JANDY JUVLP200 Handleiding

JANDY Niet gecategoriseerd JUVLP200

Lees hieronder de 📖 handleiding in het Nederlandse voor JANDY JUVLP200 (12 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 2 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/12

Installation and Operation Manual

Manuel d’installation et d’utilisation

Manual de instalación y operación

UV Low Pressure HMAC

Models: JUVLP100, JUVLP150, JUVLP200, JUVLP250

WARNING

FOR YOUR SAFETY – This product must be installed and serviced by a contractor who is licensed and qualiﬁed in pool equipment by the jurisdiction in which the product will be installed

where such state or local requirements exist. The maintainer must be a professional with sufﬁcient experience in pool equipment installation and maintenance so that all of the instructions

in this manual can be followed exactly. Before installing this product, read and follow all warning notices and instructions that accompany this product. Failure to follow warning notices

and instructions may result in property damage, personal injury, or death. Improper installation and/or operation may void the warranty.

Improper installation and/or operation can create unwanted electrical hazard which may cause serious injury, property damage, or death.

ATTENTION INSTALLER – This manual contains important information about the installation, operation and safe use of this product. This information should be given

to the owner/operator of this equipment.

Page 2

ENGLISH Jandy® UV Low Pressure HMAC | Installation & Operation Manual

Table of Contents

EQUIPMENT INFORMATION RECORD

DATE OF INSTALLATION _______________________________________________________________________________

INSTALLER INFORMATION _____________________________________________________________________________

INITIAL PRESSURE GAUGE READING (WITH CLEAR FILTER) ____________________________________________

PUMP MODEL ________________________________ HORSEPOWER ____________________________________

NOTES _______________________________________________________________________________________________

______________________________________________________________________________________________

SAVE THESE INSTRUCTIONS

Section 1. Important Safety Instructions 3 .........

1.1 Safety Instructions 3 .........................................

Section 2. General Description 4 .........................

2.1 UV Disinfection 4 ...............................................

2.2 Product Speciﬁcations 4 ...................................

2.3 Dimensions ..................................................... 5

2.4 System Description 6 ........................................

2.5 Product Contents 6 ...........................................

Section 3. Pool Water 7 ........................................

3.1 Suggested Size Selection 7 ..............................

3.2 Pool Water Conditions 7 ...................................

Section 4. Installation 8 ........................................

4.1 Installation Requirements 8 ...............................

4.2 Installation of the UV Reactor 8 ........................

4.3 Electrical Connections 9 ...................................

4.4 Control Panel: Field Wiring Diagram 10 ............

4.5 Lamp Connection 14 .........................................

Section 5. Operation 15 ........................................

5.1 Initial Start-up 15 ...............................................

5.2 System Controls 16 ...........................................

5.3 Alarms ..........................................................16

Section 6. Maintenance 17 ...................................

6.1 Replacing the UV Lamp 17 ...............................

6.2 Reset the Hour Counter 18 ...............................

6.3 Replacing / Cleaning a Quartz Sleeve 18 ..........

6.4 Replacing Seal in Contact with the

Quartz Sleeve 20 ...............................................

6.5 Replacing the Inner SS Reﬂector 21 .................

6.6 Control of System Isolation and

Connections 21 .................................................

6.7 Winterizing ...................................................21

Section 7. Troubleshooting 22 .............................

Section 8. Exploded Views and

Replacement Kits........................... 23

Page 3

Jandy® UV Low Pressure HMAC | Installation & Operation Manual ENGLISH

Section 1. Important Safety Instructions

READ AND FOLLOW ALL INSTRUCTIONS

1.1 Safety Instructions

All electrical work must be performed by a licensed electrician and conform to all national, state, and local

codes. When installing and using this electrical equipment, basic safety precautions should always be

followed, including the following:

DANGER

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience

and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

Installation and manipulation should only be performed by a qualiﬁed technician.

Do not use this equipment for any purpose other than that for which it was designed. Applicable standards for prevention of accidents and for

electrical installations must be respected.

Never remove the retention nut of the quartz tube when water is circulating inside the reactor, since it could be ejected, causing damage.

The UV radiation produced by this equipment can cause serious harm if eyes or skin are exposed directly to the lamp. Never connect the equipment

when the lamp is outside the reactor. Never handle the UV lamp until it is completely cold.

WARNING

To reduce the risk of severe injury or death, do not operate the UV emitter when it is removed from the appliance enclosure. Unintended use of the

appliance or damage to the housing may result in the escape of dangerous UV radiation. UV radiation may, even in little doses, cause harm to the

eyes and skin. Never look directly at an illuminated UV lamp.

RISK OF ELECTRIC SHOCK, FIRE, PERSONAL INJURY, OR DEATH.

• Installation must be done in accordance with the National Electrical Code

(NEC®

, NFPA-70) and/or any other applicable local and national

installation codes.

• Use equipment only in a pool or spa installation.

• Maintain circulation system properly. Replace worn or damaged parts immediately.

ATTENTION

UV LP treatment systems operate with a supply of 120-240 VAC /60 Hz/1 phase. Do not alter the power supply to operate at any other voltage. Ensure

that all electrical connections are properly tightened and check for bad connections that could overheat.

Risk of electric shock - Install the power center at least ﬁve (5) feet (1.52 m) from the inside wall of the pool and/ or hot tub using non-metallic

plumbing. Canadian installations must be at least three (3) meters from the water.

Children should not use spas or hot tubs without adult supervision. Do not use spas or hot tubs unless all suction guards are installed to prevent body

and hair entrapment. People using medications and/or having an adverse medical history should consult a physician before using a spa or hot tub.