JL Audio Stealthbox SB-N-350/10W3v3 Handleiding

JL Audio Niet gecategoriseerd Stealthbox SB-N-350/10W3v3

Lees hieronder de ๐Ÿ“– handleiding in het Nederlandse voor JL Audio Stealthbox SB-N-350/10W3v3 (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 56 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
โž”
โž”
โž”
โž”
Stealthboxยฎ
I N S T A L L A T I O N G U I D E
SB - N - 3 5 0 / 1 0 W 3 v 2 , J L AU D I O , I n c 2 0 0 4 Sh e e t S K U # 0 1 1 1 8 7 Rev i s i o n 2 / 1 1 / 2 0 0 4Pag e 1
for the
SB-N-350/10W3v2
(2003-Up 350Z, Will not fit the 350z
Roadster, Infiniti G35 Coupe & Sedans)
This Stealthbox is a product which
requires professional installation skills and
tools.
Please read this installation guide thor-
oughly before beginning the project. It
will guide you step by step through the
installation. Several of the steps in this
process may require two people to
accomplish.
It is absolutely vital that the enclosure
be properly mounted to the vehicle
according to these instructions. Failure
to mount the enclosure properly pres-
ents two problems: 1) The sub-bass
performance will suffer due to the
movement of the enclosure caused by
the force exerted by the woofer(s) and
2) A loose enclosure presents a serious
safety hazard in the event of a collision
or sudden deceleration.
Please enjoy your JL Audio Stealthbox
responsibly.
STEP 1:
Remove all contents from center
console, rear cargo area, rear glove box com-
partments, lastly slide and tilt the seats to the
front of the car.
STEP 3:
Remove the driverโ€™s side and pas-
sengerโ€™s side door sill panels.
*Carefully pulling directly upward.*
STEP 2:
Remove the driverโ€™s side and pas-
sengerโ€™s side rear interior cargo quarter pan-
els.
STEP 4:
Remove the Philip head screws, that
are found on both diverโ€™s side and passen-
gerโ€™s side of the console.
STEP 5:
Remove the two Philip head screws
that have been exposed by the removal of
the ashtray.
START
HERE
Continued on Next Page โž”
w w w . j l a u d i o . c o m
โž”
โž”
STEP 6: Loosen the shifter trim panel by pulling
directly up. Pull the panel away from the console.
Manual transmission shifter shown in picture, auto-
matic shifter removal maybe slightly different, then
shown.
*Careful not to damage the shifter or
scratch the dash panel. *
โž” โž”
โž”โž”โž”
STEP 10: Lift at the rear of the console and care-
fully pull unit over the emergency hand brake arm.
Cont.
From
Previous
Page
Continued on Next Page โž”
โž”
STEP 7: Disconnect the white wiring plug at the
rear of the A/C controls.
STEP 11: Disconnect the wiring harness at the
plug located under the center console.
โž”
STEP 12: Carefully guide the shifter boot trim
panel through the front opening in the console.This
will allow for full removal of the center console.
*Careful not to damage the shifter boot or
scratch the dash panel. *
STEP 13: Remove the center console, out of the
vehcile.
STEP 8: With the shifter trim panel moved to
one side. Remove the pair of Philip head screws at
the front edge of the console.
STEP 9: Engage the emergency brake, by pulling
up on the handle.
SB - N - 3 5 0 / 1 0 W 3 v 2 , JL AUD I O , I n c 2 0 0 4 Sh e e t S K U # 0 1 1 1 8 7 Re v i s i o n 2 / 1 1 / 2 0 0 4Pag e 2
w w w . j l a u d i o . c o m
STEP 14: Remove the rear bulkhead front panel,
by carefully pulling towards the front of the vehcile
around the glove box.
โž” โž”
โž” โž” โž”
STEP 18: Pull back the carpet in the front section
of the cargo area to reveal the metal floor.
Remove the child seat anchor hooks, reinstall factory
bolts without hook.
Locate the existing holes(behind the driverโ€™s side
and passengerโ€™s side seat), to be used to mount the
Stealthbox. Identified by the white circle.
Cont.
From
Previous
Page
Continued on Next Page โž”
โž”
STEP 16: Remove the pair of 10mm head bolts at
the rear of the glove box.
STEP 19: Cut the carpet to create a flap that can
be folded to allow access to the mounting holes.
โž”
STEP 20: If the vehicle is so equipped, fold back
floor mat as shown to access the mounting bolts.
STEP 22: At this time, attach the speaker wire
from the amp to the Stealthboxโ€™s terminal.
*Check for proper operation of the
woofers.*
STEP 17: Remove the numerous 10mm head
bolts securing the front edge of the glove box liner.
SB - N - 3 5 0 / 1 0 W 3 v 2 , JL AU D I O, I n c 2 0 0 4 Sh e e t S K U # 0 1 1 1 8 7 Re v i s i o n 2 / 1 1 / 2 0 0 4 Pag e 3
w w w . j l a u d i o . c o m
STEP 15:
Remove the pair of Philip head
screws securing the passenger side glove boxโ€™s
door latch.
Repeat this STEP for the driverโ€™s side, if
equipped with the glove box. Remove the fac-
tory woofer on the driverโ€™s side, if equipped.
STEP 21: Thread in the supplied pair of socket
cup set screws. Leaving about 1.5โ€ exposed.
โž”
โž”
โž”


Product specificaties

Merk: JL Audio
Categorie: Niet gecategoriseerd
Model: Stealthbox SB-N-350/10W3v3

Heb je hulp nodig?

Als je hulp nodig hebt met JL Audio Stealthbox SB-N-350/10W3v3 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd JL Audio

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd