Genelec S360A Handleiding


Lees hieronder de đź“– handleiding in het Nederlandse voor Genelec S360A (12 pagina's) in de categorie Monitor. Deze handleiding was nuttig voor 38 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/12
S360A
Smart Active Monitor
Operating Manual
2
Introduction
Congratulations and a thank you for the purchase of a
Genelec Smart Active Monitor™ (SAM™) system. This manual
addresses the stand-alone setup and use of the S360A monitor.
SAM monitors can also be set up from a Mac or a PC using
the Genelec Loudspeaker Manager GLM™ and the proprietary
Genelec monitor control network, offering much more versatile
acoustic settings and features. Please find more details in the
separate GLM Operating Manual.
Housed in a compact, low diffraction enclosure with premium
quality Finnish woodwork, the S360A features a further enhanced
10-inch high efficiency and minimal distortion woofer based on
Genelec’s Master Series, and an integrated extended Directivity
Control Waveguide DCW TM supporting its 1-inch compression
driver. A thirty-two mm (1 ÂĽ in) thick front baffle and critical
bracing minimise panel vibration for pristine sound quality.
The S360A is a precision monitor with neutral and well-controlled
sound characteristics on its acoustical axis, uncoloured off-axis
response, and 95-degree (horizontal) to 75-degree (vertical)
dispersion for accurate directivity control across the entire
audio band. Like other new SAM monitors, it features constant
acoustic group delay above the lowest octaves, i.e. linear
phase response, without introducing latency incompatible with
production requirements.
The S360A’s fusion of high SPL and compact size makes it
perfect for demanding film, post and music production, including
play-live monitoring. In combination with a subwoofer, the
S360A satisfies the demands of premium home theatres, EDM
playback or Dolby film mixing even in rooms where the listening
distance exceeds 10 metres (33 feet). Due to well-controlled
dispersion, S360 may also be used in midfield or even nearfield
applications. If doing so, please be sure first to read the Safe
listening practice paragraph in this manual.
The S360A provides two pairs of enclosure mounting points,
and its integrated system electronics can be placed remotely
using the 2U high rack installation kit. Versatile mounting is
further supported by downward-firing flow optimised laminar
integrated reflex ports LIPTM, also making it suitable for use in
conjunction with perforated screens. To focus low frequency
output while preventing vibration transfer and air turbulence,
S360A includes an innovative Iso-Plate TM, which effectively
decouples the monitor from its base when standing. Tailor-made
S360A mounting brackets for wall, ceiling, stand and truss
installation may be acquired separately.
Package content
The package contains
• one S360A monitor
• one mains cable, length 1.8 m (6 ft)
• one 5 m GLM network cable
• this operating manual
System setup using GLM Control Network
Although S360A can be used without the GLM software and
control network, it can only reach its full potential when set up
and calibrated using the GLM software. Genelec recommends
setting up SAM monitoring systems using the GLM application.
Please find a more detailed description of the setup and use in
the separate GLM System Operating Manual.
The GLM software can be downloaded at www.genelec.com
free of charge. The necessary hardware for creating the control
network - GLM Kit (order number 8300-601) - is sold separately
at your Genelec dealer. The main components of the kit are the
calibrated measuring microphone and the GLM Adapter, which
links the computer running the software, measuring microphone
and all monitors and subwoofers together.
Genelec Loudspeaker Manager GLM and the proprietary Genelec
monitor control network offer automated acoustic equalization,
alignment and level calibration for any reproduction system from
simple stereo to very complex 3D immersive audio setups including
also one or more subwoofers. GLM setup is fast and accurate.
Settings can be controlled with a Mac or PC or they can be
permanently stored in the monitors to make them available at all
times, even when a computer is not connected.
3
The setup is fast and consists of the following steps:
1. Connect a CAT5 (RJ45) or higher category cable between
each monitor (and subwoofer) and finally to the control
network input of the GLM Adapter device (see Figure 1).
2. Connect the GLM Adapter device to computer USB
connector.
3. Using a microphone stand, place the Genelec measurement
microphone at the listening location with the microphone
pointing upwards and the microphone top at the height of
the engineer’s ear. The microphone is a part of the GLM
User Kit.
4. Connect the microphone cable to the microphone input in
the GLM Adapter device.
5. Download the GLM software at the Genelec web site (www.
genelec.com).
6. Install the GLM software and follow the instructions in the
software to measure and set up your monitors.
7. If you plan to not use a computer for controlling the
monitors, use the GLM software to write the setting into the
monitors (use menu item “Group | Store Group Settings”).
GLM calculates the acoustic compensation for the room in a
cloud computer. This enables always up-to-date methods and
efficient calculation process. The Stored Settings function using
the Genelec Loudspeaker Manager software can be used to
store calibration settings into the monitors.
Once the GLM network is disconnected, the calibrated stored
settings using the Genelec Loudspeaker Manager software can
be selected in use by setting the STORED switch to the ON
position found on the rear of the monitor.
Figure 2. Connectors and local controls on the back panel
of a S360A.
Figure 1. GLM control network cabling
Figure 3. Connector panel detail.
MICROPHONE
PLACED IN
THE LISTENING
POSITION
292-0063
GLM TERMINA RTO
COMPUTER
RUNNING
GLM SOFTWARE
USB CABLE
GLM ADAPTER
GLM NETWORK
CABLE
MONITORS
ANALOG
IN
DIGI HRUTALT
AES/EBU
DIGITAL IN
AES/EBU
GLM
NETWORK
MAINS INPUT
50 / 60 Hz 200 W
100 - 240 V~
WARNING: ELECTRIC SHOCK HAZARD. DO N OT OPEN. DO SUBJEC ONOT T T
WATER MOISTURE. NO USERSERVICEABLEOR PA RTS INSIDE. REFER
SER QUALIFIED PERSONNEL. USEEARTHED NVICING TO MAINS CONNECTIO
ONLY.
AVERTISSEMENT RISQUE DE CHOC NEÉLECTRIQUE. PAS OUVRIR. N E PAS
EXPOSER À L'EAU L'HUMIDITÉ.OU AUCUN COMPOSANT À L 'INTÉRIEUR
REMPLAÇABLE PAR L'UTILISA ADRESSERTEUR. TOUTE RÉPARATION À UN
PERSONNEL QUALIFIÉ. CETAPPAREIL DOIT ÊTRE RACCORDÉ À LA .TERRE
LAITE ON LIITETTĂ„VĂ„ SUOJAKOSKETTIMILLA VARUSTETTUUN PISTORASIAAN.
APPARATET TILKOPLEMĂ… S JORDET STIKKONTAKT.
APPARATENSKALL A NSLUTAS TILL J ORDAT UTTAG.
This devicecomplie ithFC art15 and CanadianICES-003 radio frequencys w C P
Class B emissionrequirements. Refer tooperating manual forful nformation.l i
292- 36 0S AT-6
MADE IN FINLAND
S360A
SERIAL NUMBER
www.genelec.com
RESET YTO FACTOR
SETTINGS: PUSH
BUTT FOON R 10SEC
SENSITIVITY
IN dBu FOR
100 dB SPL (1m)
-2
+4
+2
-4 -6
+6
dBu
0
20 160
+2
-2
-4
dB
-6
0
4k 20k
BASS
TILT
800
BASS
ROLL-OFF
DESKTOP
ALL OFF
TREBLE
TILT
Frequency (Hz)
(dB)dB)
ON
OFF
BASS ROLL-OFF
BASS TILT
-2
-2
TREBLE TILT +2
DESKTOP 160 Hz -4
LED DISABLE
A
-20 dB
B
STORED
-10 dBLEVEL
DIGITAL
ISS
-4
-4
-4
TONE CONTROLS
FUNCTION SWITCHES:
- LED DISABLE
- ISS
- DIGITAL A/B
- LEVEL
- STORED
SENSITIVITY
CONTROL
POWER/RESET
SWITCH
MAINS
CONNECTOR
GLM NETWORK
CONNECTORS
DIGITAL IN,
DIGITAL THRU AND
ANALOG IN
CONNECTORS


Product specificaties

Merk: Genelec
Categorie: Monitor
Model: S360A

Heb je hulp nodig?

Als je hulp nodig hebt met Genelec S360A stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Monitor Genelec

Handleiding Monitor

Nieuwste handleidingen voor Monitor