Emmeti CS11-U9132010-015 Handleiding

Emmeti Thermostaat CS11-U9132010-015

Lees hieronder de 📖 handleiding in het Nederlandse voor Emmeti CS11-U9132010-015 (2 pagina's) in de categorie Thermostaat. Deze handleiding was nuttig voor 55 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2



TAE S13 MC0 0MB 018080A1 140610





Suitable for 230 V~ or 24 V~ operation with switching load up to 5

(1) amps.

Red LED light shows when the thermostat is calling for heat.

Optional remote sensors - enables thermostat use in bathroom

applicatons.

Simple to use dial operation with clear temperature settings from 6 °C to 30 °C.

Wall mounted thermostat in elegant white design, only 85 mm wide x 85 mm high x 31 mm deep.

Accurate temperature control for maximum comfort - differential 0.5 °C.

Temperature range limiting stops to prevent accidental adjustment.

Compliant with directives EEC 89/336, 73/23 & 93/68 (CE)

6 Tannery Yard - Witney Street - Burford

Oxfordshire - OX18 4DW - UK

Phone: 01993 824900

Fax: 01993 824990

Email: sales@emmeti.co.uk

Website: www.emmeti.co.uk











Cable Aperture

38 mm

10 mm

43 mm

82 mm

60 mm

41 mm

82 mm











This electronic room thermostat (Fig. 1) is suitable

for reliable and accurate temperature regulation in

commercial and industrial premises as well as for

home installation.



When the measured room temperature is below the

value set on the dial the thermostat turns the relay

on and, at the same time, turns the red LED on for

’Heating’.





The user can set the room temperature by moving

the dial to any desired temperature between

6°C and 30°C, in one degree steps, against the

index mark next to the dial at the 9 o'clock position.









The thermostat should be positioned about 1.5m

from floor level and must avoid being positioned

near draughts, sources of heat or cold or direct

sunlight. To install the thermostat:

First remove the dial by inserting a small

screwdriver in the slot (2) and lifting the dial off

carefully.

Remove the front cover by disengaging the two

plastic teeth on the right hand side of the case

as shown in figs. 2 & 3.

The thermostat has been designed for fixed

wiring only. Cable access is through the rear of

the mounting backplate as shown in Fig. 4

The backplate can be secured either to a flat

vertical mounting surface or to a single gang flush

mounted wiring box: the fixing centres are shown in

Fig. 4

Fix the thermostat backplate to the wall through

the two screw holes with distance between

centres of 60 mm.

Make the wiring connections to the backplate as

shown in fig. 5 including any remote sensor

connections to terminals 6 and 7.

When the electrical connections are complete,

refit the cover by aligning the four plastic teeth

on the backplate with the holes in the cover and

then press gently to snap them together. Refit

the dial aligning the 'D' shape to the spindle.





It is possible to limit the rotation range for the dial

by following these steps:

First remove the dial by inserting a small

screwdriver in the slot (2) and lifting the dial off

carefully.

Pick up the plastic pins (4) parked to the left of

the knob area and set them (5) as shown in of

Fig. 6. In this example the rotation range (6) is

reduced to the angle shown.



When using the remote sensor option with the

thermostat, connect the sensor as shown in Fig. 5

() and remove the jumper on the bottom right hand

corner of the backplate - see fig. 7. Cased remote

sensors must be connected in cable of at least

1.5mm2cross sectional area and not greater than

25m in length. Do not put mains cables and sensor

cables next to one another.



Power supply:

U9 132 015: 230V~ -15% +10% 50Hz

U9 132 010: 24V~/= -15% +10% 50Hz

Power absorption: 1VA

Regulation range: 6°C .. 30°C

Sensor type: NTC 4,7k @ 25°C

internal

Remote sensor optional: U9 132 011

U9 132 012

Contact rating: 5 (1) A @ 250V~ SPDT

Protection grade: IP 30

Operating temperature: 0°C .. 40°C

Storage temperature: -10°C .. +50°C

Humidity limits: 20% .. 80% RH

(non condensing)

Case: Material: ABS self extinguishing V0

Color: Signal white (RAL 9003)

Size: 85 x 85 x 31 mm (W x H x D)

Weight: U9 132 015: ~135 gr.

U9 132 010: ~ 130 gr.

In view of the constant development of their products,

the manufacturer reserves the right to change technical

data and features without prior notice. The consumer is

guaranteed against any lack of conformity in accordance

with the European Directive 1999/44/EC as well as the

manufacturer’s own warranty policy. The full text of the

warranty is available on request from Emmeti UK Ltd.

TAE S13 MC0 0MB 018080A1 140610



TAE S13 MC0 0MB 018080A1 140610





Suitable for 230 V~ or 24 V~ operation with switching load up to 5

(1) amps.

Red LED light shows when the thermostat is calling for heat.

Optional remote sensors - enables thermostat use in bathroom

applicatons.

Simple to use dial operation with clear temperature settings from 6 °C to 30 °C.

Wall mounted thermostat in elegant white design, only 85 mm wide x 85 mm high x 31 mm deep.

Accurate temperature control for maximum comfort - differential 0.5 °C.

Temperature range limiting stops to prevent accidental adjustment.

Compliant with directives EEC 89/336, 73/23 & 93/68 (CE)

6 Tannery Yard - Witney Street - Burford

Oxfordshire - OX18 4DW - UK

Phone: 01993 824900

Fax: 01993 824990

Email: sales@emmeti.co.uk

Website: www.emmeti.co.uk











Cable Aperture

38 mm

10 mm

43 mm

82 mm

60 mm

41 mm

82 mm











This electronic room thermostat (Fig. 1) is suitable

for reliable and accurate temperature regulation in

commercial and industrial premises as well as for

home installation.



When the measured room temperature is below the

value set on the dial the thermostat turns the relay

on and, at the same time, turns the red LED on for

’Heating’.





The user can set the room temperature by moving

the dial to any desired temperature between

6°C and 30°C, in one degree steps, against the

index mark next to the dial at the 9 o'clock position.









The thermostat should be positioned about 1.5m

from floor level and must avoid being positioned

near draughts, sources of heat or cold or direct

sunlight. To install the thermostat:

First remove the dial by inserting a small

screwdriver in the slot (2) and lifting the dial off

carefully.

Remove the front cover by disengaging the two

plastic teeth on the right hand side of the case

as shown in figs. 2 & 3.

The thermostat has been designed for fixed

wiring only. Cable access is through the rear of

the mounting backplate as shown in Fig. 4

The backplate can be secured either to a flat

vertical mounting surface or to a single gang flush

mounted wiring box: the fixing centres are shown in

Fig. 4

Fix the thermostat backplate to the wall through

the two screw holes with distance between

centres of 60 mm.

Make the wiring connections to the backplate as

shown in fig. 5 including any remote sensor

connections to terminals 6 and 7.

When the electrical connections are complete,

refit the cover by aligning the four plastic teeth

on the backplate with the holes in the cover and

then press gently to snap them together. Refit

the dial aligning the 'D' shape to the spindle.





It is possible to limit the rotation range for the dial

by following these steps:

First remove the dial by inserting a small

screwdriver in the slot (2) and lifting the dial off

carefully.

Pick up the plastic pins (4) parked to the left of

the knob area and set them (5) as shown in of

Fig. 6. In this example the rotation range (6) is

reduced to the angle shown.



When using the remote sensor option with the

thermostat, connect the sensor as shown in Fig. 5

() and remove the jumper on the bottom right hand

corner of the backplate - see fig. 7. Cased remote

sensors must be connected in cable of at least

1.5mm2cross sectional area and not greater than

25m in length. Do not put mains cables and sensor

cables next to one another.



Power supply:

U9 132 015: 230V~ -15% +10% 50Hz

U9 132 010: 24V~/= -15% +10% 50Hz

Power absorption: 1VA

Regulation range: 6°C .. 30°C

Sensor type: NTC 4,7k @ 25°C

internal

Remote sensor optional: U9 132 011

U9 132 012

Contact rating: 5 (1) A @ 250V~ SPDT

Protection grade: IP 30

Operating temperature: 0°C .. 40°C

Storage temperature: -10°C .. +50°C

Humidity limits: 20% .. 80% RH

(non condensing)

Case: Material: ABS self extinguishing V0

Color: Signal white (RAL 9003)

Size: 85 x 85 x 31 mm (W x H x D)

Weight: U9 132 015: ~135 gr.

U9 132 010: ~ 130 gr.

In view of the constant development of their products,

the manufacturer reserves the right to change technical

data and features without prior notice. The consumer is

guaranteed against any lack of conformity in accordance

with the European Directive 1999/44/EC as well as the

manufacturer’s own warranty policy. The full text of the

warranty is available on request from Emmeti UK Ltd.

TAE S13 MC0 0MB 018080A1 140610

Product specificaties

Merk:	Emmeti
Categorie:	Thermostaat
Model:	CS11-U9132010-015

Heb je hulp nodig?

Als je hulp nodig hebt met Emmeti CS11-U9132010-015 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Thermostaat Emmeti

Emmeti CS11-U9132016-013 Handleiding

30 Januari 2023

Emmeti CS11-U9132010-015 Handleiding

30 Januari 2023

Emmeti CS-11 - U9310044 Handleiding

30 Januari 2023

Emmeti CS-11- U9310020 Handleiding

30 Januari 2023

Handleiding Thermostaat

Nieuwste handleidingen voor Thermostaat

Tru Components TCN4S-24R Handleiding

18 December 2024

Tru Components TK4S-14RC Handleiding

18 December 2024

Tru Components TX4S-14R Handleiding

17 December 2024

Warmup 5iE Handleiding

16 December 2024

Warmup +Kit Handleiding

16 December 2024

Nobo Connect SWT-IZW Handleiding

15 December 2024

Nobo Connect SWT-IZB Handleiding

11 December 2024

Hive Thermostat Handleiding

10 December 2024

GENERAL Life HT15S Handleiding

9 December 2024

GENERAL Life HT15 Handleiding

9 December 2024