Fluke i400s Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Fluke i400s (8 pagina's) in de categorie Meetapparatuur. Deze handleiding was nuttig voor 45 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8
®
PN 2414327 February 2005
© 2005 Fluke Corporation. All rights reserved. Printed in U.S.A.
1
i400s
AC Current Clamp
Calibration Information
Introduction
XWWarning
To avoid electric shock or injury, do not perform the performance tests or
calibration procedures unless you are qualified to do so.
The information provided in this manual is for the use of qualified personnel
only.
The i400s Calibration Information provides the information necessary to verify the performance and
adjust the calibration of the Fluke i400s AC Current Clamp, hereafter known as the Current Clamp.
The following information is included in this document:
• Safety Information and Electrical Symbols
• Specifications
• Maintenance
• Performance Tests
• Calibration Adjustment
• User-Replaceable Parts
• Warranty Statement
See the i400s Instruction Sheet for complete operating instructions.
Contact Information
To contact Fluke, call:
USA: 1-888-44-FLUKE (1-888-443-5853)
Canada: 1-800-36-FLUKE (1-800-363-5853)
Europe: +31 402-675-200
Japan: +81-3-3434-0181
Singapore: +65-738-5655
Anywhere in the world: +1-425-446-5500
USA Service: 1-888-99-FLUKE (1-888-993-5853)
For additional information about Fluke, its products, and services, visit Fluke’s web site at:
www.fluke.com
To register this product, go to register.fluke.com
i400s
Calibration Information
2
Safety Information
XW Read First: Safety Information
To ensure safe operation and service of the Current Clamp, follow these
instructions:
• Read the operating instructions before use and follow all safety
instructions.
• Use the Current Clamp only as specified in the operating instructions,
otherwise the clamp’s safety features may not protect you.
• Adhere to local and national safety codes. Individual protective equipment
must be used to prevent shock and arc blast injury where hazardous live
conductors are exposed.
• Do not hold the Current Clamp anywhere beyond the tactile barrier, see
Figure 1.
• Before each use, inspect the Current Clamp. Look for cracks or missing
portions of the clamp housing or output cable insulation. Also look for
loose or weakened components. Pay particular attention to the insulation
surrounding the jaws.
• Never use the Current Clamp on a circuit with voltages higher than 1000 V
CAT III or 600 V CAT IV.
• CAT III equipment is designed to protect against transients in
equipment in fixed-equipment installations, such as distribution
panels, feeders and short branch circuits, and lighting systems in
large buildings.
• CAT IV equipment is designed to protect against transients from the
primary supply level, such as an electricity meter or an overhead or
underground utility service.
• Use extreme caution when working around bare conductors or bus bars.
Contact with the conductor could result in electric shock.
• Use caution when working with voltages above 60 V dc or 30 V ac. Such
voltages pose a shock hazard.
Electrical Symbols
The symbols in Table 1 appear in this document and on the Current Clamp.
Table 1. Electrical Symbols
Symbol Explanation
, Application around and removal from hazardous live conductors is permitted.
T Product is protected by double insulation.
W Risk of Danger. Important information. See Instruction Sheet.
X Hazardous voltage.
) Conforms to relevant Canadian Standards Association directives.
P Conforms to relevant European Union directives.
AC Current Clamp
Safety Specifications
3
Tactile Barrier
bbc03f.eps
Figure 1. Tactile Barrier
Safety Specifications
Category Rating: CAT III 1000 V and CAT IV 600 V per EN61010-1, Pollution Degree 2
EMC: EN 61326-1, FCC for emission and immunity
): Tested to US and Canadian standards for compliance to UL61010-1 and CAN/CSA C22.2 No.
101.1:2004
P: IEC 61010-1 2nd Edition IEC 61010-02-032
Electrical Specifications
Reference Conditions: 23 ± ° 5 C, 20 to 75 % RH; conductor centered in jaw opening; no DC component;
no adjacent conductor.
40 A Range 400 A Range
Measurement Range 0.5 A to 40 A 5 A to 400 A
Output 10 mV/A 1 mV/A
Accuracy
45 Hz to 400 Hz
2 % + 0.015 A
2 % + 0.04 A
Phase Shift:
(45 Hz to 400 Hz)
0.5 A to 1 A
1 A to 5 A
5 A to 10 A
10 A to 20 A
20 A to 40 A
40 A to 400 A
Unspecified
4Ëš
3Ëš
3Ëš
2Ëš
NA
NA
NA
Unspecified
2Ëš
2Ëš
1.5Ëš
Crest Factor • 3 • 3 to 300 A
• 2.5 to 400 A
Typical Bandwidth: 5 Hz to 10 kHz
Working Voltage: 1000 V ac rms, in compliance with EN61010
Common Mode Voltage: 1000 V ac rms from earth ground, in compliance with EN61010


Product specificaties

Merk: Fluke
Categorie: Meetapparatuur
Model: i400s

Heb je hulp nodig?

Als je hulp nodig hebt met Fluke i400s stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Meetapparatuur Fluke

Handleiding Meetapparatuur

Nieuwste handleidingen voor Meetapparatuur