Ibanez SA360QM Handleiding

Ibanez Gitaar SA360QM

Lees hieronder de 📖 handleiding in het Nederlandse voor Ibanez SA360QM (2 pagina's) in de categorie Gitaar. Deze handleiding was nuttig voor 28 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

INSTRUCTION MANUAL

• E L E C T R I C G U I T A R S •

w i t h L O C K I N G S Y S T E M

E L E C T R O N I C S

SWITCH FUNCTIONS

Ibanez Instruments are unique in the simplicity and versatility of our

switching systems. Each model was designed to allow the maximum

amount of useful pickup positions with the simplest operations.

Neck Center Bridge

RG, S, JEM, UV : Split-5 RG, S : Classic-5

Neck Center Bridge

JS900 : Standard-3

Neck Center Bridge

JS1000

Humbucking is parallel connected.

JS1000 : HIGH PASS FILTER SWITCH

The push/pull switch on the volume control in

the up position engages the high pass filter

system. This setting allows the volume to be

rolled back without losing the high frequencies.

CONTROLS

Tone

Volume

5way Pickup Selecter

Volume

w/High Pass On/Off Sw.

3way Pickup Selecter

Tone

w/Coil Tap On/Off Sw.

5way Pickup Selecter

Volume

1V, 1T JS1000

PGM

does not work when Coil Tap Sw. is “ON”

This is to certify that the aforementioned equipments fully conform to

protection requirements of the following EC council directives.

DIRECTIVES : 89/336/EEC Electromagnetic compatibility

DISTRIBUTED BY

B R I D G E I N F O R M A T I O N

STRING GAUGES

All guitars are set up at the factory with light gauge 009”- 042” strings

(7-string 009”- 054”). Different gauges of strings can result in the need

for string height, neck curvature, tremolo spring and intonation

readjustments.

Ibanez guitars feature four styles of locking tremolos. To identify which

tremolo is used on your guitar, locate the logo stamped either on the

bridge plate or the bridge tremolo block.

*Both Lo-Pro Edge and Edge tremolos have the “Edge” logo on the tremolo blocks.

*Adjustment of the 7-string tremolo is the same as the corresponding 6-string tremolo.

ADJUSTMENT

Lo-Pro Edge / Edge / Lo-TRS / TRS101

In the case of locking tremolos, replace the

strings one by one. Removing all the old

strings at once will release the tension on

the tremolo and change the tremolo angle

“up-pull.” Loosen the Pressure pad screw

(D) on the locking nut and loosen the string

to be replaced. Loosen the String stopper

screw (F) and remove the string from the

saddle. Cut off the ball end of new string as shown on the illustration and

insert the cut side of new string between the saddle and the String

holder block. Tighten the String stopper screw (F) and tune the string.

After checking the intonation, tighten the Pressure pad screw (D) on the

locking nut.

TRS505

In the case of TRS505 tremolo, replace the strings one by one. Removing

all the old strings at once will release the tension on the tremolo and

change the tremolo angle “up-pull.”

Loosen the Pressure pad screw (D) on the

locking nut and loosen the string to be

replaced. Remove the string through the

String holder hook (G). Thread new string

through the String holder hook (G) and tune

it. After checking the intonation, tighten the

Pressure pad screw (D) on the locking nut.

The tremolo springs adjust the tremolo

angle by tightening or loosening the tremolo

tension. To adjust tremolo angle, locate the

adjustment screws in the rear tremolo

cavity. The tremolo system when in tune

should sit parallel to the surface of the

guitar.

If the tremolo system is not sitting parallel to

the surfac e of the guitar, remove the

tremolo cavity cover plate and tighten the

Tremolo tension adjustment screws (H) if the tremolo is forward dumped.

Loosen the screws (H) if the tremolo is up-

pulled. Retune the strings to the proper pitch

and check the angle.

Edge and Lo-Pro Edge tremolos have the

Block Lock System to lock the tremolo springs

on the tremolo block. Remove the Block Lock

when replacing the springs. Choose the

number and placement of the tremolo springs

according to the string gauge and the tremolo

angle as follows.

Loosen the Pressure pad screw (D) on the locking nut and loosen the

string to be adjusted. Loosen the Saddle lock screws (E) on the saddle to

be adjusted and adjust the saddle forward or backward.

Tighten the Saddle lock screw (E) and tune the string. After rechecking

the intonation, tighten the Pressure pad screw (D).

On the base plate there are two holes for each Saddle lock screw (C).

These allow the user to change string gauges while allowing the

maximum saddle movement. If the intonation cannot be adjusted

because the saddle needs to be set back further, remove the intonation

screw and insert it into the hole located further back on the bridge plate.

LO-TRS

LO-PRO EDGE

(B) (E)

(A) (F)

LOCKING NUT (D)

TREMOLO ARM

Edge / Lo-Pro Edge

The tremolo arm can be inserted and removed very

easily. Insert the tremolo arm into the arm socket

and firmly push down until the arm snaps into

place. Both bushings should be completely hidden.

The rotation torque of the arm can be adjusted by

removing the bushings. To

further reduce the torque,

remove both bushings. To

replace the bushings, open

the new bushings at the split section and snap

them into place on the arm.

*After some time and use, it may impossible to secure

the arm even when both bushings are in place. If this

happens, replace the arm bushings with new ones.

Lo-TRS / TRS101 / TRS505

Insert the tremolo arm into the arm socket

and turn it clockwise until it stops. The

rotation torque of the arm can be adjusted by

turning the arm counterclockwise.

Lo-TRS and TRS tremolos are equipped with

a arm stop position screw located on the

bottom of the tremolo block and can be

adjusted by tightening the screw.

FINE TUNING

After locking the top lock, fine tuning the instrument can be done by

turning the fine tuning screws (A).

*To allow maximum fine tuning adjustment, it is recommended that the fine tuners be

set to the middle position before locking the nut.

STRING HEIGHT

The height adjustment of the tremolo can be raised or

lowered by adjusting the pivot studs(B) that the tremolo

mounts on. These are located at either side of the front

of the bridge. Clockwise lowers the tremolo and counter

clockwise raises the tremolo.

In the case of Edge and Lo-Pro Edge tremolos, the

Pivot studs(B) are locked internally by the Stud lock

screws(C). Always loosen the Stud lock screws (C)

before tightening the Pivot studs(B). After adjusting the

string height, tighten the Stud lock screws(C).

INTONATION

REPLACING THE STRINGS

TREMOLO SPRING

(A)

(B) (E)

TRS505

(B) (E)

(A)

(F)

TRS101

EDGE

(B/C) (E)

(A) (F)

(B/C) (E)

(A)

(F)

(C)

(G)

(H)

(H) (H)

Product specificaties

Merk:	Ibanez
Categorie:	Gitaar
Model:	SA360QM
Kleur van het product:	Rood
Soort:	Elektrische gitaar
Interface:	6.3mm
Bereik:	Standaard
Fret type:	Standaard
Nektype:	Aanschroefbaar
Toetsradius:	400 mm
Schaalgrootte:	648 mm
Frets hoeveelheid:	22
Toetsmateriaal:	Rozenhout
Behendigheid:	Rechts
Nekmateriaal:	Esdoorn
Nootbreedte:	43 mm
Voorvolume controle:	Ja
Snoerkwantiteit:	6 snaren
Bovenkant materiaal:	Mahonie
Machinekop materiaal:	Verchroomd messing