JL Audio Stealthbox SB-F-SUPRCNSL/10W3v3 Handleiding

JL Audio Niet gecategoriseerd Stealthbox SB-F-SUPRCNSL/10W3v3

Lees hieronder de 📖 handleiding in het Nederlandse voor JL Audio Stealthbox SB-F-SUPRCNSL/10W3v3 (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 31 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

➔

Stealthbox®

I N S T A L L A T I O N G U I D E

SB- F - S U P R C N S L / 1 0 W 3 V2 , J L AU D I O , I n c 2 0 0 5 Sh e e t S K U # 0 1 1 1 4 9 R e v i s io n 8 / 4 / 2 0 0 5 Pag e 1

for the

SB-F-SUPRCNSL/10W3v2

(‘98-Up Ford SuperDuty

250,350,450,550 & 650

‘00-Up Excursion)

This Stealthbox is a product which

requires professional installation skills and

tools.

Please read this installation guide thor-

oughly before beginning the project. It

will guide you step by step through the

installation. Several of the steps in this

process may require two people to

accomplish.

It is absolutely vital that the enclosure

be properly mounted to the vehicle

according to these instructions. Failure

to mount the enclosure properly pres-

ents two problems: 1) The sub-bass

performance will suffer due to the

movement of the enclosure caused by

the force exerted by the woofer(s) and

2) A loose enclosure presents a serious

safety hazard in the event of a collision

or sudden deceleration.

Please enjoy your JL Audio Stealthbox

responsibly.

STEP 1:

From inside the factory console,

using a 9/16” socket, remove the four bolts

that secure the console to the vehicle. ( Two

of these bolts will be used later to secure

the Stealthbox).

STEP 2:

Remove the console from the vehi-

cle.

STEP 3:

Remove the inside section of the

console. (This will not be reinstalled).

-Two screws are located under the front tray.

-Three screws attach the hinge.

-Three screws are located on each side of the

consoles shell (six total)

After this section is removed, the console shell

will be in two parts.

STEP 4:

Using a pair of pliers, from the inside

of the console shell. Remove the ridges locat-

ed toward the front of the console.

STEP 5:

Reassemble the front and rear parts

of the console shell using the supplied hard-

ware (4 #8 x 1/2” long screws, 4 washer and

4 nuts) as shown in the picture.

STEP 6:

Turn the console shell upside down.

Position the Stealthbox inside the shell,

START

HERE

Continued on Next Page ➔

w w w . j l a u d i o . c o m

➔

STEP 7: Use the remaining mounting holes as a

drill guide.

Using a 1/8” drill bit and drill, drill a hole through

each of these guide holes, into the Stealthbox.

STEP 8: Install #8x 1/2” black pan-head screws

into the drilled holes.

➔ ➔

➔➔➔

STEP 10: Install #8 x 1/2” black pan-head screws

into the drilled holes.

Cont..

From

Page

Continued on Next Page ➔

➔

STEP 11: Using a 1/8” drill bit and drill. Drill two

holes at the hinge area using the outside holes only.

The center hole does not need to be drilled.

➔

STEP 12: Remove the screws installed in STEP 8

and STEP 10. Separate the console shell from the

Stealthbox.

STEP 13: Attach the OEM’s console lid to the

shell. Use one of the OEM’s screws and supplied

speed-clip to the center hole of the hinge.

STEP 9: Turn the console right-side-up with the

Stealthbox attached.

Using the holes on the top of the console shell as

guides, use a 1/8” drill bit and drill to drill holes

through each of these guide holes and into the

Stealthbox.

SB- F - S U P R C N S L / 1 0 W 3 V2 , J L AU D I O , I n c 2 0 0 5 Sh e e t S K U # 0 1 1 1 4 9 R e v i s io n 8 / 4 / 2 0 0 5 Pag e 2

w w w . j l a u d i o . c o m

STEP 14: Place the Stealthbox in the vehicle. Using

a pair of OEM bolts, from STEP 1. Loosely secure

the rear foot bracket to the floor, do not tighten.

STEP 15: Remove the paper backing on the sup-

plied sheet wax squares.

With the Stealthbox in place, lift the front of the

Stealthbox and position both supplied sheet wax

squares onto the carpet and lined up with the front

foot bracket of the Stealthbox, lower the console

down.

STEP 16: Using one of the supplied 3/8”x1-1/2”

bolts, place the bolt through each hole of the front

foot bracket (one at a time). Press down on the bolt,

too leave impressions on the sheet wax squares.

STEP 17: Remove the two OEM bolts from STEP

14. Remove the Stealthbox from the vehicle.

➔ ➔

➔ ➔ ➔

VEHICLE SHEET METAL

METAL BRACE PLATE

FLAT WASHER

HEX NUT

FRONT MOUNTING BRACKET

OF BRACKET

LOCK WASHER

FLAT WASHER

BOLT

STEP 19: Run speaker wire to the Stealthbox’s

location. Make sure the speaker wire is going to be

accessible at the rear of the Stealthbox.

*At this time, double check for proper oper-

ation of woofer*.

Cont..

From

Page

Continued on Next Page ➔

➔

STEP 18: With a 1/8” drill bit and drill, drill a pilot

hole.

With a 1/2” drill bit and drill, drill a hole through each

of the two locations.

*Caution: Check under the vehicle for any

loose brake lines, fuel lines, transfer case or

other hazards before drilling.Always wear

eye protection when drilling. *

➔

STEP 22: A second person is needed to help out in this

step.

Place a supplied flat washer onto each supplied 3/8”x1-1/2”

bolt. Place each bolt assembly through the front bracket of

the Stealthbox and the drilled holes from STEP 18.

From under the vehicle, place the supplied metal brace plate,

flat washer, lock washer and nut onto each bolt assembly.

With a second person inside the vehicle securing the bolt

head with an open-end wrench.Tighten the nut onto the

bolt assembly.

STEP 21: Replace the OEM bolts back to

the rear foot bracket. Hand-tighten the rear

bolts.

SB- F - S U P R C N S L / 1 0 W 3 V2 , J L AU D I O, I n c 2 0 0 5 Sh e e t S K U # 0 1 1 1 4 9 R e v i s io n 8 / 4 / 2 0 0 5 Pag e 3

w w w . j l a u d i o . c o m

STEP 25: Tighten the bolts at the rear of the

Stealthbox, inside the vehicle.

STEP 26: Connect the speaker wire to

the terminal cup on the Stealthbox.

STEP 27: Place the pair of supplied alu-

minum spacers over the two holes that are

located at the upper rear of the Stealthbox,

From STEP 11.

STEP 20: Position the Stealthbox back into place.

Product specificaties

Merk:	JL Audio
Categorie:	Niet gecategoriseerd
Model:	Stealthbox SB-F-SUPRCNSL/10W3v3

Heb je hulp nodig?

Als je hulp nodig hebt met JL Audio Stealthbox SB-F-SUPRCNSL/10W3v3 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd JL Audio

JL Audio Stealthbox SB-F-ESCP/10W1v3 Handleiding

15 November 2024

JL Audio Stealthbox SB-J-JL4DDRV/10TW1-2 Handleiding

15 November 2024

JL Audio MediaMaster 55-HR Handleiding

7 Augustus 2024

JL Audio MediaMaster 55 Handleiding

7 Augustus 2024

JL Audio MBT-RXv2 Handleiding

9 Juli 2024

JL Audio MBT-CRXv3 Handleiding

9 Juli 2024

JL Audio Stealthbox SBX-F-MAVG1/10TW1 Handleiding

10 Juni 2024

JL Audio Stealthbox SBX-T-TACDCG3/10TW3 Handleiding

10 Juni 2024

JL Audio MediaMaster MM105-HR Handleiding

11 Maart 2024

JL Audio JLINK RX Handleiding

8 Januari 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Kolcraft MLB Chicago Cubs Handleiding

26 November 2024

Kolcraft MLB New York Yankees Handleiding

26 November 2024

Kolcraft MLB San Francisco Giants Handleiding

26 November 2024

Kolcraft MLB St. Louis Cardinals Handleiding

26 November 2024

Nedis POCO106 Handleiding

26 November 2024

Nedis BTSM1GY Handleiding

26 November 2024

Turbosound TPOLEAJ-01 Handleiding

26 November 2024

Turbosound TSTAND-01 Handleiding

26 November 2024

IFM TAD981 Handleiding

26 November 2024

IFM TAD961 Handleiding

26 November 2024