JL Audio Stealthbox SB-H-RIDGLNE/10W3v3/GA Handleiding

JL Audio Niet gecategoriseerd Stealthbox SB-H-RIDGLNE/10W3v3/GA

Lees hieronder de 📖 handleiding in het Nederlandse voor JL Audio Stealthbox SB-H-RIDGLNE/10W3v3/GA (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 21 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
INSTALLATION
D I F F I C U L T Y :
I N S T A L L A T I O N G U I D E
for the
SB-H-RIDGLNE/10W3v3
SKU# 94097 & 94275
2006 - 2014 Honda Ridgeline
Thank you for choosing a JL Audio Stealthbox® for your automotive sound system.
With proper installation, your new vehicle-specific enclosed subwoofer system
will deliver years of listening pleasure.
We strongly recommend that you have your new Stealthbox
® installed by your authorized
JL Audio dealer. The installation professionals employed by your dealer have the necessary
tools and experience to disassemble and reassemble your vehicle properly. Also, keep in
mind that your warranty coverage extends to 2 year if your system is installed or approved
by your authorized JL Audio dealer. If you prefer to perform your own installation,
please read this installation guide completely before beginning the process.
If you choose to perform the installation yourself, it is absolutely vital that
the Stealthbox ® be properly mounted to the vehicle according to these
instructions. Failure to mount the enclosure properly presents two problems:
1) The sub-bass performance will suffer due to the movement of the enclosure
caused by the force exerted by the woofer(s).
2) A loose enclosure presents a serious safety hazard in the event of a collision
or sudden deceleration.
S T E P 1
Remove any contents from rear seating area. Flip and lock
the rear seating in the up position.
Continued on Next Page
S T E P 2
Place the supplied wax square into place.
16-1/2" from the door sill and 4-3/4" from the bulk head, as in
the picture.
S T E P 3
Thread in the supplied socket cup set screw into the
threaded insert, located on the bottom side of the
Stealthbo. Leaving 1/4" exposed.
SB-H-RIDGLNE/10W3v3_ 011214
25
OUT
OF
161/2"
43/4"
SB-H-RIDGLNE/10W3v3_ 011214
C O N G R A T U L A T I O N S
You have completed the installation for this model!
Please refer to the Power Recommendation section for an
amplifier recommendation and basic set-up help.
S T E P 6
From under the vehicle, place the supplied fender washer,
flat washer, lock washer and then hex nut onto the protrud-
ing socket cup set screw. Secure tightly with a 14mm socket,
long extension and rachet.
Note: For added protection it is recommended that
you apply a bead of silicone between the vehicle and
the fender washer. After the bolt assembly is tightly
secured, it is also recommended that vehicle under-
coating material is applied to the exposed assembly.
S T E P 5
(A) Loosen the socket cup set screw to expose 1-1/2-inch.
Place the enclosure into place, carefully guiding the socket
cup set screw through the drilled hole. .
(B) Run speaker wire from the amplifier location to the
Stealthbox® and attach to the terminal
Double check the woofer for proper operation.
S T E P 4
A Position the Stealthbox® into place and press firmly
down. This is to make an impression onto the wax square.
Remove the Stealthbo.
B With a 1/2" drill bit or StepBit/Unibit® and drill. Drill at the
impression on the wax square, through the metal floor to the
outside.
(C) Remove the wax square.
Page 2 • JL Audio, Inc 2016
All specifications are subject to change without notice.JL Audio®” and the JL Audio logo,Stealthbox” and the Stealthbox logo are registered
trademarks of JL Audio, Inc. Ahead of the Curve and its respective logo is a trademark of JL Audio, Inc.
JLA-SKU# 011214 09.20.2016 • Printed in USA • ©2016 JL Audio, Inc.
For more detailed information please visit us online at www.jlaudio.com.
(954) 443-1100
w w w . j l a u d i o . c o m
1 0 3 6 9 N O R T H C O M M E R C E P A R K W A Y M I R A M A R , F L O R I D A 3 3 0 2 5 U S A
I N C L U D E D H A R D W A R E
(1) 3/8-inch - 16 Hex Nut 3-inch x 3-inch Wax Square(1)
(1) 3/8-inch x 3/4-inch USS Flat Washer 3/8-inch - 16 x 2-1/4-inch Socket Cup Screw(1)
(1) 3/8-inch x 1-1/4-inch Fender Washer
(1) 3/8-inch Lock Washer
S P E C I F I C A T I O N S
Enclosure Type: Acoustic Suspension (sealed)
Driver Type: 10W3v3-2
Nominal Impedance: 2 ohms
Continuous Power Handling: 500 Watts
P O W E R R E C O M M E N D A T I O N
JL Audio recommends using a high quality amplifier such as the JL Audio XD300/1v2. The diagram below shows
the recommended crossover settings for the XD300/1v2 when being used to power your Stealthbox ®.
The JL Audio XD300/1v2 is a very versatile audio component. Please consult the owners manual for even more
detailed information about installing and tuning this amplifier.
M I D / H I G H F R E Q U E N C Y D R I V E R F I T M E N T
A variety of JL Audio coaxial and component systems will fit in the factory speaker locations of you vehicle.
Front Speaker Size / Location: 6.5-inch / Front Doors
Fits JL Audio Models: TR650-CXi, TR650-CSi, C2-650x, C2-650
C3-650, C5-650x, C5-650, & ZR650-CSi
Rear Speaker Size / Location: 6.5-inch / Rear Deck
Fits JL Audio Models: TR650-CXi, TR650-CSi, C2-650x, C2-650
C3-650, C5-650x, C5-650, & ZR650-CSi


Product specificaties

Merk: JL Audio
Categorie: Niet gecategoriseerd
Model: Stealthbox SB-H-RIDGLNE/10W3v3/GA

Heb je hulp nodig?

Als je hulp nodig hebt met JL Audio Stealthbox SB-H-RIDGLNE/10W3v3/GA stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd JL Audio

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd