox back into location,

back out the threaded rod to expose about 1”.

STEP 8A: This is how the cleat looks when

installed into the side panel. (side panel not seen)

Grab a hold of the exposed knob’s edge with your

finger nails and pull out. It should not require a lot of

force. *Do not force it.*

SB - T-4 RN R2 / 1 0 W v 2 , J L AUD IO, I n c 2 0 0 3 Sh e e t S K U # 0 1 1 1 8 1 Re v i s io n 0 1 / 1 3 /2 0 0 4

Pag e 2

w w w . j l a u d i o . c o m

➔

STEP 10: With the Stealthbox wired up and in

location(with socket cup set screw placed through the car-

pet, metal plate and floor).

Place a supplied flat washer onto the supplied bolt. Place the

bolt assembly through the upper mounting support bracket

of the Stealthbox and the factory plastic side panel.

On the back side of the plastic side panel, place a supplied

flat washer, lock washer and then thread supplied nut onto

the bolt assembly .(through the removed excess door loca-

tion.)

Using a 9/16” open end wrench to hold the nut behind the

plastic panel.Tighten the exposed bolt with a 9/16” socket.

➔

Specifications:

Enclosure Type: Acoustical Suspension (Sealed)

Driver Type: 10W3v2-D2

Nominal Impedance: 4Ω

Cont. Power Handling: 300Watts

JL Audio recommends using a high quality amplifier such as the JL Audio 250/1. The diagram below shows the recommended

crossover, infrasonic filter and equalizer settings for the 250/1 when being used to power your Stealthbox®.

Supplied Hardware:

2) 3/8” Split Lock Washers

2) 3/8” Flat Washers

2) 3/8” x 1-1/4” Fender

2) 3/8”-16 x 2-1/4” hex

1) 1/4”-20 Install Bolt

1) 3/8”-16 x 2-1/4” Socket Cup Set Screw

1) 3” x 3” Wax Square

2) 3/8”-16 Hex Nut

10369 N. Commerce Pkwy, Miramar, Florida 33025-392 Phone: 954.443.1100 Fax: 954.443.1111

JL AUDIO 250/1

monoblock subwoofer amplifier

Amplifier Input Section

Input Sens.Input Voltage

Low/High

Left Ch. Right Ch.

Signal Sensing

Off/On

Output Mode

Full-Range/Low-Pass/High-Pass

Left Ch. Right Ch.

Amp LP Filter

Mode/Slope

Off/12dB/24dB

Filter Freq. (Hz)

Bass Control

LF Boost (dB)

Off/30Hz

Infrasonic Filter

+1 +13

+10

Preamp Output Section

+12VDC Ground Remote

The JL Audio 250/1 is a very versatile audio component. Please consult the owner’s manual for detailed information

about installing and tuning this amplifier.

➔ ➔ ➔

STEP 11: Take the other supplied black metal

plate, lock washer, flat washer and nut to the under

side of vehicle.

STEP 12: Place the other black metal support

plate, flat washer, lock washer and thread the nut

onto the threaded rod. Use a 9/16” socket and long

extension to fully secure the mounting assembly.

If the socket cup set screw is not protruding far

enough, loosen.

STEP 13: Replace the carpet and any other con-

tents back into cargo area.

For cosmetics, we folded the corner of the carpet

back under it self. We do not recommend that you

cut this carpet.

➔

SB - T- 4 RN R2 / 1 0 W v 2 , J L AU DI O, I n c 2 0 0 3 Sh e e t S K U # 0 1 1 1 8 1 Re v i s io n 0 1 / 1 3 /2 0 0 4Pag e 3

w w w . j l a u d i o . c o m

Mid/High Frequency Driver Information:

CONGRATULATIONS!

INSTALL COMPLETE.

TR690-TXI

VR650-CXI

Front Location Driver Size:

6”x9” with separated tweeter

Applicable JL Audio Products:

TR690-TXi & VR690-CXi, does require

spacer/mounting rings.

Rear Location Driver Size:

6 3/4”

Applicable JL Audio Products:

TR650-CXi,VR650-CXi & XR650-CXi,

does require spacer/mounting rings.

Cont.

From

Page

Product specificaties

Merk:	JL Audio
Categorie:	Niet gecategoriseerd
Model:	Stealthbox SB-T-4RNR2/10W3v3/GA

Heb je hulp nodig?

Als je hulp nodig hebt met JL Audio Stealthbox SB-T-4RNR2/10W3v3/GA stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd JL Audio

JL Audio Stealthbox SB-F-ESCP/10W1v3 Handleiding

15 November 2024

JL Audio Stealthbox SB-J-JL4DDRV/10TW1-2 Handleiding

15 November 2024

JL Audio MediaMaster 55-HR Handleiding

7 Augustus 2024

JL Audio MediaMaster 55 Handleiding

7 Augustus 2024

JL Audio MBT-RXv2 Handleiding

9 Juli 2024

JL Audio MBT-CRXv3 Handleiding

9 Juli 2024

JL Audio Stealthbox SBX-F-MAVG1/10TW1 Handleiding

10 Juni 2024

JL Audio Stealthbox SBX-T-TACDCG3/10TW3 Handleiding

10 Juni 2024

JL Audio MediaMaster MM105-HR Handleiding

11 Maart 2024

JL Audio JLINK RX Handleiding

8 Januari 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Kolcraft MLB Chicago Cubs Handleiding

26 November 2024

Kolcraft MLB New York Yankees Handleiding

26 November 2024

Kolcraft MLB San Francisco Giants Handleiding

26 November 2024

Kolcraft MLB St. Louis Cardinals Handleiding

26 November 2024

Nedis POCO106 Handleiding

26 November 2024

Nedis BTSM1GY Handleiding

26 November 2024

Turbosound TPOLEAJ-01 Handleiding

26 November 2024

Turbosound TSTAND-01 Handleiding

26 November 2024

IFM TAD981 Handleiding

26 November 2024

IFM TAD961 Handleiding

26 November 2024