EXSYS EX-3516 Handleiding

EXSYS Controller EX-3516

Lees hieronder de 📖 handleiding in het Nederlandse voor EXSYS EX-3516 (10 pagina's) in de categorie Controller. Deze handleiding was nuttig voor 29 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/10

Thank you for purchasing this 4-Port SATA3 RAID/HyperDuo PCIe Card.

It is designed to support up to 4 SATA3 ports in RAID 0 and RAID 1,

RAID 0+1 modes and HyperDuo modes for SSD (Solid State Drive) and

hard drive combination. It supports SATA3 SSD and hard drives with up

to 6.0Gbps data rate. It is an ideal solution to add new SATA3 SSD and

hard drives for your system.

Features:

 Supports 1-lane 5.0Gb/s PCI Express Gen.2 Data Transfer Rate

 Built-in 4 Internal SATA3 Ports

 Supports RAID 0,1, 0+1 and HyperDuo (Safe or Capacity) Modes

 Supports Windows based RAID GUI (Marvell Storage Utility, MSU)

 Supports SATA3 transfer rate up to 6.0Gb/s (600Mbytes/sec)

 Supports RAID 1 Rebuild by BIOS Setup Utility

 Supports Windows 2003, 2008, XP, Vista and Win 7

EX-3516

4-Port SATA3 RAID/HyperDuo

PCIe(x2) Card

1. Introduction

2. Board Layout

JP1 BIOS

Enable/Disable

Jumper

J1: SATA3 Ports

UP: Port 1

Down: Port 0

J2:

LED

Connector

J3: SATA3 Ports

UP: Port 3

Down: Port 2

4-Port SATA3 RAID/HyperDuo PCIe(x2) Card

The JP1 can be used to disable the BIOS on the card for some critical

applications, please leave the jumper at “ENA” all the time.

JP1: BIOS Enable/Disable Jumper

1. Power down the computer, remove the computer cover.

2. Choose an unused PCI Express bus slot (2, 4, 8 or 16 lane), unscrew and

remove the slot cover.

3. Place the SATA3 RAID PCIe Card into the slot. Carefully press the board

into the slot until it seats firmly.

4. Secure the SATA3 RAID PCIe Card with the slot cover screw.

5. Install the SATA cables from the SATA connectors to your SATA devices.

6. Carefully reinstall the computer cover. Insert and tighten the computer

cover screws.

7. Power up the PC and observe the monitor. The BIOS lists all Serial ATA

devices attached to the SATA3 RAID/HyperDuo PCIe Card. For example:

4. Ha

rdware Installation

BIOS Enabled:

Jumper Installed at “ENA”

(Default)

BIOS Disabled:

Jumper Installed at “DIS”

3. Jumper Settings

DIS ENA

4-Port SATA3 RAID/HyperDuo PCIe(x2) Card

If the information displayed on your monitor is correct (the installed

devices are listed with the correct device name, etc.), congratulations!

You have successfully installed the SATA3 RAID/HyperDuo PCIe Card in

your computer. If you want to configure your RAID drives, press and hold

the 2 keys, and , to enter the BIOS Setup Utility for this card. You can Ctrl M

configure the SATA RAID or HyperDuo modes in the BIOS Setup.

5.1 RAID Modes

This chapter will help you to know the RAID and HyperDuo modes

supported by the SATA3 RAID/HyperDuo PCIe Card.

5.2 Non-RAID mode (Single Disk Mode)

This mode is the Single Disk mode. Each disk drive will be treated as

one disk volume in the operating system.

5.3 Striping (RAID 0)

Read and write sectors of data interleaved between multiple drives.

When any disk member fails, it affects the entire array. Performance is

better than a single drive since the workload is balanced between

the array members. This array type is for high performance systems.

Identical drives are recommended (but not necessary, if the sizes

differ, it will truncate the bigger drive so the sizes match, it will cause a

waste) for performance as well as data storage efficiency. The disk

array data capacity is equal to the number of drive members times

the smallest member capacity.

5. RAID and HyperDuo Modes

Product specificaties

Merk:	EXSYS
Categorie:	Controller
Model:	EX-3516
Gewicht:	300 g
Diepte:	79 mm
Hoogte:	48 mm
Certificering:	CE / FCC
Ondersteunt Windows:	Windows 7 Home Premium, Windows 7 Home Premium x64, Windows 8, Windows 8 x64, Windows Vista Home Premium, Windows Vista Home Premium x64, Windows XP Home, Windows XP Home x64
Temperatuur bij opslag:	-40 - 75 °C
PCI Express slots versie:	1.0
Spanning:	3.3 V
Ondersteunde opslagstationinterfaces:	SATA III
Hot-plug ondersteuning:	Ja
Chipset:	Marvell 88SE9230-NAA2
Soorten RAID:	0, 1
Overdrachtssnelheid:	6 Gbit/s
Bedrijfstemperatuur (T-T):	0 - 55 °C
Relatieve vochtigheid in bedrijf (V-V):	5 - 95 procent
Hot-swap:	Ja
Aantal Internal SATA ports:	4