Jablotron TP-98 Handleiding

Jablotron Thermostaat TP-98

Lees hieronder de 📖 handleiding in het Nederlandse voor Jablotron TP-98 (1 pagina's) in de categorie Thermostaat. Deze handleiding was nuttig voor 12 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/1

Wireless thermostat TP-98 - 2 - MFR51500

Wireless thermostat TP-98

This thermostat can replace a common indoor residential thermostat. It

is designed to be used with electric, gas or oil heating system. The

easy to read display shows the current room temperature and

temperature adjustment is very simple. The main advantage is that

there is no need of a cable between the thermostat and the heating

system.

Installation

The TP-98TX should be mounted

in a dry indoor location. Choose a

mounting location about 1.5 meters

above the floor in the area with

good air circulation. Avoid places

with drafts, dead air spots and

radiant heat from the sun or

appliances. It should not be

installed close to any metal

structure or other objects that may

obstruct radio signal transmissions.

1. Remove the front housing of the thermostat. (using a screwdriver)

2. Insert the batteries. Current temperature will appear on the display if

not check the batteries.

3. Attach the thermostat to the wall with the two screws.

Mounting the receiver unit

Place the receiver unit in a suitable place near the heater. Wiring

of the unit to the heater should be done only by a professional

electrician:

1. Release the upper cover by pressing the plastic log on the top side

of housing.

2. Release the internal cover (1 screw).

3. Mount the unit to the desired location (2 screws).

4. Connect power 230VAC / 50Hz to terminals L and N.

5. Two PE terminals are available for a protective earth connection.

6. Terminals C (common), N.O. (normally open) and N.C. (normally

closed) are outputs of the relay contact. This contact is protected by

a 6.3A fuse. The contacts are galvanic separated.

Note: The

thermostat, which

has a unique code,

is enrolled to the

receiver unit from

the factory.

A built-in LED

indicator indicates a

status of the output

relay.

TEMPERATURE SETTING

In the normal operation mode the thermostat shows the room

temperature. To set a desired temperature:

1. Press or button to view the set temperature. The sign SET

will appear on the display.

2. Hold or button for approximately 3 seconds till the

temperature indicator will flash once.

3. Use or button to increase or decrease the temperature

setting. If no button is pressed for 10 seconds the unit will be

switched back to the normal operation mode.

The programmed temperature range is from 5˚C to 35˚C.

The temperature span between switching ON and OFF is 1˚C. For

example, if the temperature setting is 20˚C, the heater will be switched

on when the room temperature drops to 19.5˚C and will be switched off

when the temperature rises to 20.5˚C. When the thermostat is on the

symbol HEAT will be shown on the display.

When the temperature is above 40˚C ‘HI’ will be shown on the LCD

and ‘LO’ will be shown when temperature falls below 0˚C.

When the voltage of the batteries is low the LCD will be turned off. In

that case the batteries should be changed.

Enrolment of the thermostat into the receiver unit

The thermostat has already been enrolled to the receiving unit in

the factory. If you change the thermostat for a new one it must be

enrolled to the receiver unit in the following way:

1. Remove the batteries from the thermostat for 2 minutes.

2. Remove the upper housing from the receiver unit.

3. Keep pressing the button inside the receiver until the 4th LED starts

flashing.

4. Place the batteries into the thermostat. The LEDs in the receiver will

flash once to confirm the enrolment.

Note: Each receiver unit can cooperate only with one thermostat. If any

other device (remote control etc.) has been enrolled to the receiver the

receiver must be reset before enrolment of the thermostat. To reset the

memory make the 4th LED flashing by pressing the button and then

press and hold the button until all LEDs flash rapidly.

Specifications

Thermostat TP-98TX

Power Source: two AAA 1.5V Alkaline batteries

Temperature Measurement: 0 - 40˚C

Temperature Accuracy: ±1.0˚C

Temperature Control: 5 - 35˚C

Temperature Control Span: 0,5˚C

Output On Delay: 20 seconds

Working frequency 433,92 MHz

Working distance up to 100 m (open area)

Coding: digital, each thermostat has a unique

floating code

Operating Temperature: -10˚C to 50˚C (non-condensing)

Storage Temperature: -30˚C to 60˚C

Size: 73.5 X 28.0 X 73.5 mm

Housing: Polycarbonate (PC)

Weight: 90 g (battery not included)

Receiver unit UC-222

Voltage: 230 V AC

Power consumption: max. 1 W

Operating frequency: 433.92 MHz

Coding: digital, each thermostat has

a unique floating code

Output relay: over switching dry contact

Fused 6 A at 250 V

Can be operated according to ERC REC 70-03

Hereby, Jablotron Ltd., declares that this TP-98 is in compliance with

the essential requirements and other relevant provisions of Directive

1999/5/EC.

Note: Dispose of batteries safely depending on the type of the

batteries and local regulation. Although this product does not contain

any harmful materials we suggest you to return the product to the

dealer or directly to the producer after usage.

Relé

Product specificaties

Merk:	Jablotron
Categorie:	Thermostaat
Model:	TP-98

Heb je hulp nodig?

Als je hulp nodig hebt met Jablotron TP-98 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Thermostaat Jablotron

Jablotron TP-83 Handleiding

26 Maart 2024

Jablotron TP-83IR Handleiding

26 Maart 2024

Jablotron TP-98 Handleiding

26 Maart 2024

Handleiding Thermostaat

Nieuwste handleidingen voor Thermostaat

Wodtke ET 2 Handleiding

20 Februari 2025

Netatmo Smart Radiator Valve Handleiding

26 Februari 2025

Konyks eCosy Handleiding

26 Februari 2025

AcuRite 00523 Handleiding

20 Februari 2025

Sorel MHCC Handleiding

18 Februari 2025

Rose LM TH-H Handleiding

1 Februari 2025

Vemer Tuo 4G Handleiding

29 Januari 2025

Homematic IP HmIP-WTH-B-A Handleiding

28 Januari 2025

Tru Components TCN4S-24R Handleiding

18 December 2024

Tru Components TK4S-14RC Handleiding

18 December 2024