Henry Engineering LogiConverter Handleiding


Lees hieronder de đź“– handleiding in het Nederlandse voor Henry Engineering LogiConverter (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 5 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
LOGICONVERTER
HENRY ENGINEERING
503 Key Vista Drive
Sierra Madre, CA 91024
tel: 626.355.3656
fax: 626.355.0077
website: www.henryeng.com
UTILITY CONTROL INTERFACE
DESCRIPTION
LogiConverter is a logic interface unit that facilitates control of studio, AV, and similar equipment. LogiConverter creates
isolated SPST relay outputs from opto-isolated logic-level input signals. Four channels of interface are provided. They can
operate independently (for “start-only” use) or in pairs (for “start-stop” use). Each channel can be user-programmed to
generate momentary or maintained relay closure outputs, with several modes of input control.
INSTALLATION
Connection to the four LogiConverter inputs is via the 15-pin D connector. All inputs are opto-isolated. Input voltages
should be between 5 and 24 VDC. For connection to external contact closures, or equipment that provides “open
collector” (ground-sink) interface, connect the + input to any +12V terminal. Connect the – input to the open collector, and
connect any LogiConverter GND pin to the emitter.
Connection to the LogiConverter relay outputs is via plug-in terminal blocks. Remove about 1/8” of insulation, insert wires
into the connector, and tighten the screws. Be sure that no bare wiring is exposed.
PROGRAMMING
LogiConverter has 24 possible modes of operation….read carefully!
The four input/output channels can operate independently (“start-only”) or in pairs (“start-stop”, or “set-reset”).
If start-stop operation is selected, channels 1 & 2 are paired, and channels 3 & 4 are paired. The various modes are
programmed using the 8 dip switches, SW1 thru SW8, accessible from the front of the unit. They function as follows:
SW1 Selects input mode of Chan. 1 SW5 Selects input mode of Chan. 3
SW2 Selects input mode of Chan. 2 SW6 Selects input mode of Chan. 4
SW3 Selects output mode of Chan. 1 SW7 Selects output mode of Chan. 3
SW4 Selects output mode of Chan. 2 SW8 Selects output mode of Chan. 4
SW1 thru SW4 affect channels 1 & 2; SW5 thru SW8 affect channels 3 & 4 in the same ways.
Each channel has an “input mode” switch. Since channels 1 & 2 can operate as a pair, these switches affect both inputs.
For independent (“start-only”) operation, both SW1 and SW2 must be OFF . An input at Chan. 1 will produce an output at
Chan. 1. An input at Chan. 2 will produce an output at Chan. 2. There is no interaction.
There are two modes of paired (“start-stop”) operation: non-latching and latching. If non-latching operation is selected, an
input at Chan. 1 will cause an output at Chan. 1. Removing the input from Chan. 1 will cause an output at Chan. 2. This
mode is recommended for maintained (continuous) input signals only. To select this mode, SW1 should be OFF, and
SW2 should be ON. (The Chan. 2 input is not used in this mode.)
If latching operation is programmed, an input at Chan. 1 will cause an output at Chan. 1. Additional inputs to Chan. 1 will
produce no output; an input to Chan 2 must be applied to reset the latch, which will also cause an output on Chan. 2. To
select this mode, both SW1 and SW2 must be ON. (SW5 and SW6 have the same effects on input channels 3 and 4.)
Each channel has an output mode switch. If SW3 is OFF, the Chan 1. output will be a momentary closure (pulse). If SW3
is ON, the relay closure will be maintained for the duration of the input signal. SW4 affects Chan. 2 in the same way, as
does SW7 for Chan. 3 and SW8 for Chan. 4.
D CONNECTOR PIN-OUTS FOR INPUT WIRING
PIN 1 Input 1, + PIN 7 Input 4, + PIN 13 +12V
PIN 2 Input 1, - PIN 8 Input 4, - PIN 14 GND
PIN 3 Input 2, + PIN 9 +12V PIN 15 +12V
PIN 4 Input 2, - PIN 10 GND
PIN 5 Input 3, + PIN 11 +12V All inputs: 5 to 24 VDC,
PIN 6 Input 3, - PIN 12 GND 200 ms minimum length
5
5
4
4
3
3
2
D
C
B
A
230V
115V
BLK PRI SEC
GRN
WHT
2
+
+
-
-
1
+
3
-
4
-
+
CONTROL INPUTS
GND
GND
GND
+12V
+12V
+12V
+12V
+12V
+12V
+12V
+12V
+12V
+12V
+12V
+12V
+12V
+12V
+12V +12V
R12
10K
R22
1MEG
R2
10K
+
C5
1000uF 25V
R18 1.5K
SW1E
5 12
+
C1 3.3u
E7
E1
R21
1MEG
U3
4N25
1 6
2
5
4
R11
10K
TP2
1
+
C2 3.3u
SW1F
6 11
E8
E2
U4
4N25
1 6
2
5
4
LED5
R24
1MEG
SW1B
2 15
U2
4N25
1 6
2
5
4
R9
10K
TP1
1
SW1G
7 1
+
C3 3.3u
C6
.1uF 50V
SW1C
3 1
U5D
CD4011B
12
13 11
R17 1.5K
U5B
CD4011B
5
6
4
U5A
CD4011B
1
2
3
SW1A
1 16
D6
1N4004
SW1H
8 9
R1
10K
R4
10K
R23
1MEG
+
C4 3.3uF
R20 1.5K
E5
F1
115V: 250 ma; 230V: 125ma
R19 1.5K
U5C
CD4011B
8
9
10
T1
SPW-102
1
3
4
2
5
6
8
7
J3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
SW1D
4 1
R3
10K
R29
1.5K
R10
10K
U1
4N25
1 6
2
5
4
E6
D5
1N4004


Product specificaties

Merk: Henry Engineering
Categorie: Niet gecategoriseerd
Model: LogiConverter

Heb je hulp nodig?

Als je hulp nodig hebt met Henry Engineering LogiConverter stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Henry Engineering

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd