Futaba R7014SB Handleiding

Futaba Radiografisch bestuurbaar speelgoed R7014SB

Lees hieronder de 📖 handleiding in het Nederlandse voor Futaba R7014SB (2 pagina's) in de categorie Radiografisch bestuurbaar speelgoed. Deze handleiding was nuttig voor 29 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

R7014SB

●Applicable systems: Futaba FASSTest-2.4GHz / FASST-Multi-ch system transmitter

◆FASSTest-2.4GHz Bidirectional Communication System / FASST-Multi-ch 2.4GHz

◆S.BUS2 / S.BUS Port and 12 Channels (+DG1,2) for Conventional System Receiver

1M23N32201

Usage precaution

• Analog servos cannot be used with the R7014SB in the FASSTest

12CH mode.

• When the FASST Multi-ch High-speed Mode is used, analog servos

cannot be used at the CH1 ∼6 outputs for convention systems. How-

ever, in other than the FASSTest 12CH mode, analog servos can be

used at CH7-12, DG1 and DG2 at any time.

• Don't connect to Extra Voltage Telemetry Port before turning on a re-

ceiver.

WARNING

Changes or modification not expressly approved by the party

responsible for compliance could void the user s authority to operate the

equipment.

The R7014SB receiver should be protected from vibration by foam

rubber, Velcro, or similar mounting methods. Protect from moisture.

Antenna installation precaution

Do not cut or bundle the receiver antenna wire.

Do not bend the coaxial cable. It causes damage.

The antennas must be mounted in such a way to assure they are strain

relieved.

Keep the antenna as far away from the motor, ESC and other noise

sources as you possibly can.

Be sure that the two antennas are placed at 90 degrees to each other.

■The R7014SB has two antennas. In order to maximize signal reception and

promote safe modeling Futaba has adopted a diversity antenna system. This allows

the receiver to obtain RF signals on both antennas and fly problem-free.

Antenna installation for carbon fuselage

You must leave 30mm at the tip of the antenna fully exposed. The

exposed antenna should be secured so that it cannot move around or

back inside of your aircraft.

Be careful of connector insertion

Don't connect an S.BUS servo / gyro to S.BUS2 connector.

Do not connect the power supply battery to other than the power

supply connector.

■There is the danger of ignition, explosion, or burning.

Link precaution

Do not perform the linking procedure while the motor's main power is

connected or the engine is operating as it may result in serious injury.

When the linking is complete, please cycle the receiver power and

ensure the receiver is properly linked to the transmitter.

Please power up your system in this order. Transmitter ﬁrst, followed

by the receiver.

If the R7014SB receiver was previously linked to another transmitter,

make sure that transmitter is not operating while linking the receiver to

the new transmitter.

56%

/LQN0RGH

VZLWFK

$QWHQQD

0RGH/(' /LQN/('

([WUD9ROWDJH

7HOHPHWU\3RUW

Thank you for purchasing a Futaba R7014SB FASSTest-2.4GHz compatible receiver.

The R7014SB receiver features bi-directional communication with a FASSTest

Futaba transmitter using the S.BUS2 port. Using the S.BUS2 port an impressive array of telemetry sensors may be utilized. It also includes both standard PWM output

ports and S.BUS output ports. The R7014SB can also be switched to the FASST-Multi-ch System.

Compliance Information Statement (for U.S.A.)

This device complies with part 15 of the FCC Rules. Operation is subject to the following three con-

ditions:

(1) This device may not cause harmful interference, and (2) This device must accept any interference

received, including interference that may cause undesired operation.

(3) RF Exposure Information (SAR)

This device meets the govern ment's requirements for exposure to radio waves. This device is de-

signed and manufactured not to exceed the emission limits for exposure to radio frequency (RF)

energy set by the Federal Communications Commission of the U.S. Government. The exposure stan-

GDUGHPSOR\VDXQLWRIPHDVX UHPHQWNQRZQDVWKH6SHFL¿F$EVRUSWLRQ5DWHRU6$57KH6$5OLPLW

set by the FCC is 1.6 W/kg. Tests for SAR are conducted using standard operating positions accepted

E\WKH)&&ZLWKWKH(87WUDQVPLWWLQJDWWKHVSHFL¿HGSRZHUOHYHOLQGLIIHUHQWFKDQQHOV

The FCC has granted an Equipment Authorization for this device with all reported SAR levels evalu-

ated as in compliance with the FCC RF exposure guidelines. SAR information on this device is on

¿OHZLWKWKH)&&DQGFDQEHIRXQGXQGHUWKH'LVSOD\*UDQWVHFWLRQRIZZZIFFJRYHRWHDIFFLGDIWHU

VHDUFKLQJRQ)&&,'$=356%*

The responsible party for the compliance of this device is:

Futaba Service Center

1$SROOR'ULYH6XLWH&KDPSDLJQ,/86$

7(/RU(PDLOVXSSRUW#IXWDEDUFFRP6XSSRUW

7(/RU(PDLOIXWDEDVHUYLFH#KREELFRFRP6HUYLFH

R7014SB Speciﬁcations

FASSTest-2.4GHz system(14ch/12ch mode)

FASST-2.4GHz system (Multi-ch mode)

S.BUS2 and S.BUS port and Linear 12ch +Digital 2ch for conventional system

receiver

• Dual antenna diversity

• Size: 1.5 x 2 x 0.6 in. (37.0x50.2x15.9mm)

• Weight: 0.7 oz. (20.8g)

• Power requirement: 3.7V to 7.4V (Voltage range: 3.5 to 8.4V)

• Battery F/S Voltage: FASSTest:It sets up with a transmitter

FASST: 3.8V *The Battery F/S voltage is set for 4-cell NiCd/NiMH battery.

Battery F/S function doesn't work properly when other type battery is used.

• Extra Voltage port: 0V-70V DC

本產品符合低功率電波輻射性電機管理辦法第十二條、第十四條等條文規定

1. 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或

變更原設計之特性及功能。

2. 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善

至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受

合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。

&+6HUYRV

'HIDXOW6%86SRUW

,WVSRVVLEOHWRFKDQJHWR'*

6%86

6%86

'*

'*



FKDQQHO

+XE

6%86HTXLSPHQW

7HOHPHWU\VHQVRU

7KHUHFHLYHUSRZHUVXSSO\FDQ

EHFRQQHFWHGWRDQ\SRUW

%DWWHU\

ۋ9

6ZLWFK

6HUYR

<KDUQHVV

:KHQDOOSRUWVDUHXVHG

90˚

Connection

(Antenna installation) Connector

The direction of the

connectors of the

bottom 3 ports is

GLIIHUHQWE\Û

LED Indication

System Mode LED Status Link LED

FASSTest Green

Solid

No signal reception Red Solid

Receiving signals Green Solid

Waiting for link Start → 2 seconds later →

Red Blink（1second）

FASST Oﬀ

No signal reception Red Solid

Receiving signals Green Solid

Receiving signals but ID is unmatched Green Blink

Waiting for link Red Blink

FASSTest

FASST −Unrecoverable error (EEPROM, etc.) Alternate blink

)87$%$&25325$7,21

<DEXWVXND&KRVHLPXUD&KRVHLJXQ&KLEDNHQ-DSDQ

3KRQH)DFVLPLOH ©FUTABA CORPORATION 2017, 2 (2)

All product and company names mentioned

herein a re the t radem arks or registered

trademarks of their respective owners.

*Fixed at neutral if a servo is connected to a port other than a usable transmitter channel.

*The telemetry and Extra Voltage ports cannot be used with the FASST system.

  

. Turn on the receiver.（Transmitter OFF）

. Press and hold the Link/Mode button for at least 5 seconds.

. When the link LED begins to blink green/red the button may be released.

. The link LED should now be blinking red in one of the patterns described by the

chart below. ( Default : FASSTest )

. Each press of the Mode/Link button advances the receiver to the next mode.

. When you reach the mode that you wish to operate in, press and hold the Mode/

Link button for more than 2 seconds.

. Once locked into the correct mode the link LED will change to a solid color.

. Please cycle the receiver(s) power off and back on again after changing the

Channel Mode.

Link LED Red blink System

 FASSTest

 FASST Multi-ch Normal mode

3 FASST Multi-ch High-speed mode

  

. Turn on the receiver.（Transmitter OFF）

. Press and hold the Link/Mode button for at least 15 seconds.

. When the link LED begins to blink red the button may be released.

. The link LED should now be blinking red in one of the patterns described by the

chart below. ( Default : S.BUS )

. Each press of the Mode/Link button advances the receiver to the next mode.

. When you reach the mode that you wish to operate in, press and hold the Mode/

Link button for more than 2 seconds.

. Once locked into the correct mode the link LED will change to a solid color.

. Please cycle the receiver(s) power off and back on again after changing the

Channel Mode.

Link LED Red blink System

 S.BUS

 DG2

FASSTest



FASSTest R7014SB is a bidirectional communication system between the receiver and FASSTest capable transmitters. Multiple optional telemetry sensors

may be connected to the on the receiver and that data is in turn displayed on the transmitter.S.BUS2

*Please see your transmitter's operation manual to conﬁgure transmitter to operate with telemetry sensors.



 Bring the transmitter and the receiver close to each other, within 20 inches (half

meter).

Turn on the transmitter. Place the transmitter into the receiver linking mode.

 Turn on the receiver.

 The receiver will wait for the linking process to begin for 2 seconds. Following

that it will return to the normal operation mode.

When the link LED of the receiver changes from blinking red to solid green,

linking is complete. (A link waiting state is ended in 1 second.)

• Refer to the transmitter's operation manual for complete details on how to place the

transmitter into the linking mode.

• If there are many FASSTest systems turned on in close proximity, your receiver might have

difﬁculty establishing a link to your transmitter. This is a rare occurrence. However, should

another FASSTest transmitter/receiver be linking at the same time, your receiver could link

to the wrong transmitter. This is very dangerous if you do not notice this situation. In order

to avoid the problem,we strongly recommend you to double check whether your receiver is

really under control by your transmitter.

• If the System Type of the transmitter is changed, the receiver will need to be re-linked to the

transmitter.



S.BUS2 S.BUS extends and supports bidirectional communication. Sensors

are connected to the S.BUS2 port.

*Only S.BUS2 capable devices may be connected to the S.BUS2 port. Standard S.BUS servos

and gyros should not be connected to the S.BUS2 port.



It connects with the battery for power, etc.

$Q RSWLRQDOH[WHUQDOYROWDJH LQSXW FDEOH&$59,1 LV XVHG7KH

voltage of the battery can be displayed with a transmitter.



When using a TMA-1 (sold separately), change the settings by the following

method.

The TMA-1 is a device for viewing the telemetry data on a smartphone or

tablet.



. Switch the receiver to FASSTest system.

. Link the transmitter and receiver, and after conﬁrming operation, turn off the

power.

. Turn on the receiver power. (Transmitter power off)

. Press the Link/Mode switch for at least 10 seconds.

. When the link LED begins to blink green the button may be released.

. T he r ecei ver e nter s the linke d wit h TM A-1 mo de, and t he LED

simultaneously begins to rapidly blink red and green.

. Press the TMA-1 link switch until the LED starts to blink and wait for the

TMA-1 to link.

. When TMA-1 linking is complete, the TMA-1 LED changes from red to green

for a moment.

. When linking is complete, turn on the receiver power and check the

operation of all the devices.



 Bring the transmitter and the receiver close to each other, within 20 inches (half

meter).

 Turn on the transmitter and receiver.

 Link operation is performed by the Link/Mode switch.

• When using TM-8 module, it's possible to set F/S position (only 3CH).

0 to 1 sec. 1 to 2 sec. More than 2 sec.

0 sec. 1 sec. 2 sec.

Press and Hold time

No function

With TM-8

(not included in this set)

To set the F/S

position(No re-link)

Re-link(ID set) and to

set the F/S position

No function

Besides TM-8 Re-link(ID set)

*Refer to the instruction manual of the transmitter or module used for a description of the

linking operation, F/S position setting methods and other details.



The MPDX-1 can be used with FASSTest by merely setting the corresponding

transmitter. (Refer to the instruction manual of the corresponding transmitter.) When

using the MPDX-1 0XOWL 3URS 'HFRGHU VROGVHSDUDWHO\ ZLWKWKH FASST system,

change the setting by the following method. Enable the MPDX-1 at channels 11 and

12. (Initial value: OFF) Channels 11 and 12 cannot be used individually for MPDX-



. Switch the receiver to the FASST system (Normal or High-speed).

. Turn on the receiver power. (Transmitter power off)

. Press the Link/Mode switch for at least 10 seconds.

. When the link LED begins to blink green the button may be released.

. The receiver enters the multi prop mode and the LED of the current mode

blinks. (Initial value: OFF)

. Each time the switch is pressed, the mode changes.

. When the receiver was switched to the desired mode, press the Link/Mode

switch for at least 2 seconds.

. When the link LED begins to rapidly blink red and green, mode switching is

complete. Release the switch.

. When switching is complete, turn on the power. When the power is turned

on, the receiver switches to the new mode.



When switched, the R7014SB can use the FASST-Multi-ch mode. When the FASST system is used, the telemetry and Extra Voltage ports cannot be used. The

FASSTV\VWHPKDVD1RUPDOPRGHDQGD+LJKVSHHGPRGH+RZHYHULQWKH+LJKVSHHGPRGHDQDORJVHUYRVFDQQRWEHXVHGDW&+-6.

Link LED Green blink Mode

1 time Multi prop mode OFF

2 time Multi prop mode ON

FASST

1 output.The MPDX-1 H[WHQGV FKDQQHO WR  FKDQQHOV +RZHYHU VLQFH WKH UHVSRQVH

speed becomes slower and there are functional restrictions, use it at simple switch

operation and other applications that require numerous channels.

Product specificaties

Merk:	Futaba
Categorie:	Radiografisch bestuurbaar speelgoed
Model:	R7014SB
Gewicht:	20.8 g
Breedte:	37 mm
Diepte:	50.2 mm
Hoogte:	15.9 mm
Certificering:	CE
Aantal:	1
Type product:	Afstandsbediening ontvanger
Niet voor kinderen 0 - 3 jaar:	Ja
Bedrijfsspanning (min):	3.5 V
Bedrijfsspanning (max):	8.4 V