HQ EL-PIRLA80 Handleiding

HQ Bewegingsdetector EL-PIRLA80

Lees hieronder de 📖 handleiding in het Nederlandse voor HQ EL-PIRLA80 (66 pagina's) in de categorie Bewegingsdetector. Deze handleiding was nuttig voor 35 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/66

EL-PIR80

Radar sensor light

The sensor light has an active motion detector, the integrated HF sensor emits high-

frequency electro-magnetic wave (5.8GHz) and receives their echo. The sensor

detects the change in echo from even the slightest movement in the light’s detection

zone. A microprocessor then triggers the “switch light ON” command. Detection is

possible through doors, panes of glass or thin walls.

Detection zones for ceiling mounting

1) Minimum reach 1m dia.

2) Maximum reach 8m dia.

Detection zones for wall mounting

3) Minimum reach 1m dia.

4) Maximum reach 8m dia.

Important: persons or objects moving towards the light are detected best!

Installation procedures

1. Take down the glass shade by turning it anti-clockwise (see g.1)

2. Hold base against the wall and mark drill holes, paying attention to any existing

wiring in the wall;

3. Drill the holes, insert wall plugs (6mm dia);

4. Put the power wire and load wire through the base holes;

5. Screw the base into place (see g. 2);

6. Connect the mains power supply and the load wire to the connection terminal

according to connection-wire mark.

7. Adjust knob to setting;

8. Fit glass shade and turn it clockwise (see g. 3).

Technical specications

Wattage: 60W/E27

Power supply: 220-240V~, 50/60Hz

Installation sit: indoors, wall/ceiling mounting

HF system: 5.8GHz CW radar, ISM band

Transmission power: <10mW

Detection angle: 360°, 160°

Reach: 1-8m (dia.), adjustable

Time setting: 5sec to 15min

Light control: 2~2000LUX

Power consumption: approx.0.9W

Connection illumination

connect N, L with power;

Reach setting (sensitivity)

Reach is the term used to describe the diameter of the more or less

circular detection zone produced on the ground after mounting the

sensorlight at a height of 2.5m, turn the reach control fully anticlockwise

to select minimum reach (approx.1 m dia), and fully clockwise to select

maximum reach (approx. 8m dia).

Time setting

The light can be set to stay ON for any period of time between approx.

5sec(turn fully anticlockwise) and a maximum of 15min(turn fully

clockwise). Any movement detected before this time elapse will re-start

the timer. It is recommended to select the shortest time for adjusting the

detection zone and for performing the walk test.

NOTE: after the light switches OFF, it takes approx. 1sec before it is able to start

detecting movement again. The light will only switch on in response to movement

once this period has elapsed.

Light-control setting

The chosen light response threshold can be innitely from approx. 2-

2000lux. Turn it fully anti-clockwise to select dusk- to-dawn operation at

about 2 lux. Turn it fully clockwise to select daylight operation at about

2000lux. The knob must be turned fully clockwise when adjusting the

detection zone and performing the walk test in daylight.

SENS TIME LUX

SENS

TIME

LUX

Product specificaties

Merk:	HQ
Categorie:	Bewegingsdetector
Model:	EL-PIRLA80
Kleur van het product:	Wit
Gewicht verpakking:	1580 g
Connectiviteitstechnologie:	Draadloos
Montagewijze:	Plafond
Afmetingen verpakking (BxDxH):	320 x 320 x 125 mm
Ingangsspanning:	220 - 240 V
Maximumbereik:	8 m
Frequentie:	5.8 MHz
Afmetingen (B x D x H):	300 x 300 x 110 mm
Bedrijfstemperatuur (T-T):	0 - 40 °C