JL Audio Stealthbox SB-H-ELMNT/10W3v3/BK Handleiding

JL Audio Niet gecategoriseerd Stealthbox SB-H-ELMNT/10W3v3/BK

Lees hieronder de 📖 handleiding in het Nederlandse voor JL Audio Stealthbox SB-H-ELMNT/10W3v3/BK (3 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 19 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/3

➔

Stealthbox®

I N S T A L L A T I O N G U I D E

SB - H - E L M N T / 10 W 3 v2 / B K, J L AU D I O , In c 2 0 0 3 Sh e e t SKU # 0 1 1 1 8 3 Re v i s i o n 0 1 /1 5 / 2 0 0 4 Pag e 1

for the

SB-H-ELMNT/10W3v2/BK

(2003-Up Honda Element)

This Stealthbox is a product which

requires professional installation skills and

tools.

Please read this installation guide thor-

oughly before beginning the project. It

will guide you step by step through the

installation. Several of the steps in this

process may require two people to

accomplish.

It is absolutely vital that the enclosure

be properly mounted to the vehicle

according to these instructions. Failure

to mount the enclosure properly pres-

ents two problems: 1) The sub-bass

performance will suffer due to the

movement of the enclosure caused by

the force exerted by the woofer(s) and

2) A loose enclosure presents a serious

safety hazard in the event of a collision

or sudden deceleration.

Please enjoy your JL Audio Stealthbox

responsibly.

STEP 1:

Remove the front passenger’s plas-

tic seat rail cover, located under and rear of

the seat. Remove the rear mounting bolts,

using a 14mm socket.

STEP 2:

With a 14mm socket, remove the

front mounting bolts and tilt the seat to the

back.

There will be enough slack in the wire, so you

do not have to disconnect it.

STEP 3:

Remove the OEM plastic woofer

cover, by pulling out plastic push clips that are

located on each side.

STEP 4:

With a 10mm socket, remove the

four bolts (two on each side) that secure the

OEM woofer enclosure to the under dash.

STEP 5:

On the driver’s side, disconnect the

gray plug.

STEP 6:

Locate the bracket that is mounted

to the floor with a pair of bolts. Use the mid-

dle non-used hole as a drilling guide.

With a1/2” drill bit, drill through floor.

START

HERE

Continued on Next Page ➔

w w w . j l a u d i o . c o m

➔

➔ ➔

STEP 7: Mount the supplied L-bracket to the

driver’s side upper OEM woofer enclosure’s mount-

ing bolt hole (from STEP 4).Using the supplied

1/4” lock washer and 1/4” flat washer. Apply to the

factory moutning bolt that was removed from

STEP 4.

Using a 7/16” socket, securely tighten the bolt

assembly.

STEP 10: Place the Stealthbox into location.

Using the socket cup set screw as guide and place

through the drilled hole from STEP 6.

Cont.

From

Page

Continued on Next Page ➔

➔

STEP 8: Thread in the supplied socket cup set

screw into the Stealthbox, leaving about 1 3/4”

exposed. Make sure that the slotted end of the

threaded rod is exposed. Place the supplied spacer

onto socket cup screw.

Use a piece of tape to hold the spacer onto the

threaded rod.You can take off the tape, once the

Stealthbox is in lcoation.

STEP 11: While second person is holding the

Stealthbox into position (inside of vehicle). Place flat

washer, lock washer and nut onto the exposed

threaded rod and secure.

If the socket cup set screw does not have enough

length, back out the socket cup set screw from

inside of the Stealthbox.

Use silicon to weather proof the bolt assembly.

STEP 12: Use the supplied bolt, lock washer and

flat washer to secure driver’s side of the Stealthbox

to the L-bracket that was mounted in STEP 7.

STEP 9: Run speaker wire to the Stealthbox

location and attach to terminal.

*Check the woofer for proper operation.*

SB - H - E L M N T / 10 W 3 v2 / B K, J L AUD IO, I n c 2 0 0 3 Sh e e t SKU # 0 1 1 1 8 3 Re v i s i o n 0 1 / 1 5 / 2 0 0 4Pag e 2

w w w . j l a u d i o . c o m

➔

Specifications:

Enclosure Type: Acoustical Suspension (sealed)

Driver Type: 10W3v2-D2

Nominal Impedance: 4Ω

Cont. Power Handling: 300Watts

JL Audio recommends using a high quality amplifier such as the JLAudio 250/1. The diagram below shows the recommended

crossover, infrasonic filter and equalizer settings for the 250/1 when being used to power your Stealthbox®.

Included Hardware:

3) 1/4” Flat Washers

2) 1/4-20 x 1-1/2” Bolts

1) 3/8” Split Lock Washers

1) 3/8” Flat Washer

2) 1/4” Lock Washer

1) 3/8” x 1-1/4” Fender Washer

1) 3/8”-16 x 2-1/4” Socket Cup Set Screws

1) 3/8”(L)x3/4”(OD)x3/8”(ID) Spacer

1) 1/4”-20 Hex Nut

1) L-Bracket

1) 3/8”-16 Hex Nut

4) #6-32x1” Pan Head

10369 N. Commerce Pkwy, Miramar, Florida 33025-392 Phone: 954.443.1100 Fax: 954.443.1111

JL AUDIO 250/1

monoblock subwoofer amplifier

Amplifier Input Section

Input Sens.Input Voltage

Low/High

Left Ch. Right Ch.

Signal Sensing

Off/On

Output Mode

Full-Range/Low-Pass/High-Pass

Left Ch. Right Ch.

Amp LP Filter

Mode/Slope

Off/12dB/24dB

Filter Freq. (Hz)

Bass Control

LF Boost (dB)

Off/30Hz

Infrasonic Filter

+1 +13

+10

Preamp Output Section

+12VDC Ground Remote

The JL Audio 250/1 is a very versatile audio component. Please consult the owner’s manual for detailed information

about installing and tuning this amplifier.

➔

STEP 13: Mount the supplied carpeted side panels

with the four supplied Phillips screws.

STEP 14: Place the front passenger side seat

back into place and secure(STEPS 1 & 2).

*Don’t forget the plastic rail cover*

➔

SB - H - E L M N T / 10 W 3 v2 / B K, J L AUD I O , I n c 2 00 3 S h e e t S K U # 0 1 1 1 8 3 R e v i sio n 0 1 / 1 5 / 2 0 0 4Pag e 3

w w w . j l a u d i o . c o m

Mid/High Frequency Driver Information:

CONGRATULATIONS!

INSTALL COMPLETE.

VR600-CSi

TR600-CXi

Front Location Driver Size:

6.0”

Applicable JL Audio Products:

VR600-CSi

Rear Location Driver Size:

6.0”

Applicable JL Audio Products:

VR600-CXi,TR600-CXi

Cont.

From

Page

Product specificaties

Merk:	JL Audio
Categorie:	Niet gecategoriseerd
Model:	Stealthbox SB-H-ELMNT/10W3v3/BK

Heb je hulp nodig?

Als je hulp nodig hebt met JL Audio Stealthbox SB-H-ELMNT/10W3v3/BK stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd JL Audio

JL Audio Stealthbox SB-F-ESCP/10W1v3 Handleiding

15 November 2024

JL Audio Stealthbox SB-J-JL4DDRV/10TW1-2 Handleiding

15 November 2024

JL Audio MediaMaster 55-HR Handleiding

7 Augustus 2024

JL Audio MediaMaster 55 Handleiding

7 Augustus 2024

JL Audio MBT-RXv2 Handleiding

9 Juli 2024

JL Audio MBT-CRXv3 Handleiding

9 Juli 2024

JL Audio Stealthbox SBX-F-MAVG1/10TW1 Handleiding

10 Juni 2024

JL Audio Stealthbox SBX-T-TACDCG3/10TW3 Handleiding

10 Juni 2024

JL Audio MediaMaster MM105-HR Handleiding

11 Maart 2024

JL Audio JLINK RX Handleiding

8 Januari 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Kolcraft MLB Chicago Cubs Handleiding

26 November 2024

Kolcraft MLB New York Yankees Handleiding

26 November 2024

Kolcraft MLB San Francisco Giants Handleiding

26 November 2024

Kolcraft MLB St. Louis Cardinals Handleiding

26 November 2024

Nedis POCO106 Handleiding

26 November 2024

Nedis BTSM1GY Handleiding

26 November 2024

Turbosound TPOLEAJ-01 Handleiding

26 November 2024

Turbosound TSTAND-01 Handleiding

26 November 2024

IFM TAD981 Handleiding

26 November 2024

IFM TAD961 Handleiding

26 November 2024