EMOS P5760 Handleiding

EMOS Deurbel P5760

Lees hieronder de 📖 handleiding in het Nederlandse voor EMOS P5760 (74 pagina's) in de categorie Deurbel. Deze handleiding was nuttig voor 3 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/74
3402060000_31-P5760_00_01_WEB 80 × 120 mm
www.emos.eu
P5760
GB Wireless Doorchime & Repeater
CZ Bezdrátový zvonek & prodlužovač signálu
SK Bezdrôtový zvonček & predovač signálu
PL Dzwonek bezprzewodowy & repeater sygnału
HU Vezeték nélküli csengő és jelismétlő
SI Brezžični zvonec in ojačevalnik signala
RS|HR|BA|ME Bežično kućno zvono i repetitor
DE Drahtlose Klingel und Signalverngerung
UA Бездротовий дзвоник & подовжувач сигналу
RO|MD Sonerie fă r & prelungitor de semnal
LT Belaidis duskambutis ir retransliatorius
LV Bezvadu durvju zvans un atkārtotājs
EE Juhtmevaba uksekell ja repiiter
BG Безжичен звънец и повторител
FR Carillon sans l & prolongateur de portée
IT Campanello senza li & ripetitore di segnale
ES Timbre inambrico & repetidor de sal
NL Draadloze deurbel & signaalverlenger
2
1
25
6
3
4
A B C
1
2
3
GB | Wireless Doorchime & Repeater
The set consists of a doorchime button (transmitter) and a chime (receiver). The chime is deigned for constant
connection to a 230 V AC/50 Hz power network. The transmission between the button and the chime is done
via radio waves at a frequency of 433.92 MHz. The range depends on local conditions and reaches up to 120 m
in open spaces without interference.
The set has a so-called „self-learning“ function the button is able to generate its own pairing code which is
then received by the chime and stored in its memory. The set can thus be expanded with additional buttons.
Their „self-learning“ function also prevents them from aecting neighbouring doorchimes.
The range of the button can be extended using the „repeater“ function (signal repeater).
For proper usage of the wireless doorchime, read the instruction manual thoroughly.
Technical Specications
Transmission range: up to 120 m in an open area (can drop down to one fth in a busy area)
Button: water resistant; enclosure IP44
3
Pairing of chime and buttons: „self-learning“ function
Pairing capacity: maximum of 8 buttons per 1 chime
Number of ringtones: 16
Transmission frequency: 433.92 MHz, 5 mW e.r.p. max.
Chime power supply: 230 V AC/50 Hz
Button power supply: 1× 3 V battery (type CR2032, included)
USB connector: output max. 5 V, 2 A
Includes: double-sided adhesive tape, screws
Chime Description (see Fig. 1)
1 – chime LED
2 – ringing mode button
3 – volume settings button
4 – repeater button (signal repeating)
5 – speaker
6 – USB connector (used for charging compatible devices, see Technical Specications).
Button Description (see Fig. 2)
A – battery
B – button for changing ringtone/erasing memory of paired buttons
C – ring button/LED
Opening the Rear Compartment of the Button (see Fig. 3)
Pairing the Button with the Chime
1. Remove the rear cover of the button with a screwdriver through the hole on the side (see Fig. 3).
Insert a 3 V battery, type CR2032, into the button. When inserting the battery, make sure to observe correct
polarity (+ polarity up)!
2. Plug the chime into a 230 V AC/50 Hz socket. You will hear a „ding dong“ tone.
The chime automatically switches to „self-learning“ mode which lasts for 60 second.
3. During these 60 seconds, press the button you want to pair with the chime. If the chime receives signal
from the button, a tone will sound, the button will pair with the chime and the self-learning mode will
automatically end.
4. For pairing multiple buttons, repeat steps 1 to 3.
Note: Before pairing each button, the chime must be put into self-learning mode unplug and plug into
a 230 V socket.
You can pair a maximum of 8 buttons per chime this way.
Note: The chime has an internal memory where it stores the codes of the currently paired buttons for cases of
power failure. Once power supply to the chime is restored, the chime will automatically enter self-learning mode
for 60 seconds. However, if no signal is received within these 60 seconds (new pairing is not performed), the
chime will automatically load the codes of the previously paired buttons after self-learning mode ends. There
is thus no need to pair buttons again after a power failure.
Wiping the Memory of Paired Buttons
Remove the rear cover of the button with a screwdriver through the hole on the side.
1. Set the chime to pairing mode – unplug the chime from the socket and replug it again; a tone will sound.


Product specificaties

Merk: EMOS
Categorie: Deurbel
Model: P5760

Heb je hulp nodig?

Als je hulp nodig hebt met EMOS P5760 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Deurbel EMOS

EMOS

EMOS P5727T Handleiding

2 December 2024
EMOS

EMOS P5728 Handleiding

2 December 2024
EMOS

EMOS P5750.2R Handleiding

2 December 2024
EMOS

EMOS P5750T Handleiding

2 December 2024
EMOS

EMOS P5760 Handleiding

2 December 2024
EMOS

EMOS P5733G Handleiding

2 December 2024
EMOS

EMOS P5760T Handleiding

2 December 2024
EMOS

EMOS P5730 Handleiding

2 December 2024
EMOS

EMOS P5750.2T Handleiding

2 December 2024
EMOS

EMOS P5705 Handleiding

2 December 2024

Handleiding Deurbel

Nieuwste handleidingen voor Deurbel