Jablotron JA-80H Handleiding

Jablotron Beveiliging JA-80H

Lees hieronder de 📖 handleiding in het Nederlandse voor Jablotron JA-80H (1 pagina's) in de categorie Beveiliging. Deze handleiding was nuttig voor 43 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/1

The JA-80H outdoor keypad and RFID card reader MKM51101

The JA-80H outdoor keypad and RFID card reader

The JA-80H is a component of Jablotron’s Oasis

80 alarm system. It is designed to control access

(door lock) or to control a security system and

connects to the Oasis control panel via a WJ-80

interface.

Alternatively it can be connected to an AS-80 unit

as a part of a stand-alone access system.

The keypad sends data in Wiegand 26b format.

Installation

Installation shall only be undertaken by

technicians holding a certificate issued by an

authorized distributor. It is usually placed near an

entrance door (equipped with an electric lock). The

keypad can be used outdoors (conforms to IP-65).

1. Open the rear cover by unscrewing the screw

2. Prepare a hole in the wall for the keypad cable to

pass through, where the keypad will be located.

3. Attach the rear cover to the desired location (the

tamper spring must be properly pressed)

4. Pull the keypad cable through the wall hole and to the

interface unit’s box (WJ-80, AS-80)

5. Attach the keypad to the rear cover and secure it

using the screw

6. Connecting and setting up the keypad is described in

the WJ-80 or AS-80 manuals.

Cabling

wire signal

red +12V (power supply, 60mA)

green D0 (Wiegand 26b data output)

brown D1 (Wiegand 26b data output)

white TMP (normally closed tamper contact)

grey TMP (normally closed tamper contact)

yellow BZR (input controlling keypad sound – connecting to GND

generates a beep on the keypad)

blue GND (common ground)

pink not connected

Configuring the keypad for operation with the WJ-80

If the JA-80H keypad is connected to an Oasis control panel via a WJ-80

and it does not work as described in the manual, then it is not set to the

correct (factory default) operational mode. In such a case:

1. Switch the Oasis control panel to service mode

2. Disconnect the power from the control panel (mains and battery)

3. Disconnect the yellow and brown keypad wires from the terminals

and connect them together.

4. Power-up the control panel (keypad starts beeping)

5. Disconnect the yellow and brown wires (beeping will terminate)

6. On the JA-80H keypad, press button 4 (beeps once) and then button 3

(beeps several times)

7. Disconnect the power from the control panel, connect the yellow and brown

wires back up, power-up the control panel and check the proper functioning

of the JA-80H keypad

Technical specifications

Power supply 10 to 16V

Stand-by consumption typically 60mA

Housing IP65 (EN 60529)

Mechanical resistance IK08 (EN 50102)

Working environment class IV(EN 50131-1)

Operational temperature -25 to +60°C

RFID card Jablotron PC-01 or PC-02 (EM UNIQUE 125 kHz)

Dimensions 46 x 150.5 x 22.5mm

Length of the connection cable 1m

Complies with grade 2 (EN 50131-1, TS 50131-3)

Can be operated according to ERC REC 70-03

FCC ID VL6JA80H

Jablotron Ltd. hereby declares that the JA-80H is in compliance with the

essential requirements and other relevant provisions of Directive

1999/5/EC and complies with part 15 of the FCC rules. Operation is

subject to the following two conditions: 1. This device may not cause harmful

interference, and 2. This device must accept any interference received, including

interference that may cause undesired operation.

CAUTION: Changes or modifications no expressly approved by Jablotron

could void the user´s authority to operate the equipment. The original of the

conformity assessment can be found at www.jablotron.com, Technical

Support section.

Note: Although this product does not contain any harmful

materials we suggest you return the product to the dealer or

directly to the producer after use.

TAMPER

22,545

151,5

87,5

cca 1 m

Note: The red LED is lit in Oasis normal operating mode. Pressing a button

is confirmed by a flash from the orange LED.

How to set up the JA-80H keypad for the AS-80 access system is described in the AS-80 manual.

Product specificaties

Merk:	Jablotron
Categorie:	Beveiliging
Model:	JA-80H

Heb je hulp nodig?

Als je hulp nodig hebt met Jablotron JA-80H stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Beveiliging Jablotron

Jablotron EYE-02 Handleiding

20 Maart 2023

Jablotron JA-60G Handleiding

20 Maart 2023

Jablotron JA-60B Handleiding

20 Maart 2023

Jablotron JA-63E Handleiding

20 Maart 2023

Jablotron JA-80D Handleiding

20 Maart 2023

Jablotron JA-50S Handleiding

20 Maart 2023

Jablotron JA-63F Handleiding

20 Maart 2023

Jablotron GBS-200 Handleiding

20 Maart 2023

Jablotron JA-63F wireless keypad Handleiding

20 Maart 2023

Jablotron CA-322 Accent Handleiding

20 Maart 2023

Handleiding Beveiliging

Nieuwste handleidingen voor Beveiliging

Geemarc SOS-PRO 295 Handleiding

6 Maart 2024

Technaxx TX-106 Handleiding

4 Februari 2024

One2track Safety Angel Handleiding

16 Oktober 2023

Sygonix SY-3851632 Handleiding

16 Oktober 2023

Sygonix 1326052 Handleiding

16 Oktober 2023

Sygonix 43588A WLAN Camera Handleiding

16 Oktober 2023

Sygonix 43176S LAN Camera Handleiding

16 Oktober 2023

Sygonix SY-3181234 Handleiding

16 Oktober 2023

Sygonix Touch IP65 Handleiding

16 Oktober 2023

Sygonix 1882082 Handleiding

16 Oktober 2023