Interlogix ShatterPro 3 Handleiding

Interlogix Deur-/raamsensor ShatterPro 3

Lees hieronder de 📖 handleiding in het Nederlandse voor Interlogix ShatterPro 3 (4 pagina's) in de categorie Deur-/raamsensor. Deze handleiding was nuttig voor 45 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

ShatterPro 3 Glassbreak Detector Installation Instructions

Introduction

This is the ShatterPro 3 Glassbreak Detector Installation

Instructions. The ShatterPro 3 is an acoustic glassbreak

detector designed to detect breaking glass from framed

windows in the perimeter of a building. The detector is

mounted in the building interior and uses a power supply from

a 12 VDC control panel. The detector is available in either a

low-profile round housing or a rectangular housing that

connects easily to a single-gang box (Figure 1 below).

Figure 1: ShatterPro 3 housings

The detector provides the following features:

Range up to 25 ft. (7.6 m)

Internal spring clip allows optimized room size coverage.

Alarm memory

After an alarm and until power is cycled, the alarm memory can

be checked with the hand-clap test.

LED indicator

Red LED provides detector test and status indication.

Tamper resistant

The detector has a screw that secures the cover to the base to

prevent tampering.

Hand-clap test

In addition to a test mode, you can test the detector by

clapping your hands.

Optional tamper switch

Sends a signal to the control panel when the cover is removed

from the base.

You will need the following tools and parts to install the

detector:

• ShatterPro 3 detector including cover screw

• Screws and wall anchors

• Flat-blade screwdriver

• Phillips screwdriver

• UTC Fire & Security 5709C hand-held tester

Mounting location

You can mount the detector on ceilings or on the walls

opposite or adjacent to the window to be protected (Figure 2

below).

Figure 2: Mounting locations

Ceiling

mount

Wall

mount

25' (7.6 m)

max.

25' (7.6 m)

max.

Use the following guidelines to determine the best mounting

location:

• Mount the detector at least 3 ft. (1 m) from the windows

being protected.

• Windows must be at least 12 x 24 in. (30.5 x 61 cm).

• Avoid locations where insulating, sound deadening, or

lined drapes or closed wooden shutters are used.

• Mount 12 in. (30.5 cm) away from wall corners.

• Locate in a suitable environment: temperature between 32

and 122°F (0 and 50°C); and humidity between 10 and

90% noncondensing.

P/N 1030856 • REV E • 21APR11 1

• Mount the detector on a stable surface up to 25 ft. (7.6 m)

from the farthest point on the glass surface.

• Avoid locations that expose the detector to possible false

alarm sources such as:

• Glass airlocks and vestibule areas

• Kitchens

• Residential car garages

• Small utility rooms

• Stairwells

• Bathrooms

• Small acoustically live rooms

• Air vents

Multiple window coverage

The detector has a 360 degree coverage pattern that can be

used to cover several windows in a single room. To use this

coverage pattern, do the following:

1. Draw an imaginary line from the center of each window to

be covered in toward the center of the room.

2. Mount the detector on the ceiling as close as possible to

where the lines intersect (Figure 3 below).

Figure 3: Multiple window coverage

Ceiling

mount

Detector

60 max.

Do not mount the detector at more than a 60 degree angle

from the center of any window to be protected.

Installation

All wiring must conform to the National Electric Code (NEC)

and/or local codes having jurisdiction.

Caution: If you are unsure about location, connect a 9V

battery to the detector and test it before permanently mounting

the detector.

To install the detector, do the following:

1. Run the security system wiring to the detector location.

2. Remove the front cover of the detector as follows:

Round housing

Press the release tab on the lip of the base, twist the cover

counter clockwise, and lift the cover off (Figure 4 below).

Figure 4: Round housing parts

Microphone

LED

Release tab

Rectangle housing

Insert a flat-blade screwdriver into the slot on the bottom of the

cover and gently pry up to unlock the cover. Grasp the bottom

of the cover and lift up until the cover plate is in the open

position (Figure 5 below).

Figure 5: Detector knockout locations

J3 Spring clip

Knockouts

J3 Spring clip

Slot

Knockouts

3. Set the range with J3 spring clip on the circuit board. See

“Range settings” on page 3.

4. Remove the appropriate wiring and mounting knockout

holes from the base. See Figure 5 above for rectangle

housings and round housings.

5. Pull the wires through the knockout holes and use two

screws to attach the base to the surface. Use wall anchors

if necessary.

6. Strip 3/8 in. of insulation from each wire.

7. Connect the system wires to the appropriate screw

terminals on the base and tighten the screws (Figure 6 on

page 3).

2 ShatterPro 3 Glassbreak Detector Installation Instructions

Figure 6: Wiring diagram

GND +12V N.C. COM N.O. T AMP TAMP

GND +12V N.C. COM

J3 Spring clip

Tamper Switch

Models:

5812NT

R5812NT

Models:

5815NT

R5815NT

8. Replace the cover as follows:

Rectangle housing

Press the cover back down over the detector until the

cover snaps firmly into place.

Round housing

Line up the tabs on the base with the corresponding tabs

on the cover, press together and turn clockwise until the

cover snaps firmly into place (Figure 7 below).

Figure 7: Attaching the round cover

9. Apply power. The red LED should flash once.

10. Test the detector. See “Testing” below.

Range settings

The detector has a spring clip (J3) to set the room size

( Figure 6 above). Use Table 1 below to determine what setting

to use for your application

Table 1: Setting the range

Setting Description

Open Default. Use for rooms 100 square ft. and larger, Range

5 to 25 ft (1.5 to 7.5 m).

Closed Use for rooms smaller than 100 square ft. Range 3 to 10

ft. (0.9 to 3 m).

Testing

To verify detector range and operation, you need the UTC Fire

& Security 5709C handheld tester.

To test the detector, do the following:

1. Set the tester to the appropriate glass-type setting. Use

the tempered setting if you are unsure about the glass

type.

2. To put the detector in test mode, hold the tester so that the

speaker is within 1 in. (25 mm) of the detector microphone

( Figure 8 below) and activate the tester. When the

detector is in test mode the LED on the detector lights

steady for 4 seconds and then flashes for 60 seconds. The

relay opens for 4 seconds, then returns to standby. Time

resets after each valid test.

Figure 8: Using the tester

• le Sing

• Co nt

in uo

usPla

te •

p eer

d •

Lam in a dte •

Bat te ry LED

t t

ery is O iK f LED

st a ys on

in g

t e

709

Shatt e r

S ieer s T

t e r

se f or

t e stin g :

Shatt erPr

Sha rtt e

box

Sha

t e rbox II

Sha e rt t Swi t c

SEN

TRO

When the detector is in test mode,

the LED lights steady for 4 seconds,

then flashes for 60 seconds. Time

resets after each valid test.

1” (2.54 cm)

Hold the tester so that the speaker is

within 1” of the detector microphone.

3. Hold the tester near the surface of the glass to be

protected and aim the speaker at the detector. Be sure the

tester is at the point on the glass farthest from the

detector. If closed drapes or curtains are present, hold the

tester behind them (Figure 9 below).

Figure 9: Testing behind curtains

4. Press the test button on the tester. The LED on the

detector should stay on for 4 seconds to indicate the glass

ShatterPro 3 Glassbreak Detector Installation Instructions 3

Product specificaties

Merk:	Interlogix
Categorie:	Deur-/raamsensor
Model:	ShatterPro 3
Kleur van het product:	Wit
Breedte:	102 mm
Diepte:	102 mm
Hoogte:	21 mm
Gebruikershandleiding:	Ja
Voeding, voltage ingang:	16 V
Aantal producten inbegrepen:	1 stuk(s)