Fibaro FIB_FGWPE-101 Handleiding

Fibaro Niet gecategoriseerd FIB_FGWPE-101

Lees hieronder de 📖 handleiding in het Nederlandse voor Fibaro FIB_FGWPE-101 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 175 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

ENG

Fibaro is a bi-directional wireless system. This means that the

signal is not only sent to the receivers, but also the receivers send

the confirmation of its reception. This operation confirms their

status to check whether they are active. Safety of the Fibaro

System transmission is comparable to the safety of transmission in

data bus wired systems.

Fibaro operates in the free band for data transmission. The

frequency depends on radio regulations in individual country. Each

Fibaro network has its own unique network identification number

(home ID), which is why it is possible to co-operate two or more

independent systems in a single building without any interference.

Although Z-Wave is quite new technology, it has already become

recognizable and officially binding standard, similarly to Wi-Fi.

Many manufacturers in various industries offer solutions based on

Z-Wave technology, guaranteeing their compatibility. This means

that the system is open and it may be extended in the future. Find

more information at www.fibaro.com.

Fibaro generates a dynamic network structure. After Fibaro System

is switched on, the location of its individual components is

automatically updated in real-time through status confirmation

signals received from devices operating in a "mesh" network.

The Fibaro Wall Plug is hereinafter referred to as Plug. It is

designed to turn on / off electrical devices (see specifications) using

radio waves, controllers and push button located in it's casing. Plug

automatically recognizes connected load and is protected from

overcurrent or short circuit. Features unique, real-time energy

consumption measuring through color changing, crystal LED ring.

II. Installation

1) Insert device into a socket,

2) Add device into the Z-Wave network if necessary,

3) Connect load to the Plug, making sure it does not exceed

2 500W,

4) Set the connected device switch to ON,

5) To turn on connected device manually turn on the Plug using B

button. (Alternative to remote control via Z-Wave controller)

Once the Plug is turned on, LED ring will glow.

6) Current power load is visualized with LED ring color,

7) Press B button to turn off the Plug manually,

8) Once the Plug is turned off, LED ring illumination is turned off as

well.

Fig. 1 Wall Plug icon in Home Center 2 interface

Through an association Fibaro Wall Plug may control another

Z-Wave network device, e.g. another Fibaro Wall Plug, Dimmer,

Relay Switch or Roller Shutter.

The Fibaro Wall Plug provides three association groups:

I association group is assigned to Plugs status - On / Off. Allows

for sending control command to associated devices whenever the

Plug is turned On or Off.

II association group allows for sending control commands to

associated devices depending on the current load. This association

group is configured through the advanced parameters no. 50, 51

and 52.

III association group reports relay's status to just one device,

Z-Wave network's main controller by default. It's not recommended

to modify settings of this association group.

The Fibaro Wall Plug allows for associating 5 normal devices per

single association group, out of which 1 field is always reserved for

main controller.

VII. Association

NOTE

To disable auto-inclusion press the B button once

after inserting the Plug into a socket.

NOTE

Association allows for direct communication

between Z-Wave network devices. Main controller

does not take part in such communication.

Fibaro Wall Plug offers a wide variety of advanced configuration

settings. Below parameters can be accessed from main controllers

configuration interface.

To configure Wall Plug using Home Center 2 controller go to device

options by clicking the following icon:

Select the advanced settings tab.

X. Advanced configuration

Operating Manual

Fibaro Wall Plug

FGWPE/F-101 v.2.1 - v.2.3

Fibaro Wall Plug is a universal, Z-Wave compatible, relay switch in

the form of a socket adapter. The Plug may be used to operate any

device up to 2,500W power output. The Plug features power

consumption measuring and uses a crystal LED ring to visualize the

current load by colour changing illumination.

Fibaro Wall Plug may be operated using the service button located

on its casing, or via any Z-Wave compatible controller.

Specifications

Power supply:

Rated load current:

Power consumption:

Power output:

(For resistive load)

In accordance with EU

standards:

Circuit’s temperature limit:

Operational temperature:

Circuit's thermal protection:

To be used with E or F type

(Schuko) sockets:

Radio signal power:

Radio protocol:

Radio frequency:

Range:

Dimensions: (D x H):

110-230 V AC +/-10%, 50/60 Hz

11A, 110-230V, 50/60 Hz -

continuous load

13A, 110-230V, 50/60 Hz -

momentary load

up to 0,8W

2,5kW at continuous load

3,0kW at momentary load

EN 55015 (noise)

EN 60669-2-1 (operational

safety)

105 °C

0 - 40 °C

115o

C - Ta (Ta = ambient

temperature).

- CEE 7/16 - max load 2,5 A

- CEE 7/17 - max load 16A

- Dual type plugs E/F

1mW

Z-Wave

868,4 MHz

up to 50m outdoors

up to 30m indoors (depending

on building materials)

43 x 65mm

Technical Information

- Controlled by Fibaro devices or any other Z-Wave controller

- Microprocessor control

- Executive element - relay

- Active and historic (average) power consumption measuring

NOTE

In case of loads other than resistive please observe

cosɸ and use load lower than rated if necessary.

It's recommended not to exceed 8A / 1,5kW

III. Z-Wave network inclusion

Fibaro Wall Plug may be controlled manually, by the B button

located on its casing, or via any Z-Wave controller. To include the

Plug into the Z-Wave network please complete following tasks:

1) Insert the Plug into a socket,

2) Auto-inclusion will be activated, i.e. Plug automatically starts

looking for Z-Wave network controller. Auto-inclusion activation is

signaled by a single, red, LED ring blink.

3) Set the Z-Wave network main controller into learning mode (see

Z-Wave network controller operating manual)

4) Fibaro Wall Plug should be recognized and automatically

included into the Z-Wave network.

After the inclusion process is completed, Plug's auto-inclusion

function is deactivated, i.e. Plug will not try to include itself into the

Z-Wave network.

NOTE

Resetting the Plug does not mean is has been

removed from Z-Wave network controller's

memory. Remove the Plug from Z-Wave network

controller's memory before carrying out the

resetting procedure.

VI. Operating the Plug through Z-Wave network

After successful inclusion Plug will be represented in the Home

Center 2 by the following, single icon:

Clicking ON/OFF will turn a connected device On or Off.

NOTE

Group I association commands are sent only in

case of manual operation through the B button.

Group II association commands are sent

automatically, depending on parameters no. 50, 51

and 52 settings.

NOTE

Please contact your local electricity supplier for the

current rates.

2) Fibaro Wall Plug stores consumed electricity data in its memory,

which means disconnecting the Plug from a socket does not erase

the data.

To reset electricity consumption memory:

a) Insert the Plug in a socket,

b) Press and hold the B button for 5-10 seconds until LED ring

glows green,

c) Release the B button,

d) Press the B button briefly.

Resetting electricity consumption memory will be signaled by

double, green, LED ring blink. Plug's relay won't change its status.

NOTE

Turning off the LED ring turns off alarm signaling

as well.

3) Frequently asked questions about power and energy

consumption measuring.

Why doesn't a device consume precisely 100W, when its data

plate says this is the power exactly?

Power data specified by producers are often based on rough

estimates or measured in perfect conditions. Real world power

depends on mains voltage, device condition or ambient conditions

the device is used in. It may happen that two identical devices will

consume different amounts of energy.

Why power of the same device differs depending on the socket

it is connected to, in the same house?

Such things happen because of mains voltage fluctuations. Causes

also include wire lengths and voltage drops between the sockets.

Why the power of the same device differs in times of day?

The reason is the mains voltage fluctuations.

Why do we measure power, not any other parameter instead?

Power measuring is important because based on this parameter

electricity suppliers charge households for energy use.

Why certain devices power fluctuates instead of being

constant?

Some devices may have such a characteristic, e.g. computers.

In case of devices frequently, significantly changing power

consumption, e.g. plasma TVs, it is recommended to modify

configuration parameters to optimize the Z-Wave network use.

Modify parameters no. 40, 42 and 43 settings in order to reduce the

frequency of reporting the power use.

To reduce the number of power reports, value of the parameters 42

and/or 43 must be increased, based on user's experience. (e.g.

parameter 42 set to 30 and parameter 43 set to 60).

NOTE

Some Z-Wave network controllers allow for

resetting electricity consumption from controllers

menu.

The Fibaro Wall Plug features built-in network range status, in

relation to the Z-Wave network main controller.

To test the range:

1) Insert Plug into a mains socket,

2) Press and hold the B button for 10-15 seconds until the LED ring

glows violet,

3) Release the B button,

4) Press the B button briefly.

5) LED ring signals Z-Wave network range - see below for signaling

modes description.

6) To exit range testing mode press the B button briefly. Plugs relay

will not change its status.

Z-Wave network range signaling modes:

LED ring pulsing green - Wall Plug tries to establish direct

connection with the main controller. If direct connection cannot be

established, Plug will try routing connection with the main controller

which will be signaled by LED ring pulsing yellow.

LED ring glowing green - Wall Plug managed to establish a direct

connection with the main controller.

LED ring pulsing yellow - Wall Plug is trying to establish routed

connection with the main cotroller, via other Z-Wave devices acting

as signal repeaters.

LED ring glowing yellow - Wall Plug managed to establish routed

connection with the main controller. After 2 seconds the Plug will try

again to establish a direct connection with the main controller, which

will be signaled by LED ring pulsing green.

LED ring pulsing violet - Wall Plug is located outside the Z-Wave

network's range or the network is busy. Ultimately, failure to connect

with the main controller will be signalled by LED ring pulsing red.

After 2 seconds the Plug will again try to establish a direct

connection with the main controller which will be signalled by LED

ring blinking green.

To include the Plug manually, without the use of auto-inclusion:

1) Set the Z-Wave controller into the learn-mode (see Z-Wave

controller operating manual),

2) Triple click the B button, located on the Plug's casing

IV. Removing from Z-Wave network

To remove Fibaro Wall Plug from the Z-Wave network:

1) Insert the Plug into a socket,

2) Set the Z-Wave network controller into the learn-mode (see

Z-Wave controller operating manual)

3) Triple click the B button, located on the Plug's casing.

ALARMS:

Z-Wave network alarm will be signalled by LED ring according to the

parameter 63 settings. Blinking in Red/Blue/White is a default

setting.

Connected device state will be changed according to the parameter

35 settings. By default, connected device state will remain

unchanged.

Wall Plug will be signaling an alarm through the time period specified

in the parameter 39 (10 minutes by default), unless the alarm is

cancelled earlier. In addition Wall Plug may exit the alarm mode after

the B-button has been pressed and held for 2 - 5 seconds.

I. General information about Fibaro System

Fibaro is a wireless system, based on Z-Wave technology. Fibaro

provides many advantages when compared to similar systems. In

general, radio systems create a direct connection between the

receiver and transmitter. But the radio signal is weakened by

various obstacles located on its path (apartment walls, furniture,

etc.) and in extreme cases it fails to transfer required data. The

advantage of Fibaro System is that its devices, apart from being

transmitters and receivers, are also signal duplicators. When a

direct connection path between the transmitter and the receiver

cannot be established, the connection may be achieved through

other intermediate devices.

V. Resetting Fibaro Wall Plug

Reset procedure clears the Plug's memory, including Z-Wave

network controller information and energy consumption data.

To reset Fibaro Wall Plug:

1) Insert the Plug into a socket,

2) Press and hold the B button for 15 - 20 seconds until LED ring

glows yellow,

3) Release the B button,

4) Press the B button, briefly.

Once the reset procedure is completed, LED ring will glow red and

turn off. Plug's relay will turn off as well.

To add an association (using Home Center 2 Interface) go to device

settings and click the following icon:

Select the "device options" tab. Then specify to which group and

what devices are to be associated. Sending relevant information to

devices added to association groups may take even a few minutes.

1) Fibaro Wall Plug allows for the current load and power

consumption monitoring. Data is sent to the main controller, e.g.

Home Center 2. Measuring is carried out by an independent

microprocessor dedicated exclusively for this purpose, assuring

maximum accuracy and precision.

Electric power - power consumed by an electric device in an

instant, in Watts (W).

Electric energy - energy consumed by a device through a time

period. Most commonly measured in kilowatt-hours (kWh). One

kilowatt-hour is equal to one kilowatt of power consumed over a

period of one hour, 1kWh = 1000 Wh.

VIII. Current load and energy consumption

IX. Led rings settings and readings

The Fibaro Wall Plug has built-in, colour changing LED ring,

signaling connected devices power and operating status. Colours

shown are those of a RGB scheme. In addition, the LED ring signals

Plugs range in relation to the Z-Wave networks main controller and

overheating protection activation (parameter no.70).

LED rings signaling modes:

1) Wall Plugs On / Off signaled with a color defined by relevant

parameter settings (see parameters no. 60, 61, 62)

2) Alarm status signaled according to parameters 63 settings,

3) Energy meter reset signaled by double, green blink,

4) Once inserted to mains socket, LED ring signals Z-Wave network

inclusion status. Single green blink means it's included. Single red

blink means Plug has not been included in the Z-Wave network.

5) Blinking yellow means memory write during software update

process,

6) Alternating blinking, yellow / red, signals overheating warning

(overload).

LED ring illumination may be turned off completely. To do so:

1) Insert the Plug in a socket,

2) Press and hold the B button for 2-5 seconds, till LED ring starts

pulsing white,

3) Release the B button,

4) Press the B button briefly.

Plugs relay will not change its status. After the LED ring has been

turned off, it can be turned on by completing again the above

procedure.

GENERAL:

1. Always on function

Once activated, Wall Plug will keep a connected device constantly

ON, will stop reacting to alarm frames and B-button push.

"Always on" function turns the Plug into a power and energy meter.

Also, connected device will not be turned off upon receiving an alarm

frame from another Z-Wave device (parameter 35 will be ignored).

In "Always on" mode, connected device may be turned off only after

user defined power has been exceeded (parameter 70). In such a

case, connected device can be turned on again by pushing the

B-button or sending a control frame. By default, overload protection

is inactive. Default setting: 1

Available settings:

0 - function activated

1 - function inactive

Parameter: 1 [byte]

16 - Remember device status after power failure

Define how will the Plug react after the power supply is back on.

Default setting: 1

Available settings:

0 - Wall Plug does not memorize its state after a power failure.

Connected device will be off after the power supply is

reconnected.

1 - Wall Plug memorizes its state after a power failure.

Parameter: 1 [byte]

34. Reaction to alarms.

Define Z-Wave network alarms to which the Wall Plug will respond.

Default setting: 63

Available settings: 0 - 63.

1 - general alarm,

2 - smoke alarm,

4 - CO alarm,

8 - CO2 alarm,

16 - high temperature alarm,

32 - flood alarm,

63 - device responds to all types of alarm frames.

Set value may be a sum of available values, e.g. set value = 5 means

the Plug will respond to general alarm (1) and CO alarm (4).

Parameter: 1 [byte]

35. Wall Plug's response to alarm frames

Parameter defines how the Wall Plug will respond to alarms (device's

status change) Default setting: 0

Available settings:

0 - no reaction,

1 - turn on connected device. LED ring signals an alarm through

defined time period (parameter 39) or untill the alarm is

cancelled.

2 - turn off connected device. LED ring signals an alarm through

defined time period (parameter 39) or untill the alarm is

cancelled.

3 - cyclically change device state, each 1second. In alarm mode

Wall Plug does not report status change, power changes,

ignores alarm frames. After the defined time period has passed

(parameter 39) or after the alarm cancellation, connected

device is set to the previous state.

Parameter: 1[byte]

REPORTS

39. Alarm duration

Wall Plug's alarm mode duration. If a device sending an alarm frame

through the Z-Wave network sets alarm duration as well, this

parameter's settings are ignored.

Default setting: 600 (seconds).

Available settings: 1 - 65536 (seconds)

Parameter: 2[byte]

Reports on power load, sent to the main controller. Default settings

of below parameters are chosen in such a way that instantaneous

power load is shown without blocking the Z-Wave network in the

process. Default settings are good for most of the devices. In

specific cases it may be necessary to modify default settings in order

to optimize Z-Wave network's use. In extreme cases it is recommen-

ded to turn off reporting completely and configure power polling or

periodic reports in Home Center 2.

Fibaro Wall Plug reports the power load with specified frequency.

Below configuration parameters allow to specify how and how

frequently power load will be reported.

40. Immediate power report.

Parameter defines by how much power load must change, in

percents, to be reported to the main controller, with the highest

priority in the Z-Wave network. By default, Fibaro Wall Plug

immediately sends power report if the power load changes by 80%.

Default setting: 80 (%)

Available settings: 1 - 100 (%).

Value of 100 (%) means the reports are turned off.

Parameter: 1[byte].

NOTE

In extreme cases, reports may be sent every

second if rapid and significant power load changes

occur. Frequent reporting may overload the

Z-Wave network so these parameter's settings

should reflect significant changes in power load

only.

NOTE

If "always on" function is active (parameter 1), this

parameter's settings are ignored.

1. The Guarantee is provided by FIBAR GROUP Sp. z o.o.

(hereinafter "Manufacturer"), based in Poznan, ul. Lotnicza 1; 60-421

Poznan, entered in the register of the National Court Register kept

by the District Court in Poznań, VIII Economic Department of the

National Court Register, no. 370151, NIP 7811858097, REGON:

301595664.

2. The Manufacturer is responsible for equipment malfunction

resulting from physical defects (manufacturing or material) of the

Device for 12 months from the date of its purchasing.

3. During the Guarantee period, the Manufacturer shall remove any

defects, free of charge, by repairing or replacing (at the sole

discretion of the Manufacturer) any defective components of the

Device with new or regenerated components, that are free of

defects. When the repair impossible, the Manufacturer reserves the

right to replace the device with a new or regenerated one, which shall

be free of any defects and its condition shall not be worse than the

original device owned by the Customer.

4. In special cases, when the device cannot be replaced with the

device of the same type (e.g. the device is no longer available in the

commercial offer), the Manufacturer may replace it with a different

device having technical parameters similar to the faulty one. Such

activity shall be considered as fulfilling the obligations of the

Manufacturer. The Manufacturer shall not refund money paid for the

device.

5. The holder of a valid guarantee shall submit a guarantee claim

through the guarantee service. Remember: before you submit a

guarantee claim, contact our technical support using telephone or

e-mail. More than 50% of operational problems is resolved remotely,

saving time and money spent to initiating guarantee procedure. If

remote support is insufficient, the Customer shall fill the guarantee

claim form (using our website - www.fibargroup.com) in order to

obtain claim authorization.

When the guarantee claim form is submitted correctly, the Customer

shall receive the claim confirmation with an unique number (Return

Merchandise Authorization -RMA).

6. The claim may be also submitted by telephone. In this case, the

call is recorded and the Customer shall be informed about it by a

consultant before submitting the claim. Immediately after submitting

the claim, the consultant shall provide the Customer with the claim

number (RMA-number).

7. When the guarantee claim form is submitted correctly, a

representative of the Authorised Guarantee Service (hereinafter as

"AGS") shall contact the Customer.

XI. Guarantee

NOTE

This functionality is not an overload safety

protection nor a short circuit protection. Circuit

needs additional short circuit and overload

protection.

ASSOCIATION GROUP 2

COLOUR SETTINGS

SAFETY

This Device may be used with all devices

certified with Z-Wave certificate and should be

compatible with such devices produced by

other manufacturers.

Any device compatible with Z-Wave may be added

to Fibaro system.

FIBARGROUP

FIBARO

In case of any technical questions contact customer service centre

in your country.

www.fibargroup.com

8. Defects revealed within the guarantee period shall be removed

not later than 30 days from the date of delivering the Device to AGS.

The guarantee period shall be extended by the time in which the

Device was kept by AGS.

9. The faulty device shall be provided by the Customer with complete

standard equipment and documents proving its purchase.

10. Parts replaced under the guarantee are the property of the

Manufacturer. The guarantee for all parts replaced in the guarantee

process shall be equal to the guarantee period of the original device.

The guarantee period of the replaced part shall not be extended.

11. Costs of delivering the faulty device shall be borne by the

Customer. For unjustified service calls, the Service may charge the

Customer with travel expenses and handling costs related to the

case.

12. AGS shall not accept a complaint claim only when:

• the Device was misused or the manual was not observed,

• the Device was provided by the Customer incomplete, without

accessories or nameplate,

• it was determined that the fault was caused by other reasons than

a material or manufacturing defect of the Device

• the guarantee document is not valid or there is no proof of

purchase,

13. The Manufacturer shall not be liable for damages to property

caused by defective device. The Manufacturer shall not be liable for

indirect, incidental, special, consequential or punitive damages, or

for any damages, including, inter alia, loss of profits, savings, data,

loss of benefits, claims by third parties and any property damage or

personal injuries arising from or related to the use of the Device.

14. The guarantee shall not cover:

• mechanical damages (cracks, fractures, cuts, abrasions, physical

deformations caused by impact, falling or dropping the device or

other object, improper use or not observing the operating manual);

• damages resulting from external causes, e.g.: flood, storm, fire,

lightning, natural disasters, earthquakes, war, civil disturbance, force

majeure, unforeseen accidents, theft, water damage, liquid leakage,

battery spill, weather conditions, sunlight, sand, moisture, high or low

temperature, air pollution;

• damages caused by malfunctioning software, attack of a computer

virus, or by failure to update the software as recommended by the

Manufacturer;

• damages resulting from: surges in the power and/or telecommuni-

cation network, improper connection to the grid in a manner

inconsistent with the operating manual, or from connecting other

devices not recommended by the Manufacturer.

• damages caused by operating or storing the device in extremely

adverse conditions, i.e. high humidity, dust, too low (freezing) or too

high ambient temperature. Detailed permissible conditions for

operating the Device are defined in the operating manual;

• damages caused by using accessories not recommended by the

Manufacturer

• damages caused by faulty electrical installation of the Customer,

including the use of incorrect fuses;

• damages caused by Customer's failure to provide maintenance and

servicing activities defined in the operating manual;

• damages resulting from the use of spurious spare parts or

accessories improper for given model, repairing and introducing

alterations by unauthorized persons;

• defects caused by operating faulty Device or accessories.

15. The scope of the guarantee repairs shall not include periodic

maintenance and inspections, in particular cleaning, adjustments,

operational checks, correction of errors or parameter programming

and other activities that should be performed by the user (Buyer).

The guarantee shall not cover natural wear and tear of the Device

and its components listed in the operating manual and in technical

documentation as such elements have a defined operational life.

16. If a defect is not covered by the guarantee, the Manufacturer

reserves the right to remove such defect at its sole discretion,

repairing the damaged or destroyed parts or providing components

necessary for repair or replacement.

17. This guarantee shall not exclude, limit or suspend the Customer

rights when the provided product is inconsistent with the purchase

agreement.

42. Standard power load reporting.

Parameter defines by how much power load must change, in

percents, to be reported to the main controller. By default, Fibaro

Wall Plug sends power report if the power load changes by 15%.

By default such changes in power load may be reported up to 5 times

per 30 seconds. Wall Plug sends 5 reports during time period

specified in paramater 43.

Default setting: 15 (%)

Available settings: 1 - 100 (%)

Value of 100 (%) means the reports are turned off.

Parameter: 1[byte]

43. Power reporting frequency.

This parameter defines how frequently standard power reports

(parameter 42) will be sent. By default Wall Plug sends up to 5

reports each 30 seconds, provided the power load changes by 15%.

Default seting: 30 (s)

Available settings: 1 - 254 (s)

Value of 255 - Reports will be sent only as a result of parameter 47

settings or in case of polling.

Parameter: 1[byte]

45. Reporting changes in energy consumed by controlled

devices

New, reported energy value is calculated based on last reported

value. Default setting: 10 (0,1 kWh).

Available settings: 1 - 254 (0,01kWh - 2,54kWh).

Value of 255 - changes in consumed energy will not be reported.

Reports will be sent only in case of polling.

Parameter: 1[byte]

61. LED ring illumination colour when controlled device is on.

Default value: 1

Available settings:

0 - LED ring illumination colour changes in predefined steps,

depending on power consumption changes,

1 - LED ring illumination colour changes continuously, using full

spectrum of available colorus, depending on power consumption

changes.

2 - White illumination,

3 - Red illumination,

4 - Green illumination,

5 - Blue illumination,

6 - Yellow illumination,

7 - Cyan (Greenish blue) illumination,

8 - Magenta (Purplish red) illumination,

9 - illumination turned off completely.

Parameter: 1[byte]

62. LED ring illumination color when controlled device is off.

Default setting: 8

Available settings:

0 - LED ring is illuminated with a color corresponding to the last

measured power, before the controlled device was turned off,

1 - White illumination,

2 - Red illumination,

3 - Green illumination,

4 - Blue illumination,

5 - Yellow illumination,

6 - Cyan (Greenish blue) illumination,

7 - Magenta (Purplish red) illumination,

8 - illumination turned off completely.

Parameter: 1[byte]

70 . Oveload safety switch

This function allows for turning off the controlled device in case of

exceeding the defined power. Controlled device will be turned off

even if "always on" function is active (parameter 1).

Controlled device can be turned back on via B-button or sending a

control frame. By default this function is inactive.

Default setting: 65 535 (6 553,5W)

Available settings: 10 - 65 535 (1W - 6 553,5W).

Value higher than 32 000 (3 200W) turns the overload safety switch

off, i.e. this functionality is turned off by default.

Parameter: 2[byte]

49. Metering energy consumed by the Wall Plug itself.

This parameter determines whether energy metering should include

the amount of energy consumed by the Wall Plug itself.

Results are being added to energy consumed by controlled device.

Default setting: 0

Available settings:

0 - function inactive,

1 - function activated.

Parameter: 1[byte]

Status of devices added to 2nd Association Group may depend on

power consumed by the connected device. For example, turning on

the TV controlled by the Plug will turn off the lights in the room.

User defines two thresholds: UP and DOWN, and then defines the

reaction to them being exceeded (parameter 52).

50. DOWN value

Lower power threshold, used in parameter 52.

Default setting: 300 (30 W)

Available settings: 0 - 25 000 (0,0W - 2 500W)

DOWN value cannot be higher than a value specified in parameter

51.

Parameter: 2[byte]

51. UP value

Upper power threshold, used in parameter 52.

Default setting: 500 (50 W)

Available settings: 1 - 25 000 (0,1W - 2 500W)

UP value cannot be lower than a value specified in parameter 50.

Parameter: 2[byte]

60. Power load, which when exceeded, makes the LED ring

flash violet.

Function is active only when parameter 61 is set to 0 or 1.

Default setting: 25 000 (2 500W)

Available settings: 1 000 - 32 000 (100W - 3200W).

Parameter: 2[byte]

52. Action in case of exceeding defined power values

(parameters 50 and 51)

Parameter deifines the way 2nd association group devices are

controlled, depending on the current power load.

Default setting: 6

Available settings:

0 - function inactive,

1 - turn the associated devices on, once the power drops below

DOWN value (parameter 50),

2 - turn the associated devices off, once the power drops below

DOWN value (parameter 50),

3 - turn the associated devices on, once the power rises above UP

value (parameter 51),

4 - turn the associated devices off, once the power rises above UP

value (parameter 51),

5 - 1 and 4 combined. Turn the associated devices on, once the

power drops below DOWN value (parameter 50). Turn the

associated devices off, once the power rises above UP value

(parameter 51).

6 - 2 and 3 combined. Turn the associated devices off, once the

power drops below DOWN value (parameter 50). Turn the

associated devices on, once the power rises above UP value

(parameter 51).

Parameter: 1[byte]

47. Time period between reports on power load and energy

consumption.

Parameter defines time period between reports sent when changes

in power load have not been recorded. By default, if power load

changes have not been recorded, reports are sent every hour.

Default setting: 3 600 (s),

Available settings: 1 - 65534 (s)

Value of 65535 - no periodic reports. Reports will be sent only in

case of power load / energy consumption changes (parameters 40,

42, 43,45) or in case of polling.

Parameter: 2[byte]

63. LED ring illumination colour at the Z-Wave network alarm

detection. Default setting: 1

Available settings:

0 - No change in colour. LED ring illumination colour determined by

parameters 61 or 62 settings,

1 - LED ring flashes red / blue / white (default),

2 - White illumination,

3 - Red illumination,

4 - Green illumination,

5 - Blue illumination,

6 - Yellow illumination,

7 - Cyan (Greenish blue) illumination,

8 - Magenta (Purplish red) illumination,

9 - illumination turned off completely.

Parameter: 1[byte]

Product specificaties

Merk:	Fibaro
Categorie:	Niet gecategoriseerd
Model:	FIB_FGWPE-101
Kleur van het product:	Wit
Diepte:	43 mm
Hoogte:	65 mm
LED-indicatoren:	Ja
Huidige waardering:	11 A
Maximaal vermogen:	2500 W
AC-ingangsspanning:	110-230 V
AC-ingangsfrequentie:	50 - 60 Hz
Aantal stopcontacten:	1
Geslacht connector:	Mannelijk/Vrouwelijk
Type stekkeraansluiting:	Type E (FR)
Type stopcontactaansluiting:	Type E (FR)