EXSYS EX-3515 Handleiding

EXSYS Controller EX-3515

Lees hieronder de 📖 handleiding in het Nederlandse voor EXSYS EX-3515 (10 pagina's) in de categorie Controller. Deze handleiding was nuttig voor 34 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/10

Thank you for purchasing this 2-Port SATA3 RAID/HyperDuo PCIe

Card. It is designed to support up to 2 SATA3 ports in RAID 0 and

RAID 1 modes and HyperDuo modes for SSD (Solid State Drive) and

hard drive combination. It supports SATA3 SSD and hard drives with

up to 6.0Gbps data rate. It is an ideal solution to add new SATA3 SSD

and hard drives for your system.

Features:

 Supports 1-lane 5.0Gb/s PCI Express Gen.2 Data Transfer Rate

 Built-in 2 Internal SATA3 Ports

 Supports RAID 0, RAID 1, HyperDuo (Safe or Capacity) Modes

 Supports Windows based RAID GUI (Marvell Storage Utility, MSU)

 Supports SATA3 transfer rate up to 6.0Gb/s (600Mbytes/sec)

 Supports RAID 1 Rebuild by BIOS Setup Utility

 Supports Windows 2003, 2008, XP, Vista and Win 7

EX-3515

2-Port SATA3 RAID/HyperDuo PCIe Card

1. Introduction

2. Board Layout

JP1 BIOS

Enable/Disable

Jumper

J2:

SATA3

Channel 1

J1:

SATA3

Channel 0

Extra secure

mounting

holes

2-Port SATA3 RAID/HyperDuo PCIe Card

The JP1 can be used to disable the BIOS on the card for some

critical applications, please leave the jumper at “ENA” all the time.

JP1: BIOS Enable/Disable Jumper

1. Power down the computer, remove the computer cover.

2. Choose an unused PCI Express bus slot, unscrew and remove the slot

cover.

3. Place the SATA3 RAID PCIe Card into the slot. Carefully press the

board into the slot until it seats firmly.

4. Secure the SATA3 RAID PCIe Card with the slot cover screw.

5. Install the SATA cables from the SATA connectors to your SATA devices.

6. Carefully reinstall the computer cover. Insert and tighten the

computer cover screws.

7. Power up the PC and observe the monitor. The BIOS lists all Serial ATA

devices attached to the SATA3 RAID/HyperDuo PCIe Card. For

example:

Marvell 88SE91xx Adapter – BIOS Version x.x.x.xxxx

PCIe p2-x1 5.0Gbps

Mode: CPU AHCI

Virtual Disk

No Virtual Disk!

Physical Disk

[ID] [DISK Name] [Size] [Speed]

0 SATA ST32000641AS 1.83TB 6.0G

1 SATA ST32000641AS 1.83TB 6.0G

Press <Ctrl>+<M> to enter BIOS Setup or <Space> to continue

If the information displayed on your monitor is correct (the installed

devices are listed with the correct device name, etc.), congratulations!

You have successfully installed the SATA3 RAID/HyperDuo PCIe Card in

4. Hardware Installation

BIOS Enabled:

Jumper Installed at “ENA”

(Default)

BIOS Disabled:

Jumper Installed at “DIS”

3. Jumper Settings

ENA DIS

2-Port SATA3 RAID/HyperDuo PCIe Card

your computer. If you want to configure your RAID drives, press and

hold the 2 keys, Ctrl M and , to enter the BIOS Setup Utility for this card.

You can configure the SATA RAID or HyperDuo modes in the BIOS

Setup.

5.1 RAID Modes

This chapter will help you to know the RAID and HyperDuo modes

supported by the SATA3 RAID/HyperDuo PCIe Card.

5.2 Non-RAID mode (Single Disk Mode)

This mode is the Single Disk mode. Each disk drive will be treated as

one disk volume in the operating system.

5.3 Striping (RAID 0)

Read and write sectors of data interleaved between multiple drives.

When any disk member fails, it affects the entire array. Performance

is better than a single drive since the workload is balanced

between the array members. This array type is for high performance

systems. Identical drives are recommended (but not necessary, if

the sizes differ, it will truncate the bigger drive so the sizes match, it

will cause a waste) for performance as well as data storage

efficiency. The disk array data capacity is equal to the number of

drive members times the smallest member capacity.

5.4 Mirroring (RAID 1)

Writes duplicate data on to a pair of drives while reads are

performed in parallel. The RAID controller performs reads using

advanced data handling techniques that distribute the workload in

a more efficient manner than using a single drive. When a read

Write data Streams

… ….. 4, 3, 2, 1

Read data Streams

….. 4, 3, 2, 1

Stripe member 1

Stripe member 2

5. RAID and HyperDuo Modes

Product specificaties

Merk:	EXSYS
Categorie:	Controller
Model:	EX-3515
Gewicht:	300 g
Breedte:	115 mm
Diepte:	48 mm
Ondersteunt Windows:	Ja
Temperatuur bij opslag:	-40 - 75 °C
Ondersteunde opslagstationinterfaces:	SATA III
Soorten RAID:	0, 1
Bedrijfstemperatuur (T-T):	0 - 55 °C
Relatieve vochtigheid in bedrijf (V-V):	5 - 95 procent
Aantal Internal SATA ports:	2
SSD-ondersteuning:	Ja