Jablotron TP-80 Handleiding

Jablotron Thermostaat TP-80

Lees hieronder de 📖 handleiding in het Nederlandse voor Jablotron TP-80 (1 pagina's) in de categorie Thermostaat. Deze handleiding was nuttig voor 6 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/1

The TP-80 wireless thermostat 1 / 1 MJF51100

The TP-80 wireless thermostat

The TP-80 thermostat can be used to set the temperature in a room by

turning the setting knob. It has anti-freeze protection and when combined

with an Oasis wireless security system (Jablotron), the following features

are possible:

• Switching the heating ON and OFF remotely (by mobile phone, remote

control or Internet),

• Disabling the heating when windows are open,

• Informing the user about heating faults and frost threat (if the

temperature drops below +3°C a warning SMS is sent),

• Informing on the occurrence of fire (when the temperature is above

+60°C).

The thermostat is battery-powered. The main advantage is that there is

no need for a cable between the thermostat and the heating system.

Indication that the room temperature

is lower than the set temperature

Low battery indicator

Installation

The thermostat should be mounted in a dry indoor location. Choose a

mounting location about 1.5 meters above the floor in an area with good air

circulation. Avoid places with draughts, dead air spots and radiant heat

from the sun or appliances. It should not be installed close to any metal

structure or other objects that may obstruct radio signal transmissions.

1. Release the upper cover by pressing the plastic tab (e.g. by a

screwdriver) on the right side of the housing.

2. Mount the rear part of the unit on to the desired location (tab on the

right side).

3. If the thermostat was purchased as a kit along with a receiving unit,

connect the thermostat’s battery (pull out the red tape to activate the

battery). Otherwise see the section “Mounting the receiving unit”.

4. Close the thermostat.

Mounting the receiving unit

Install and connect the receiving unit to the heating system. If the

receiving unit was purchased separately then the thermostat must be

enrolled to it – enter enrollment mode on the receiving unit (see its manual)

and connect the battery to the thermostat.

Temperature setting

• By turning the knob the desired temperature can be set from +6 to

+28°C.

• If the desired temperature is higher than the current temperature,

the red LED lights during temperature setting (it switches off 3 seconds

after the last movement of the knob).

• The thermostat maintains the set temperature within an accuracy of

±0.5˚C (e.g. if it is set to 24˚C, it switches the heating on when the

temperature drops below 23.5˚C and it switches it off if the temperature

goes above 24.5˚C). In reality the temperature scatter can be slightly

higher because of the temperature persistence in the room.

Integration into the OASIS system

• The thermostat can also be enrolled to control panel as a detector. If

the temperature decreases below +3°C a panic alarm will be triggered

= frost threat (heating failure). If the temperature exceeds 60°C then a

fire alarm will be triggered.

• An AC-82 receiving unit has two output relays (X and Y). TP-80

thermostats can be enrolled separately to each relay in order to control

two independent heating circuits.

• To enable/disable a heating system the Oasis control panel can also

be enrolled (sequence 299) to the receiving unit (AC-82). To disable the

heating or thermostat means the heating system only heats when the

temperature is below +6°C. A thermostat enrolled to the X relay can

be enabled/disabled via the PGX programmable output, and a

thermostat enrolled to the Y relay enabled/disabled via PGY. If the

programmable output of the control panel is switched on, the

thermostat maintains the set temperature. If the control panel’s output is

switched off the thermostat only triggers heating if the temperature

drops below 6°C (anti-freeze protection).

• To control the heating, remote controls RC-80 (or RC-88) can also

be enrolled to a receiving unit (AC-82). The heating can be switched on

by remote controls (or ) to heat to the desired temperature and

also switched off (or ) where it only heats when the

temperature is below 6°C.

• To disable heating when windows are open JA-80M or JA-82M

detectors can also be enrolled to the receiving unit (AC-82). If the

windows are closed it heats to the desired temperature and if windows

are open it heats only when the temperature is below 6°C.

• Up to 8 thermostats can be enrolled to a single relay of the receiving

unit (AC-82). If at least one thermostat transmits a heat command then

the relay will be switched on.

Battery replacement

Replace the battery when the yellow low-battery indicator on the lower

right corner of thermostat is lit. Use only AA 1.5V alkaline battery.

Specification

Power supply: 1x alkaline battery AA 1.5 V

Battery lifetime: typically 1 year

Temperature Measurement: +6 to +28 ˚C

Temperature Accuracy: ±0.5 ˚C

Anti-freeze protection heating threshold: +6°C

Freeze alarm (panic transmission) temperature threshold: <+3°C

Fire alarm temperature threshold: >+60°C

Operational frequency: 868 MHz, Oasis protocol

Operational radio range: up to 100 m (open area)

Operational temperature range: -10 ˚C to + 60 ˚C (low humidity)

Dimensions: 73 x 73 x 40 mm

Can be operated according to ERC REC 70-03

Jablotron Ltd. hereby declares that the TP-80 is in compliance with

the essential requirements and other relevant provisions o

Directive 1999/5/EC. The original of the conformity assessmen

can be found on the web site www.jablotron.com, Technical

Support section.

Note: Dispose of batteries safely depending on battery type and local

regulations.Although this product does not contain any harmful

materials we suggest you return the product to the dealer or directly t

the manufacturer after use.

73 40

Product specificaties

Merk:	Jablotron
Categorie:	Thermostaat
Model:	TP-80

Heb je hulp nodig?

Als je hulp nodig hebt met Jablotron TP-80 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Thermostaat Jablotron

Jablotron TP-83 Handleiding

26 Maart 2024

Jablotron TP-80 Handleiding

26 Maart 2024

Jablotron TP-83IR Handleiding

26 Maart 2024

Jablotron TP-98 Handleiding

26 Maart 2024

Handleiding Thermostaat

Nieuwste handleidingen voor Thermostaat

Bticino XW8003W Handleiding

8 April 2025

Sorel RC21 Handleiding

18 Februari 2025

Hoffman ATEMNO Handleiding

4 April 2025

Wodtke FT1 Handleiding

20 Februari 2025

Fantini Cosmi L02D Handleiding

31 Maart 2025

Fantini Cosmi C800WIFI Handleiding

31 Maart 2025

Fantini Cosmi C820RQ Handleiding

31 Maart 2025

Fantini Cosmi L02C Handleiding

31 Maart 2025

Fantini Cosmi L02A Handleiding

31 Maart 2025

Fantini Cosmi L03B Handleiding

31 Maart 2025