Heatit Z-DIN 616 Handleiding

Heatit Niet gecategoriseerd Z-DIN 616

Lees hieronder de 📖 handleiding in het Nederlandse voor Heatit Z-DIN 616 (12 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 65 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/12

TABLE OF CONTENTS

1 Introduction

2 Behavior within the Z-Wave network

3 Installation

3.1 Relay outputs

3.2 Inputs

4 Factory reset

5 Adding the Heatit Z-DIN 616 to the Z-Wave network

6 Associations

6.1 Association groups

7 Conﬁguration parameters

8 Command classes

8.1 Supported command classes

8.2 Controlled command classes

9 Technical documentation

HEATIT

Z-DIN 616 Ver 2021-A

Firmware 0.15

01.02.2021

Installers manual

1. INTRODUCTION

The Heatit Z-DIN 616, which is built upon the wireless Z-Wave

communication protocol, has 6 relay driven outputs and 6 digital

inputs. The unit is a multi-purpose Z-Wave I/O module, which can be

used for many applications. For example, the Heatit Z-DIN 616 provides

the possibility to control other systems via the Z-Wave network, by

utilizing the 6 outputs as a kind of hand-over function to another

automation system.

The relay outputs (controlled through the Z-Wave network) are suitable

for switching up to six 230VAC loads. In connection with simultaneous

connection to SELV (Safety Extra Low Voltage) and 230VAC power

circuits for relay outputs, relays must be considered as two groups,

where the ﬁrst group includes output 1 to 3 and the second group

includes outputs 4 to 6. This ensures complete separation between

the SELV and 230VAC circuits. If one of the relays in the group is

connected to a SELV circuit, the remaining outputs are not allowed to

be connected to 230VAC or another circuit which is not a SELV circuit.

For example, the relay outputs of the Heatit Z-DIN 616 module can be

used to control the 230Vac power supply outlet, making it possible

to turn on and disconnect the electrical outlets directly through the

Z-Wave network. For safety reasons, however, it is not recommended

to use the Heatit Z-DIN 616 to connect electrical outlets that are

normally used for hazardous tools and machinery.

The 6 digital inputs of the Heatit Z-DIN 616 are useful for various

purposes, where potential-free contacts or Open Collector outputs

may be connected. The inputs may be conﬁgured to diﬀerent trigger

modes; leading edge, trailing edge or level triggered. The Heatit Z-DIN

616’s inputs may be programmed to control other Z-Wave devices

when the inputs are activated, by sending Z-Wave commands over the

Z-Wave network to e.g. Z-Wave relay modules, dimmer units etc.

Heatit Z-DIN 616 allows sending diﬀerent types of Z-Wave commands

by utilizing the diﬀerent association groups for the 6 inputs. In addition,

the Heatit Z-DIN 616 also acts as a repeater, thus extending the range

of the Z-Wave network. By default, the Heatit Z-DIN 616’s inputs and

outputs are set to operate as toggle-relays. Input 1 controls the output

1, input 2 controls the output 2, etc. This functionality can be modiﬁed

via the conﬁguration parameters 3-8 and 13-18.

2. BEHAVIOR WITHIN THE Z-WAVE™ NETWORK

This device may be operated within any Z-Wave network with

Z-Wave-certiﬁed devices from other manufacturers. All non-battery-

operated nodes within the network will act as repeaters regardless of

manufacturer to increase the reliability of the network. On delivery, the

device does not belong to any Z-Wave network.

The device needs to be added to an existing network to communicate

with the other devices within it. Devices may also be removed from

a network. The add/remove processes are initiated by the primary

controller of the Z-Wave network.

3. INSTALLATION

Installation must be done by a qualiﬁed electrician in accordance with

the National Building codes. Before installation, disconnect any power

to the device mains. During installation of the device, power to the

device must be disconnected AT ALL TIMES!

The Heatit Z-DIN 616 must be connected to a 24 Volt AC or DC power

supply via the terminals labeled ”Vin”. The polarity is of no importance.

The supply must be dimensioned to allow the supplied module with

enough power to enable all relays to be activated. Regarding power

consumption: see the technical details section.

3.1 Relay outputs

The 6 outputs of the Heatit Z-DIN 616 module consist of 1-pole SPST

connectors (Single-Pole Single-Throw).

As default the outputs are conﬁgured to be controlled by its

corresponding input (output 1 is controlled by input 1, etc.). This

functionality is changeable via conﬁguration parameter 13 to 18.

3.2 Inputs

The digital inputs of the Heatit Z-DIN 616 module can be connected

to diﬀerent types of control signals - switches, relays, open-collector

outputs, etc.

The inputs IN1, IN2, IN3, IN4, IN5 and IN6 which operates as active low,

are pr. default pulled up to 3V DC and must be pulled low in order to

work, by mounting e.g. a contact between [IN1..IN6] and 0V. The inputs

24V AC/DC

230V AC

Vin Vin IN1 IN2 IN3 0V C

IN4 0V IN5 04

0V IN6 0V NO

Z-DIN 616

Belastning

NO C

Load

Product specificaties

Merk:	Heatit
Categorie:	Niet gecategoriseerd
Model:	Z-DIN 616
Kleur van het product:	Grey, Light grey
Certificering:	IP21, CE, EN 50491-3: 2009 EN 60669-2: 2004, EMC 2014/30/EU, RoHS 2011/65/EU, LVD 2014/35/EU
Afmetingen (B x D x H):	105 x 60 x 85 mm
Maximum indoorbereik:	40 m
Stroomverbruik (typisch):	0.6 W
Aantal polen:	1
DIN rail bevestiging:	Ja
AC-uitgangsvoltage:	250/360 V