Jablotron GBS-200 Handleiding

Jablotron Beveiliging GBS-200

Lees hieronder de 📖 handleiding in het Nederlandse voor Jablotron GBS-200 (1 pagina's) in de categorie Beveiliging. Deze handleiding was nuttig voor 41 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/1

Acoustic glass break detector GBS-200 2/2 MAV51500

ACOUSTIC GLASS BREAK DETECTOR GBS-200

A device for easy and reliable protection against robbery.

One sensor covers an entire room, regardless of the number of

windows. A dual technology detection method (air pressure

and sound analysis) is combined with digital processing to

guarantee high sensitivity to the breaking of all types of glass

(Plate, Tempered, Laminated, Wired). At the same time, it is

highly resistant to false alarms.

FEATURES

The GBS-200 detector has a relay contact output (N.C.),

tamper switch (N.C.), a jumper switch for selection of ALARM

MEMORY function, a jumper switch for manual testing mode

and variable resistor for sensitivity adjustment. There are three

LED's on the front side to indicate activation of the pressure

filter, activation of the sound filter and alarm (or alarm memory)

indication. For increased flexibility, the detector can be

mounted either to the ceiling or the wall.

For testing you can use a GLASS BREAK SIMULATOR

(model GBT-200), or you can conduct a manual "step by step"

test (testing mode).

SPECIFICATIONS:

Input voltage 10 – 16 V DC

current consumption 15 mA

alarm relay contact NC max. 0.5 A / 60 V DC

tamper switch output NC max. 0.5 A / 60 V DC

max. working distance 9 m

operating temperature -10 ° C to 55 °C

dimensions 100 x 74 x 27 mm

MOUNTING

The GBS-200 can be mounted on walls and ceilings. The unit

must have an unobstructed view of the protected glass (in the

case of heavy curtains, mount the unit on the widow frame

behind the curtains). After opening the detector unit by pressing

down on the plastic lock, take out the PCB module by removing

the screw. Then mount the rear housing of the GBS-200 case on

the desired surface. After mounting the case, replace the PCB

module back in the housing, being sure to secure it with the

screw.

WIRING: The terminals marked GND and +12V are connected

to the power supply. The two terminals marked NC are the

outputs for the normally closed alarm relay contacts. The

tamper switch is connected to the TMP terminals.

Testing and adjustment: Switch the 12V power supply ON

and wait for 60 seconds (warm-up time). You are now able to

test the sensitivity of the low frequency analysis channel. To do

this, strike carefully the glass with a cushioned instrument. If

the yellow LED on the detector flashes, then the low frequency

sensitivity is suitable. If the sensitivity is too low, adjust it with

the variable resistor PR1 (clockwise direction for higher

sensitivity). If the yellow LED flashes randomly, the sensitivity

is too high and you should use the PR1 resistor to lower the

sensitivity by turning it counter-clockwise.

For testing of the high frequency analysis channel and also

for complete testing, you should use the GBT-200 simulator

(refer to instructions in the simulator manual). Or, you can

conduct an easy manual test. For manual test mode, open the

AUDIO jumper. In this mode the green LED flashes when you

generate a high frequency sound of breaking glass. You can

simulate this sound easily with a piece of foamed plastic

(enclosed with each detector). To generate this high frequency

sound rub the protected glass with a wet piece of foamed

plastic. If the green LED flashes as a result of this sound, close

the AUDIO jumper and detector is now ready to work.

Alarm memory function: If you want this function, close the

MEM jumper. As a result, the red LED will remain lit after the

alarm is triggered.

You can reset the memory by opening the MEM jumper or

disconnecting the power. If you remove the MEM jumper, the

red LED will light only during ALARM output pulse and will

reset automatically. This function is particularly helpful in

determining which unit was triggered in a multiple detector

installation.

Final testing: To ensure maximum protection against false

alarms, try to activate any device in the area that may

automatically cycle such as pumps, generators, heating/air-

conditioning, etc. If the cycling device triggers an alarm, mount

the unit in a different location.

There is no need to relocate the detector if the cycling only

triggers the low frequency channel (the yellow LED flashes)

and not the high frequency channel.

Internet: www.jablotron.cz

Tel.: +420 483 559 999

fax: +420 438 559 993

Pod Skalkou 33

466 01 Jablonec nad Nisou

Czech Republic

Product specificaties

Merk:	Jablotron
Categorie:	Beveiliging
Model:	GBS-200

Heb je hulp nodig?

Als je hulp nodig hebt met Jablotron GBS-200 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Beveiliging Jablotron

Jablotron EYE-02 Handleiding

20 Maart 2023

Jablotron JA-60G Handleiding

20 Maart 2023

Jablotron JA-60B Handleiding

20 Maart 2023

Jablotron JA-63E Handleiding

20 Maart 2023

Jablotron JA-80D Handleiding

20 Maart 2023

Jablotron JA-50S Handleiding

20 Maart 2023

Jablotron JA-63F Handleiding

20 Maart 2023

Jablotron GBS-200 Handleiding

20 Maart 2023

Jablotron JA-63F wireless keypad Handleiding

20 Maart 2023

Jablotron CA-322 Accent Handleiding

20 Maart 2023

Handleiding Beveiliging

Nieuwste handleidingen voor Beveiliging

Geemarc SOS-PRO 295 Handleiding

6 Maart 2024

Technaxx TX-106 Handleiding

4 Februari 2024

One2track Safety Angel Handleiding

16 Oktober 2023

Sygonix SY-3851632 Handleiding

16 Oktober 2023

Sygonix 1326052 Handleiding

16 Oktober 2023

Sygonix 43588A WLAN Camera Handleiding

16 Oktober 2023

Sygonix 43176S LAN Camera Handleiding

16 Oktober 2023

Sygonix SY-3181234 Handleiding

16 Oktober 2023

Sygonix Touch IP65 Handleiding

16 Oktober 2023

Sygonix 1882082 Handleiding

16 Oktober 2023