GE JX15BUMPBB Handleiding

GE Magnetron JX15BUMPBB

Lees hieronder de 📖 handleiding in het Nederlandse voor GE JX15BUMPBB (4 pagina's) in de categorie Magnetron. Deze handleiding was nuttig voor 47 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/4
Installation Bump-Out Kit
Instructions JX15BUMP
For 15” Deep Cabinets
49-40719-1 03-15 GE
IMPORTANT:
Use the existing mounting bracket that comes with your OTR Microwave to identify location for the Bump Out Kit.
Place the original bracket on the wall according to
installation instructions from the OTR Microwave to
determine where to place the Bump Out Kit Bracket.
Mark lowest edage of bracket
Existing Mounting Bracket
from OTR Microwave
Place the Bump Out Kit Bracet in place of existing bracket location making sure that the bottom edge lines up.
Bump-Out Kit
Bracket
2
Installation Instructions
TOOLS YOU WILL NEED
#1 and #2 Phillips screwdriver Pencil
Ruler or tape
measure and
straight edge Carpenter square
(optional)
Tin snips (for cutting
damper, if required)
Electric drill with 3ø16” , 7ø16”, 3ø8”,
1ø2” and 5ø8” drill bits
Hammer (optional)Stud finder or
Filler blocks or scrap
wood pieces, if needed
for top cabinet spacing
(used on recessed
bottom cabinet
installations only)
Gloves
Saw (saber, hole or keyhole)
Level Duct and masking tape
Scissors
(to cut template, if necessary)
Safety goggles
MOUNTING SPACE
NOTES:
The space between the cabinets must be 30” wide
and free of obstructions.
If the space between the cabinets is greater
than 30”, a Filler Panel Kit may be used to fill
in the gap between the oven and the cabinets.
Your Owner’s Manual contains the kit number for
your model.
This oven is for installation over ranges up to
36” wide.
If you are going to vent your oven to the outside,
see Hood Exhaust Section for exhaust duct
preparation.
When installing the oven beneath smooth, flat
cabinets, be careful to follow the instructions
on the top cabinet template for power cord
clearance.
Backsplash
66” or more
from the
floor to the
top of the
oven
30”
2”
30”
min.
16-1ø4”
Bottom edge
of cabinet
needs to
be 30” or
more from
the cooking
surface
NOTE: Maximum cabinet depth is 15”.
3
Installation Instructions
Find the studs, using one of the following methods:
A. Stud finder – a magnetic device which locates nails.
OR
B. Use a hammer to tap lightly across the mounting
surface to find a solid sound. This will indicate a stud
location.
After locating the stud(s), find the center by probing
the wall with a small nail to find the edges of the stud.
Then place a mark halfway between the edges. The
center of any adjacent studs should be 16" or 24" from
this mark.
Draw a line down the center of the studs.
THE OVEN MUST BE CONNECTED TO AT LEAST ONE
WALL STUD.
1
FINDING THE WALL STUDS
A.
2
PLACEMENT OF THE BUMP-OUT BRACKET
1
Wall Studs
Level line for front overhang
Center 3
ALIGNING THE WALL PLATE
Draw a vertical line on the wall at the center of the 30”
wide space.
Use mounting plate as the template for the rear wall.
Place mounting plate on the wall, making sure that the
tabs are touching the bottom of the cabinet or the level
line drawn for cabinets with front overhang. Line up the
notch and center line on the mounting plate to the center
line on the wall. (If the tabs are not in line with front
overhang, unit will be tilted.)
While holding mounting plate with one hand, draw circles
on the wall at holes A, B, C and D (see illustration above) .
Four holes must be used for mounting.
NOTE: Holes C and D are inside area E. If neither C nor D
is in a stud, find a stud somewhere in area E and draw
a fifth circle to line up with the stud. It is important to
use at least one wood screw mounted firmly in a stud to
support the weight of the oven.
Set the mounting plate aside.
Drill holes on the circles. If there is a stud, drill a 3ø16” hole
for wood screws. For holes that don’t line up with a stud,
drill a 5ø8” hole for toggle bolts.
NOTE: DO NOT MOUNT THE PLATE AT THIS TIME.
2
3
4
Draw a
Vertical Line
on Wall from
Center of Top
Cabinet
Area E
Hole Location A
Hole Location B
Hole Location D
B.
CAUTION: Wear gloves
to avoid cutting fingers
on sharp edges.
1
Hole Location C
NOTE: Appearance
and shape of the
mounting plate
may vary from your
model.

Product specificaties

Merk: GE
Categorie: Magnetron
Model: JX15BUMPBB

Heb je hulp nodig?

Als je hulp nodig hebt met GE JX15BUMPBB stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Magnetron GE

GE

GE Café CSA1201RSS Handleiding

30 November 2024
GE

GE JVM3160DFCC Handleiding

30 November 2024
GE

GE JX827BMTS Handleiding

18 November 2024
GE

GE JX9152ELDS Handleiding

18 November 2024
GE

GE JVM6175SFSS Handleiding

16 November 2024
GE

GE Profile PVM9195DFCC Handleiding

16 November 2024
GE

GE PVM9215DFWW Handleiding

16 November 2024
GE

GE UVM9125STSS Handleiding

15 November 2024
GE

GE Profile PWB7030SVSS Handleiding

27 Oktober 2024
GE

GE GCHK07N1WSS Handleiding

23 Oktober 2024

Handleiding Magnetron

Nieuwste handleidingen voor Magnetron

Whirlpool

Whirlpool MWSC 933 SW Handleiding

3 December 2024
Whirlpool

Whirlpool MWSC 9133 SX Handleiding

3 December 2024
Whirlpool

Whirlpool MWSC 933 SB Handleiding

3 December 2024
Whirlpool

Whirlpool MWSC 9133 SB Handleiding

3 December 2024
Whirlpool

Whirlpool MWF 259 B Handleiding

3 December 2024
Whirlpool

Whirlpool JT 469 BL Handleiding

3 December 2024
Whirlpool

Whirlpool MWP 253 SB Handleiding

3 December 2024
Whirlpool

Whirlpool Extra Space Crisp MWF 426 Handleiding

3 December 2024
Whirlpool

Whirlpool WMF250G Handleiding

3 December 2024
Gorenje

Gorenje MO23ORAW Handleiding

2 December 2024