Getac VR-X10 Handleiding

Getac Niet gecategoriseerd VR-X10

Lees hieronder de 📖 handleiding in het Nederlandse voor Getac VR-X10 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 14 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/2
VR-X10
DVR System
QUICK START GUIDE
VERETOS MVS
1.
Unpacking
VR-X10 DVR System
Terminal connector
for DC IN
Terminal connector
for GPIO x 2
D-sub to BNC cable Electrical wire x 3
Fuse tap (ignition) -5A 15A inline fuse
GPS antenna Wi-Fi/BT antenna x 2
Mounting kit (racket
and screw x 4)
Key x 2
2.
Identifying Components
Front Panel
No. Descriptions
HDD LED
- Green light: HDD activity
Security door LED
- Green light: Door locked
- Red light: Door unlocked
Recording LED
- Blue light: Video recording in progress
Power button: Press to power on VR-X10.
Power LED
- Red light (for 10 seconds): DC power-in
- Green light: Software ready
Door lock: Use the key/software to unlock
the door.
Security door: Protects the removable
storage inside (if existing). The door is
automatically locked when closed.
CFast connector: Allows the use of a CFast
card for removable storage.
USB 3.0 connector: Allows the use of an
USB disk for removable storage. (See
“Recommended USB Disks” on the reverse
side for more information.)
Rear Panel
No. Descriptions Remarks
802.3af PoE ports (1 to 4): Connects up to four IP
cameras. Each port has a status LED.
RJ45-type audio in connectors: Connects up to
two wireless microphones.
Wireless microphone model: WM-T2400M
Video capture connector: Provides 8-channel
composite video inputs and 4-channel audio
inputs.
DC-in connector: Connects to vehicle ignition and
battery with the 3 electrical wires provided.
See “DC-in Connector Pin Assignments” on
the reverse side for wiring information.
GPIO ports: Provides additional control lines.
There are 20 GPIO pins in two groups of 10 pins.
See “GPIO Connector Pin Assignments” on
the reverse side for wiring information.
RJ45 connectors (LAN 1 and LAN 2): Provides
10/100/1000 base-T Ethernet connection.
LAN 2 supports PXE.
GPS antenna connector
Wi-Fi/BT antenna connectors (Auxiliary and
Main)
Combo audio connector: Connects a headset
microphone.
USB 3.0 connector
USB 2.0 connectors (1 to 3)
Control unit connector: Connects to the CU-D50
control unit.
CU-D50 is an optional item.
Mini-HDMI connector: Connects to a monitor
supporting HDMI interface.
Mini DisplayPort: Connects to a monitor
supporting DisplayPort interface.
5 6 1 8 8 6 8 8 0 0 0 1 R 0 0
3.
References
Pin Assignments
DC-in Connector Pin Assignments
GPIO Connector Pin Assignments
Notes on GPIO:
Recommended USB Disks
The below USB disk models have been tested
as fully compatible with VR-X10.
SanDisk Ultra® USB 3.0 Flash Drive
Kingston DataTraveler G4
NOTE: See the figure at the right for the
USB disk size supported by VR-X10. Also, you
are advised to attach a lanyard to the USB
disk for easy removal of the disk.
More Information
See Installation Diagram for more information.
4.
Cautions and Notices
This equipment is designed for use and
installation in a vehicle. It can be mounted
in a vehicle’s center console or trunk.
Safety Cautions
This symbol (a lightning flash in a
triangle) is intended to alert the
user to the presence of uninsulated
voltage within the product’s enclosure
that can be high enough to constitute a
risk of electric shock to human bodies.
This symbol (an exclamation mark in
a triangle) is intended to alert the
user to the presence of important operating
and maintenance information in the
document(s) accompanying the product.
To reduce the risk of electric shock, do
not remove the cabinet cover. There are
no user-serviceable parts inside. Contact
qualified service personnel if servicing is
required.
Do not expose the equipment to rain or
moisture.
Keep the equipment away from risks of
dripping or splashing liquids.
Allow adequate ventilation around the
equipment. Do not cover or block any
ventilation openings.
Use the recommended accessories only.
Battery Cautions
There is danger of explosion or fire if the
battery is handled improperly.
Replace only with the same or specified
type.
Do not disassemble or dispose of in fire.
Do not store in temperatures above 60 C.
Use specified charger for rechargeable
batteries.
Do not recharge the battery if it is not a
rechargeable type.
Do not leave the battery in a vehicle
exposed to direct sunlight for a long period
of time with doors and windows closed.
For memory backup battery: There is danger
of explosion if the battery is incorrectly
replaced. Replace only with the same or
equivalent type. Consult qualified service
personnel when replacement is required.
FCC Regulations
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
To assure continued compliance, follow the
attached installation instructions and do
not make any unauthorized modifications.
FCC Note:
This equipment has been tested and found
to comply with the limits for a class A digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reason-
able protection against harmful interference
when the equipment is operated in a
commercial environment. This equipment
generates, uses, and can radiate radio
frequency energy, and if not installed and
used in accordance with the instruction
manual, may cause harmful interference to
radio communications. Operation of this
equipment in a residential area is likely to
cause harmful interference in which case
the user will be required to correct the
interference at his own expense.
Warning:
To assure continued FCC emission limit
compliance, the user must only use shielded
interface cables when connecting to external
units. Also, any unauthorized changes or
modifications to this equipment could void
the user's authority to operate this device.
50mm ~ 60mm
22mm (Max.)
11mm (Max.)
A1 A10
B1 B10
Example of a lanyard
A1 A2 A3 A4 A5 A6 A7 A8 A9 A10
GND +12V RS232 RX RS232 TX I/O Out 4 I/O Out 3 I/O In 8 I/O In 7 I/O In 6 I/O In 5
COM2
B1 B2 B3 B4 B5 B6 B7 B8 B9 B10
GND +12V RS232 RX RS232 TX I/O Out 2 I/O Out 1 I/O In 4 I/O In 3 I/O In 2 I/O In 1
COM1
1 2 3
Ignition Vehicle Battery+ Vehicle Battery-
Pins Low / High Active Input Voltage When using a digital/O device, you must ground the
device by connecting it to the metal part of the VR-X10
cabinet. This common return path is needed as the
reference point for high/low voltage measurement.
I/O In 1, 2, 5, 6 Low Active 0 V
I/O In 3, 4, 7, 8 High Active 6 V~24 V
Pins Battery Mode Output Voltage / Current
IO Out 1, 2, 3, 4 Vehicle Battery Mode Vehicle Battery Voltage / 0.75 A
VR-X10 Internal Battery Mode 6.3 V~8.4 V / 0.75 A
1 2 3

Product specificaties

Merk: Getac
Categorie: Niet gecategoriseerd
Model: VR-X10

Heb je hulp nodig?

Als je hulp nodig hebt met Getac VR-X10 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Getac

Getac

Getac VD-01 Handleiding

20 Augustus 2024
Getac

Getac Veretos BC-01 Handleiding

31 Juli 2024
Getac

Getac BC-03 Handleiding

31 Juli 2024
Getac

Getac BC-4K Handleiding

31 Juli 2024
Getac

Getac VR-X10 Handleiding

31 Juli 2024
Getac

Getac VR-X20 Handleiding

31 Juli 2024
Getac

Getac CU-D50 Handleiding

25 Juli 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Axler

Axler Hammerhead Pro Follow Focus Handleiding

19 December 2024
Axler

Axler Hammerhead Follow Focus Handleiding

19 December 2024
Cosatto

Cosatto Giggle 4 Handleiding

19 December 2024
Yamazen

Yamazen LCR-80-FSET Handleiding

19 December 2024
Asus

Asus EBS-P300 Handleiding

18 December 2024
QSC

QSC AcousticDesign AD-C245C Handleiding

18 December 2024
Asus

Asus ZenWiFi ET9 Handleiding

18 December 2024
Asus

Asus NUC 12 Extreme Compute Element Handleiding

18 December 2024
Asus

Asus NUC 11 Extreme Kit Handleiding

18 December 2024
Asus

Asus NUC 12 Pro X Kit Handleiding

18 December 2024