Interlogix TX-1510-01-1 Handleiding

Interlogix Deur-/raamsensor TX-1510-01-1

Lees hieronder de 📖 handleiding in het Nederlandse voor Interlogix TX-1510-01-1 (2 pagina's) in de categorie Deur-/raamsensor. Deze handleiding was nuttig voor 39 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

P/N - 466 2316 • REV D OCT12 1 •

DesignLine Recessed Door Contact Installation

Instructions

Introduction

This is the DesignLine Recessed Door Contact Installation

Instructions for model TX- - -1. The TX- - -1 is the 1510 01 1510 01

industry’s mos t flexible supervised, recessed door contact

allowing a multitude of applications while hiding the transmitter

within a door frame. The contact uses a replaceable lithium

battery and should last five years under normal usage.

The contact comes with a standard ﬂush-mount top and a

flanged top. Unscrew the top to access the battery or change

to a diﬀerent top.

Battery installation

To install the battery, do the following:

1. Unscrew the top of the contact.

2. Carefully pull the circuit board out (Figure 1 ) of the below

contact. Before removing the circuit board, notice that it

fits inside a channel on the inside of the case. Do not pull

the circuit board unit by the antenna wire.

Caution: You must be free of static electricity before handling

sensor circuit boards. Touch a grounded, bare metal surface

before touching circuit boards or wear a grounding strap.

Figure 1: Battery installation

3. Slide the battery onto the circuit board unit with the plus

(+) side up.

4. Slide the circuit board unit into the contact. Make sure you

slide it back into the channel guides for proper ﬁt with the

tamper switch facing up.

5. Screw the top back on the contact.

When replacing batteries, use only Panasonic Lithium CR23

batteries for replacement.

WARNING: The battery may explode if mistreated. Do not

recharge, disassemble, or dispose of in ﬁre.

Mounting

It is important to select the proper placement of the recessed

transmitter and magnet. The transmitter has two separate tops

that allow a flush mount or screw mount in case you accidently

over drill the hole or require extra support to ensure the

transmitter does not move. The magnet does not have a

second ﬂanged top so you must be careful to ensure that the

magnet is tightly in place once installed.

To mount the transmitter and magnet, do the following:

1. Install the CR2 battery if you have not already done so

(Figure 1 above ).

2. Select a location on the door frame for the TX- - -1510 01 1

transmitter and magnet to be installed (Figure 2 on page

2). Use a marker to mark the placement and ensure that

the two holes you intend to drill are lined up directly across

from each other.

Tamper

sw itch

Antenna

Contact

Battery

Circuit

board

2 DesignLine Recessed Door Contact Installation Instructions

Figure 2: Mounting

Note: This is only one mounting option. You should select

the best mounting method based on the application.

3. Using an 7/8 in. drill bit, slowly drill the first hole for the

magnet. The TX- - -1 was speciﬁcally designed to 1510 01

be slightly larger than an 7/8 in. hole so you will need to

carefully drill to ﬁt by slowly routing the hole little by little to

ensure a snug ﬁt.

4. Using a 7/8 in. drill bit, drill the mating hole for the

transmitter and use either the standard flush-mount cap

and insert the transmitter for a snug ﬁt, or use the flanged

cap and use the screws provided to mount the transmitter

to the door frame.

Enrolling

The following section describes general guidelines for

programming (learning) the sensor into the panel’s memory.

Refer to you panel documentation for complete programming

details.

To program (learn) the contact into the panel, do the following:

1. Unscrew the top of the contact.

2. Set the panel into program mode.

3. Refer to your panel documentation for instructions for

learning sensors.

4. Press and release the tamper switch on the top of the

contact circuit board (Figure 1 on page 1)until the panel

responds.

5. Replace the contact top.

6. Exit program mode.

Specifications

Battery

CR2032, 3 VDC, 225 mAh, Lithium Coin Cell

Typical battery life

5 to 8 years

Transmitter frequency

319.508 MHz (crystal-controlled)

Transmitter frequency

tolerance

± 8 kHz

Bandw idth

24 kHz

Modulation type

Amplitude shift key (ASK)

Unique ID codes

16 million

Peak field strength

Typical 35,000 uV/m at 3 m

Supervisory interval

64 minutes

Operating temperature

10 to 120°F (-12 to 49°C)

Enclosure

PC- 540

Weight

0.63 oz. (18 g)

Dimensions (L x W x

1.70 x 1.10 x 0.91 in. (4.32 x 2.76 x 2.32 cm)

Color

Belgian gray

Regulatory information

FCC compliance

This device complies w ith part 15 of the FCC

rules. Operation is subject to the follow ing

conditions:

1. This device may not cause harmful

interference.

2. This device must accept any interference

received, including interference that may cause

undesired operation.

Changes or modifications not expressly approved

by the party responsible for compliance could

void the user’s authority to operate the

equipment.

FCC ID: B4Z- - - TX 1510 01

Industry Canada ID: 1175C-TX151001

Contact information

www.utcfireandsecurity.com or www.interlogix.com

For customer support, see www.interlogix.com/customer-

support

Interlogix is part of UTC Climate Controls & Security, a unit of

Product specificaties

Merk:	Interlogix
Categorie:	Deur-/raamsensor
Model:	TX-1510-01-1
Kleur van het product:	Grijs
Gewicht:	12.9 g
Breedte:	39.2 mm
Diepte:	22.1 mm
Gebruikershandleiding:	Ja
Connectiviteitstechnologie:	Draadloos
Ondersteund aantal accu's/batterijen:	1
Certificering:	FCC
Frequentie:	319.508 MHz
Omgevingstemperatuur (min):	-12 °C
Omgevingstemperatuur (max):	49 °C
Aantal producten inbegrepen:	1 stuk(s)
Batterijtechnologie:	Lithium
Type batterij:	CR2032