Fluke T130 Handleiding

Fluke Meetapparatuur T130

Lees hieronder de 📖 handleiding in het Nederlandse voor Fluke T130 (3 pagina's) in de categorie Meetapparatuur. Deze handleiding was nuttig voor 49 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/3

T90/T110VDE/

T130VDE/T150VDE

Voltage/Continuity Tester

Instruction Sheet

Introduction

The Fluke T90/T110VDE/T130VDE/T150VDE

Electrical Testers (the Tester or Product) are

voltage and continuity testers with a rotary eld

indication (T110VDE/T130VDE/T150VDE only).

Their primary use is for test and measurement in

industrial, commercial, and household environments.

This Product complies with the most recent safety

standards for safe, reliable test and measurement.

The xed test probe cover prevents the risk of injury

when you move the instrument.

To Contact Fluke

Fluke Corporation operates worldwide. For local

contact information, go to our website: www.uke.com

To register your product, view, print, or download

the latest manual or manual supplement, go to our

website.

Fluke Corporation

P.O. Box 9090

Everett, WA 98206-9090

+1-425-446-5500

uke-info@uke.com

Safety Information

 Warning

To prevent possible electrical shock, re, or

personal injury:

●Read all safety Information before you use the

Product.

● Use the Product only as specied, or the

protection supplied by the Product can be

compromised.

● Measure a known voltage rst to make sure

that the Product operates correctly.

●Do not apply more than the rated voltage,

between the terminals or between each

terminal and earth ground.

PN 3928126

October 2011, Rev. 3, 3/21

Specications are subject to change without notice. All product

names are trademarks of their respective companies.

● Limit operation to the specied measurement

category or voltage ratings.

●Do not work alone.

●Comply with local and national safety codes.

Use personal protective equipment (approved

rubber gloves, face protection, and ame-

resistant clothes) to prevent shock and arc

blast injury where hazardous live conductors

are exposed.

●Do not use the Product around explosive gas,

vapor, or in damp or wet environments.

●Do not use and disable the Product if it is

damaged.

●Do not use the Product if it operates

incorrectly.

● Keep ngers behind the nger guards on the

probes.

●Do not use the Product if the test leads are

damaged.

●Examine the case before you use the Product.

Look for cracks or missing plastic.

●The battery door must be closed and fastened

before you operate the Product.

●Replace the batteries when the low battery

indicator shows to prevent incorrect

measurements.

●Repair the Product before use if the battery

leaks.

●For use by competent persons. Anyone

using this Product should be knowledgeable

and trained about the risks involved with

measuring voltage, especially in an industrial

setting, and the importance of taking safety

precautions and of testing the Product before

and after using it to ensure that it is in good

working condition.

Symbols

These symbols are on the Tester or in this instruction

sheet.

Symbol Explanation

Important information. Consult the

instruction sheet.

Hazardous Voltage.

¥Suitable for live working.

This product complies with the WEEE

Directive (2002/96/EC) marking

requirements. The a󰀩xed label indicates

that you must not discard this electrical/

electronic product in domestic household

waste. Product Category: With reference

to the equipment types in the WEEE

Directive Annex I, this product is classed

as category 9 "Monitoring and Control

Instrumentation" product. Do not dispose

of this product as unsorted municipal

waste. Go to Fluke’s website for recycling

information.

Symbol Explanation

Conforms to European Union Directives.

§VDE Association for Electrical, Electronic

& Information Technologies; following

rules of "Geprüfte Sicherheit."

CAT III Measurement Category III is applicable to

test and measuring circuits connected to

the distribution part of the building’s low-

voltage MAINS installation.

CAT IV Measurement Category IV is applicable

to test and measuring circuits connected

at the source of the building’s low-voltage

MAINS installation.

Accessories

The Tester is supplied with accessories.

Part Number Accessory

4083642 GS38 Probe Tip Sheath

4083656 4.2 mm ∅ Probe Extensions

4111533 H15 Belt Holster (sold separately)

4111540 C150 Zippered Soft Carrying Case

(sold separately)

Figure 1 shows the Probe Tip Protector Cap. This

multifunctional accessory is useful for tests and

storage of di󰀨erent accessories. (The Probe

Extensions are stored in the Probe Tip Protector Cap

before shipment.)

Storage area for Probe Tip Sheaths

Storage area for 4.2 mm ∅ Probe Extensions



Earth-pin safety-socket opener for UK

sockets (press opener into socket to release

safety covers, see Figure 2)

Storage area for probes when not in use

Quick Reference

Use the pushbuttons to turn the functions on or o󰀨.

See the list that follows for a quick reference to each

of these pushbuttons.

Pushbutton Description

Push to turn torch light on or o󰀨

(T110VDE, T130VDE, T150VDE).

To save battery power the

function automatically turns o󰀨

after 30 seconds.

Push to hold the value that shows

in the LCD in volt and resistance

measurements. Push again

to turn HOLD o󰀨 (T130VDE,

T150VDE).

To save battery power the

function automatically turns o󰀨

after 30 seconds.

Push this button on each of

the probes at the same time to

start the test for low impedance

switchable load.

Push and hold for 2 seconds to

turn the resistance measurement

on or o󰀨 (T150VDE only).

To save battery power, the

function automatically turns o󰀨

after 30 seconds.

Figure 3 illustrates how to store and retrieve the tip

accessories from the cap.

For storage, push Probe Tip Sheath into

place.

To retrieve, rmly push probe tip into Probe

Tip Sheath.

Pull on probe handle to remove Probe Tip

Sheath.

For storage, push 4.2 mm Probe ∅

Extensions into place.

To retrieve, rmly push probe tip into Probe

Extensions. Twist 1/4 turn.

Pull on probe handle to remove Probe

Extensions. Continue to twist until tip is tight.

1/4

Features

Model

T90 T110VDE T130VDE T150VDE

Complies with EN 61243-3:2014 • • • •

LED Indication Range: 12 V to 690 V dc and ac • • • •

V Display: Multiple LED Bargraph • • • •

Independent ELV indicator LED, indicates if >50 V ac/120 V dc is

present even in the event of no battery power or main circuit failure • • • •

LCD Indication Range: 6 V to 690 V dc and ac • •

V Display: Digital LCD 3½ digit (1 V resolution) • •

Resistance Measurement: LCD 3½ digit (0 to 1999 Ω/1Ω resolution) •

LCD Backlight • •

Display HOLD: Freeze/unfreeze display with voltage or resistance

measurement • •

CAT II 690 V / CAT III 600 V •

CAT III 690 V / CAT IV 600 V • • •

Rugged, Double-Insulated Wire • • • •

Fixed Impedance ~200 kΩ ( 3.5 mA @ 690 V)≤• • • •

Switchable Load by 2 pushbuttons (~30 mA @ 230 V) • • •

Vibration During Load (when 2 switchable load pushbuttons are

pushed)

• • •

Single-Pole Phase Test (also operates with gloves) • • • •

Rotary Field Direction (also operates with gloves) • • •

Continuity Test / Diode Test • • • •

Torch • • •

Beeper for Continuity/Phase/ACV • • • •

IP54 •

IP64 • • •

Slim Metal Probe Tips (threaded base for included tip accessories) • • • •

Probe Tip Protector Cap (secure storage for the docked probes) • • • •

4.2 mm ∅ Probe Tip Thickness Extensions (for better t in outlets) • • • •

19 mm Probe Tip distance when docked • • • •

Probe Tip Sheath (UK GS38 sheath–keeps the exposed metal to a

<4 mm limit) • • • •

Slim Probe for Ultra-Compact Form Factor •

Display

LEDs

(All Models) Description

Voltage level is backlit

zVoltage level is more than ELV

limit (>50 V ac or >120 V dc)

aVoltage is ac / phase in Single

Pole Phase test

Voltage is positive or negative at

the indicator probe

bBattery is low / Replace battery

fContinuity or diode in forward

operation

gSwitchable load is ON (two buttons

pressed and current ows)

q r 3-phase sequence indication

detected left or right turning

phases with nonindicator probe

(L1) to indicator probe (L2)

gpn76.eps

LCD

(T130VDE/

T150VDE)

Description

Display is in HOLD mode



Voltage measurement (T130VDE/

T150VDE) or resistance

measurement (T150VDE)

Resistance measurement

(T150VDE)

AC Voltage measurement

DC Voltage measurement

Battery is low / Replace battery

How to Hold the Tester

Always hold the product behind the barrier to keep the

display in view. See Figure 4.

 Warning

To prevent possible electric shock, never

touch the metal pins of the probes when

power is applied.

Self‑Test

The Tester has a built-in self test function.

Before and after use, do a self-test:

1. Touch and hold the probe tips together.

f shows and you can hear the beeper. This

makes sure that the test leads have continuity.

2. Make sure that:

• batteries are good

• b (T90, T110VDE) is NOT on

• (T130VDE VDE) does not show in B , T150

the display

3. Continue to hold the probe tips together for more

than three seconds.

4. Open the probe tips again. All LEDs (all but z

and ) must be on and all symbols in the LCD g

(T130VDE, T150VDE) show for one second. This

test makes sure that all other internal circuits and

indicators are good.

5. Measure a known voltage such as a 230 V socket

outlet. This completes the self-test and includes

the >ELV circuit.

If the Tester fails the self-test or voltage test, do not

use. See To Contact Fluke for servicing.

For an inspection of the insulation, cables, and case,

see .Safety Information

4 5

Environmental

Pollution degree 2 .......................

Protection degree IP54 (T90) .....................

IP64 (T110VDE/

T130VDE/

T150VDE)

Operating Temperature ............-15 °C to +45 °C

Storage Temperature ................-20 °C to +60 °C

Humidity ...................................85 % RH maximum

Altitude 2000 m .....................................

Vibration refer to EN61243-3 ...................................

Safety EN61243-3:2014

Agency approvals VDE-GS .....................

Transporting goods...................VBG 1, § 35

Overvoltage protection 690 V ac/dc .............

Measurement category

T90......................................CAT II 690 V

CAT III 600 V

T110VDE/T130VDE/

T150VDE CAT III 690 V ............................

CAT IV 600 V

Power supply ...............................2 x 1.5 V Micro /

LR03 / AAA

Power consumption ....................50 mA maximum /

~250 mW

Language support .......................German, English,

French, Italian

LIMITED WARRANTY & LIMITATION OF

LIABILITY

This Fluke product will be free from defects in material and

workmanship for two years from the date of purchase. This

warranty does not cover fuses, disposable batteries, or damage

from accident, neglect, misuse, alteration, contamination, or

abnormal conditions of operation or handling. Resellers are not

authorized to extend any other warranty on Fluke’s behalf. To

obtain service during the warranty period, contact your nearest

Fluke authorized service center to obtain return authorization

information, then send your defective Tester to that Service

Center with a description of the problem. Replace depleted

batteries immediately to avoid Tester damage from battery

leakage.

THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER

WARRANTIES, SUCH AS FITNESS FOR A PARTICULAR

PURPOSE, ARE EXPRESSED OR IMPLIED. FLUKE IS NOT

LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR

CONSEQUENTIAL DAMAGES OR LOSSES, ARISING FROM

ANY CAUSE OR THEORY. Since some states or countries do

not allow the exclusion or limitation of an implied warranty or of

incidental or consequential damages, this limitation of liability

may not apply to you.

Fluke Corporation Fluke Europe B.V

P.O. Box 9090 P.O. Box 1186

Everett WA 98206-9090 5602 B.D.

Eindhoven

The Netherlands

11/99

Specications

Model

T90 T110VDE T130VDE T150VDE

LEDs

Voltage range 12 V to 690 V ac/dc • • • •

Resolution ±12 V, 24 V, 50 V, 120 V, 230 V,

400 V, 690 V • • • •

Tolerance Complies with

EN 61243-3:2014 • • • •

Frequency range 0 / 40 Hz to 400 Hz • • • •

Response time 0.5 second≤• • • •

Auto power on 12V ac/dc≥• • • •

LCD

Voltage range 6 V to 690 V ac/dc • •

Resolution 1 V±• •

Tolerance (3 % rdg + 5 digits)±• •

Frequency range 0 / 40 Hz to 400 Hz • •

Response time 1 second≤• •

Auto power on 6 V ac/dc≥• •

Voltage detection Automatic • • • •

Polarity detection Full range • • • •

Range detection Automatic • • • •

Internal basic load

impedance Peak current

Maximum 3.5 mA at 690 V

200 k / Is <3.5 mA (no RCD Ω

tripping) • • • •

Operation time Duration Time = 30 seconds • • • •

Recovery time Recovery Time = 240 seconds • • • •

Switchable Load ~7 kΩ• • •

Peak current Is (load) = 150 mA • • •

RCD tripping I ~30mA @ 230V • • •

Continuity Test 0 to 400 kΩ• • • •

Accuracy nominal resistance +50 % • • • •

Test current 5 A≤ µ • • • •

Single-pole Phase Test 100 V ac to 690 V ac • • • •

Frequency range 40 Hz to 60 Hz •

50 Hz to 400 Hz • • •

Rotary Field Indication • • •

Voltage range (LEDs) 100 V to 690 V

(phase to earth) • • •

Frequency range 50 Hz to 60 Hz • • •

Resistance Measurement 0 to 1999 Ω Ω •

Resolution 1 Ω•

Tolerance ±(5 % rdg +10 digits) @ 20 °C •

Temperature coe󰀩cient ±5 digits / 10 K •

Test current 30 A≤ µ •

Size in mm (HxWxL) 245x64x28 255x78x35

Weight in kg (includes batteries) 0.18 0.27

How to Clean

Before you clean the Tester, remove it from all

measurement circuits.

 Caution

To prevent damage, do not use abrasives or

solvents on the Tester.

Clean the case with a moist cloth and weak detergent.

After you clean the Tester, do not use it for a period

of 5 hours.

When to Calibrate

Fluke recommends a calibration interval of 1 year.

Battery Replacement

If (Fluke T90/T110VDE) is on or shows in bB

the LCD (Fluke T130VDE/T150VDE) during tests or

measurements, replace the batteries.

To replace the batteries:

1. Disconnect the Tester from the measurement

circuit.

2. Open the battery cover. See Figure 8.

3. Remove the discharged batteries.

4. Replace with two new 1.5V IEC LR03 AAA

batteries.

5. Align the battery polarity as shown on the case

housing.

6. Close and attach the battery cover.

Note

Do not overtighten the screw for the battery cover.

7. Complete a self-test.

Product specificaties

Merk:	Fluke
Categorie:	Meetapparatuur
Model:	T130
Gewicht:	280 g
Breedte:	70 mm
Diepte:	38 mm
Hoogte:	260 mm
Kleur behuizing:	Black, Grey, Red, Yellow
DC voltage bereik:	- V
Type batterij:	AAA
AC voltage bereik:	- V
AC stroom bereik:	- A
Maximaal voltage:	- V