Jablotron JA-80W Handleiding
Jablotron
Beveiliging
JA-80W
Lees hieronder de đź“– handleiding in het Nederlandse voor Jablotron JA-80W (1 pagina's) in de categorie Beveiliging. Deze handleiding was nuttig voor 51 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/1
JA-80W wireless combined PIR + MW detector 1 MLI51101
JA-80W wireless combined PIR + MW detector
The JA-80W is a component of Jablotron’s Oasis alarm system. It is
designed to detect human body movement inside buildings. A high immunity to
false alarms is reached thanks to the combination of PIR and microwave (MW)
detection. The PIR part, if triggered, starts the MW detection to confirm PIR
activation. Only then is the triggering transmitted.
Installation
Installation shall only be undertaken by technicians holding a certificate
issued by an authorized distributor. There should be no obstacles blocking the
detector’s “view” of the protected area. Keep the detector away from metal
objects which could interfere with radio communication and the MW field.
8
Description: 1. DIP-switch; 2. MW part connector; 3.PCB tab; 4. tamper-switch; 5.
PIR sensor; 6. front cover tab; 7. MW sensitivity setting; 8. MW detector
1. Open the detector cover by pressing the tab (6) and remove the PCB
which is held by an internal tab (3) Avoid touching the internal PIR
element or damaging the antenna.
2. Punch screw holes through the rear plastic cover according to the
installation point, either for a corner or for a flat wall At least one screw
should penetrate the tamper-sensitive section.
3. Screw the rear cover to the wall, about 2.5 meters above the floor
(vertically, with the tab down).
4. Return the PCB to its original place till the tab (3) clicks..
5. Leave the battery disconnected and the cover open and then follow the
control panel or receiver manual. The basics of enrollment are:
• Enter enrollment mode on the control panel by keying in “1” in
Service mode.
• Install a battery into the detector to activate enrollment.
• Exit enrollment mode by pressing “#”
6. Close the detector cover till the tab clicks. The supplied screw can secure
the tab.
7. After installing a battery into the detector, allow three minutes for
stabilization. During this period the LED is continuously lit.
Notes:
To enroll a detector after having already connected a battery, first disconnect
the battery, and press and release the tamper switch to discharge any
remaining charge to get the device ready for enrollment.
The detector can also be enrolled by entering the serial number – the last
eights numbers of the barcode, which is placed inside the detector.
To follow the EN 50131-2-4 the tab must be secured by the supplied screw.
DIP switch Setting
Switch no.1: DEL / INS: OFF (DEL) provides entrance & exit delays for
detectors installed in a building entrance route. The ON (INS) allows the
detector to instantly trigger alarm activation if the control panel is armed.
DIP switch no.1 only has an effect if the detector has a natural reaction
assigned to it in the OASiS control panel. It also has no effect when used with
a UC-8x or AC-8x receiver.
Switch no.2: PIR NORM / HIGH: selection of immunity to false alarms.
The OFF (NORM) position combines very good immunity with fast sensor
reactions. The ON (HIGH) position gives increased immunity with a slower
reaction time and is only used for problematic installations.
Switch no.3: MW NORM / HIGH sets the time period after PIR detection in
which the MW detection is active. The position OFF – 1 s, ON – 2 s
Switch no.4: MW NORM / TEST. The position OFF is for the standard function
of the detector. The MW detection is triggered by the PIR detection part for one or
two seconds according to switch no.3. The position ON - MW detection works
continuously for testing purposes (walk test).
Testing the detector
15 minutes after closing the detector cover, the LED indicators show detector
activation. A short flash of the red light indicates PIR detection and a long flash
(2 sec) indicates MW confirmation of the movement.
For the proper functioning of the detector, it is essential to set the MW
detection field according to the place which should be monitored. For setting
up, switch the fourth DIP switch to the TEST position. Sensitivity (monitoring
range) can be adjusted by a potentiometer on the MW detection part located
inside the front cover of the detector. Turning clockwise increases the
sensitivity (range). Avoid selecting too high a sensitivity as the detection can
cover e.g. nearby rooms. Generally the MW detection field should be the same
as the PIR detection one. After setting up, switch the DIP switch back to
NORM position.
To save battery energy, the PIR detector switches to battery-save mode 15
minutes after the cover is closed. During battery-save mode the PIR sensor still
always watches out for movement. The first movement detected and consecutively
confirmed by the MW part is then signaled to the control panel instantly, and for the
next 5 minutes the PIR sensor ignores any further movement. After these 5
minutes, the PIR sensor then returns to watching out for movement until re-
triggered.
Battery replacement
The detector regularly checks its battery conditions. If battery voltage is
too low, then the report is sent to the control panel to inform the user or
installer. The detector continues to work and each detected movement is
confirmed by a brief LED flash. The battery should be replaced within two
weeks by a qualified technician in SERVICE mode.
After battery replacement, test the functioning of the detector. Expired
batteries should not be thrown into the garbage, but disposed of according
to local regulations.
Removing the detector from the system
If a detector is removed, the control panel reports the removal. The detector
has to be deleted from its address in the control panel before intentional
removal.
Detection characteristics
Technical parameters
Power supply: Lithium battery type LS(T)14500 (3.6V / 2,4 Ah AA)
Typical battery lifetime: approx. 2 years (DIP switch 3: NORM)
Communication band: 868 MHz, Oasis Protocol
Communication range: approx. 300m (open area)
Recommended installation height: 2.0 to 2.5 m above floor level
PIR detection angle/detection range: 110° / 12 m (with basic lens)
MW detection range / frequency 0.5 to 20 m / 9.35 GHz
Operational environment according to EN 50131-1 II. indoor general
Operational temperature range -10 to +40 °C
EN 50131-1, EN 50131-2-4, EN 50131-5-3 classification: grade 2
Dimensions, weight 110 x 60 x 55 mm, 140 g
Complies with ETSI EN 300220, ETSI EN 300 440-1, EN 50130-4, EN 55022, EN 60950-1
Can be operated according to ERC REC 70-03
Operation requires notification national telecommunication offices of Finland, France, Italy,
Serbia and Montenegro, Spain, Sweden, UK
JABLOTRON ALARMS a.s. hereby declares that the
JA-80W is in compliance with the essential requirements
and other relevant provisions of Directive 99/5/EC. The
original of the conformity assessment can be found at
www.jablotron.com, Technical Support section
Note: Although this product does not contain any harmful
materials we suggest you return the product to the dealer or
directly to the producer after use.
Product specificaties
| Merk: | Jablotron |
| Categorie: | Beveiliging |
| Model: | JA-80W |
Heb je hulp nodig?
Als je hulp nodig hebt met Jablotron JA-80W stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Beveiliging Jablotron
20 Maart 2023
20 Maart 2023
20 Maart 2023
20 Maart 2023
20 Maart 2023
20 Maart 2023
20 Maart 2023
20 Maart 2023
20 Maart 2023
20 Maart 2023
Handleiding Beveiliging
- Beveiliging Bosch
- Beveiliging Panasonic
- Beveiliging Bticino
- Beveiliging Fysic
- Beveiliging Grundig
- Beveiliging Honeywell
- Beveiliging Medion
- Beveiliging Siemens
- Beveiliging Abus
- Beveiliging AceSee
- Beveiliging Airbolt
- Beveiliging Ajax
- Beveiliging Alecto
- Beveiliging Alhua - Dahua
- Beveiliging Alphatronics
- Beveiliging AngelEye
- Beveiliging Aritech
- Beveiliging Audiovox
- Beveiliging AVTech - Velleman
- Beveiliging Axa
- Beveiliging Axis
- Beveiliging Basetech
- Beveiliging Batavia
- Beveiliging Bavaria
- Beveiliging Bellman
- Beveiliging Bitron Video
- Beveiliging Blaupunkt
- Beveiliging BML
- Beveiliging Bolyguard
- Beveiliging Brennenstuhl
- Beveiliging BRK
- Beveiliging BRK DICON
- Beveiliging Dahua
- Beveiliging Dedicated Micros
- Beveiliging Dericam
- Beveiliging Devolo
- Beveiliging Directed Electronics
- Beveiliging Dnt
- Beveiliging Doro
- Beveiliging Dymond
- Beveiliging Easy Home
- Beveiliging Easymaxx
- Beveiliging Eden
- Beveiliging Edimax
- Beveiliging Ednet
- Beveiliging Electronics Line
- Beveiliging Elkron
- Beveiliging Elro
- Beveiliging Elro-Flamingo
- Beveiliging Eminent
- Beveiliging Entrya
- Beveiliging Epine
- Beveiliging Eufy
- Beveiliging Ezviz
- Beveiliging FBII
- Beveiliging Fenton
- Beveiliging First Alert
- Beveiliging Flamingo FA15RF
- Beveiliging FlinQ
- Beveiliging Foscam
- Beveiliging Fracarro
- Beveiliging Friedland
- Beveiliging Galaxy
- Beveiliging GE Security
- Beveiliging Geemarc
- Beveiliging Gira
- Beveiliging Goliath
- Beveiliging Golmar
- Beveiliging Goobay
- Beveiliging Grandstream
- Beveiliging Grothe
- Beveiliging Guardall
- Beveiliging Hagenuk
- Beveiliging Heidemann
- Beveiliging Hikvision
- Beveiliging Home Protector
- Beveiliging Home8
- Beveiliging HomeWizard
- Beveiliging HUMANTECHNIK
- Beveiliging I-onik
- Beveiliging I-Tel
- Beveiliging Iget
- Beveiliging Iiquu
- Beveiliging Indexa
- Beveiliging Inner Range
- Beveiliging Interlogix
- Beveiliging Kocom
- Beveiliging Kompernass
- Beveiliging Kopp
- Beveiliging Ksenia
- Beveiliging Lamax
- Beveiliging LevelOne
- Beveiliging Logicom
- Beveiliging Maginon
- Beveiliging Marmitek
- Beveiliging Marquant
- Beveiliging ME
- Beveiliging Microtech
- Beveiliging Mikros
- Beveiliging Monacor
- Beveiliging Mr Safe
- Beveiliging Muller
- Beveiliging Myfox
- Beveiliging Nedis
- Beveiliging Nemef
- Beveiliging Nest
- Beveiliging Netatmo
- Beveiliging NetBotz
- Beveiliging Netgear
- Beveiliging NetworX
- Beveiliging Niko
- Beveiliging Nor-tec
- Beveiliging Notifier
- Beveiliging Paradox
- Beveiliging Perel
- Beveiliging PIR Alarm
- Beveiliging Plustek
- Beveiliging Powerfix
- Beveiliging Powermax
- Beveiliging Prestigio
- Beveiliging Profile
- Beveiliging PROmax
- Beveiliging Protector
- Beveiliging Provision ISR
- Beveiliging QuattSecure
- Beveiliging Ranex
- Beveiliging RISCO Group
- Beveiliging Satel
- Beveiliging SecuFirst
- Beveiliging Secure Pro
- Beveiliging Securitas
- Beveiliging Selvag
- Beveiliging Skytronic
- Beveiliging Smanos
- Beveiliging Smartalarm
- Beveiliging SmartHome
- Beveiliging Smartwares
- Beveiliging Somfy
- Beveiliging Sonic Alert
- Beveiliging Steinel
- Beveiliging Stobo
- Beveiliging Storage Options
- Beveiliging Storex
- Beveiliging Switel
- Beveiliging Sygonix
- Beveiliging Technaxx
- Beveiliging Tegui
- Beveiliging Tevion
- Beveiliging Theben
- Beveiliging Topcraft
- Beveiliging Trebs
- Beveiliging Trendnet
- Beveiliging Trust
- Beveiliging Unitec
- Beveiliging Unitron
- Beveiliging Urmet
- Beveiliging V-Tac
- Beveiliging Velbus
- Beveiliging Velleman
- Beveiliging Visonic
- Beveiliging Voxx
- Beveiliging Waeco
- Beveiliging Wanscam
- Beveiliging Woonveilig
- Beveiliging Xavax
- Beveiliging Xena
- Beveiliging Y-cam
- Beveiliging Yale
- Beveiliging Zmodo
- Beveiliging Jacob Jensen
- Beveiliging Jung
- Beveiliging Jupiter Pro
- Beveiliging Juwel
- Beveiliging One2track
- Beveiliging Oplink
- Beveiliging Optex
- Beveiliging Orbis
- Beveiliging Overmax
- Beveiliging Fito
- Beveiliging One Concept
Nieuwste handleidingen voor Beveiliging
6 Maart 2024
4 Februari 2024
16 Oktober 2023
16 Oktober 2023
16 Oktober 2023
16 Oktober 2023
16 Oktober 2023
16 Oktober 2023
16 Oktober 2023
16 Oktober 2023