Genelec 4010A Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Genelec 4010A (8 pagina's) in de categorie Monitor. Deze handleiding was nuttig voor 28 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8
4010A
Operating Manual
2 English
4010A
Active Loudspeaker
General
The bi-amplified Genelec 4010A is an extremely
compact two way active loudspeaker designed for
xed installations. It contains drivers, power ampli-
ers, active crossover lters and protection circuitry.
The 4010A is designed for indoor use only, in tem-
peratures between 15 to 35 degrees Celsius and
relative humidity between 20 % and 90 %.
The MDE™ (Minimum Diraction Enclosure)
loudspeaker enclosure is made of die-cast alumin-
ium and shaped to reduce edge diraction. Com-
bined with the advanced Directivity Control Wave-
guideTM (DCWTM), this design provides excellent
frequency balance in dicult acoustic environments.
Delivery contents
Each 4010A is supplied with a mains cable, a 3-pin
connector for audio signal, a keyhole type wallmount
and an operating manual.
Connections
Connect the mains cables only after you have com-
pleted connecting audio signal cabling.
Audio input is via a 10 kOhm balanced connec-
tor. The pin sequence of the connector is shown
in Figure 2.
Connect the signal cable to the 3-pole plug pro-
vided with the loudspeaker and secure the connec-
tions by tightening the screws on each pole. Push
the plug into the connector on the loudspeaker.
Never connect the 4010A to the loudspeaker
outputs of a power amplier, integrated amplier
or receiver.
When all audio connections are completed,
connect the loudspeakers to mains with the sup-
plied mains cables. They will switch on automati-
cally.
ISSTM Autostart
The 4010A is equipped with Intelligent Signal Sens-
ingTM (ISSTM) Autostart function, which automati-
cally turns the amplier to Standby mode if an input
signal has not been detected for approximately 1
hour. The power consumption in standby mode is
typically less than 0.5 watts. The playback will au-
tomatically resume once an input signal is detected
from the source.
There is a slight delay in the automatic power-
ing up. If this is undesirable, the ISSTM function can
be disabled by setting the “ISS DISABLE” switch
on the back panel to “ON” position. In this mode,
the loudspeaker is powered on and o using the
power switch on the back panel.
Sensitivity control
The input sensitivity (playback level) of the 4010A
has two alternative settings, normal and -10 dB.
The normal setting is factory default and the low-
er, -10 dB setting can be selected by turning the
“SENSITIVITY -10 dB” switch on the back panel to
“ON”.
The output levels are 100 dB @ -6dBu and 90
dB @ -6 dBu respectively. Choose the setting that
Operating Manual
English 3
Figure 1. Location of the acoustic axis
Figure 3. Control and connector layout on the rear panel of a 4010A.
Figure 2. The pin sequence of the audio input
connector.
ACOUSTIC
AXIS
107 mm
> 0,7 m
GND
+
_
TO WATER OR MOIS TURE. NO US ER SERVICEABLE PARTS
ELECTRIC SH OCK HAZAR D. DO NOT OPEN. DONOT S UBJECT
L'INTÉRIEUR R EMPLAÇABLE PAR L'UTILIS ATEUR.ADR ESSER
RIS QUE DE CHOCÉLECT RIQUE. NE S OUVRIR. N E SPA PA
EXPOSER À L'EAU OU L'H UMIDIT É. AUCUN COMPOSANT À
AVERTISSEMENT
WARNING
INS IDE. REFER S ERVICING QUALIFIED PER SONNEL.TO
TOUTE RÉPAR ATION À UN PERS ONN EL QUALIFIÉ.
292-6010W
BASS TI -4 dBLT
BASS TI -2 dBLT
ISS DISABL E
SEN SITIVITY -10 dB
TREBL E TI +2 dBLT
292-4010S
ON
292-4010T
+ GND-
4010AACTIVE
SPEAKER SYSTEM
MAINS INPUT
50 / 60 Hz 30 W
10 240 V~0 -
MADE IN FINLAND www.genelec.com
710127
ISS DISABLE,
SENSITIVITY -10 dB,
TREBLE TILT,
BASS TILT
CONTROLS
AND
AUDIO SIGNAL
INPUT CONNECTOR
MAINS
CONNECT
OR
MAINS
SWITCH


Product specificaties

Merk: Genelec
Categorie: Monitor
Model: 4010A

Heb je hulp nodig?

Als je hulp nodig hebt met Genelec 4010A stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Monitor Genelec

Handleiding Monitor

Nieuwste handleidingen voor Monitor