Emerson PowerSure Personal XT Handleiding

Emerson UPS PowerSure Personal XT

Lees hieronder de 📖 handleiding in het Nederlandse voor Emerson PowerSure Personal XT (12 pagina's) in de categorie UPS. Deze handleiding was nuttig voor 33 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/12

450, 700, 1250 VA

230V

PowerSureTM Personal XT

U MSER ANUAL

English / Deutsch / Français /

Italiano / Español

PS PXT-inglese.qxd 6-06-2001 9:51 Pagina 1

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

This manual contains important safety instructions that should be followed during

the installation and maintenance of the UPS and its batteries. Please read this

manual thoroughly before attempting to install or operate this UPS.

This equipment can be installed and operated by individuals without previous

training.

1. PowerSure Personal XT models are available for 230VAC supply voltages and

loads. Please verify that this model matches your AC mains/ load voltage

requirements.

2. This equipment is designed for Commercial/Industrial use only. Liebert

Corporation neither recommends nor knowingly sells this product for use in

critical life support applications.

3. The PowerSure Personal XT 230VAC models are not supplied with an input

power lead for connection to the mains supply. Use the input mains power

lead from your data processing equipment to connect the UPS to the mains

supply. The UPS is supplied with two output power leads with moulded

connectors to connect from the UPS output to your equipment. Additional

input/output leads can be obtained from your dealer.

Also provided is a Liebert special interconnection cable for connection to

DB9 connector on the rear of the UPS for use with Liebert's SiteNet

MultiLink® software (see user manual for details) DO NOT USE FOR

OTHER APPLICATIONS. Store in safe place if not required at this time.

4. This UPS must be earthed at all times during operation. Connect only to a

mains supply socket outlet with an earth connection. A means of disconnection of

the mains supply should be within 2 metres of the UPS.

5. WARNING: Output receptacles on the UPS are electrically live if the UPS is

switched ON, even if the UPS is not plugged in to a mains supply. The

On/Off button on the UPS does not electrically isolate the internal parts. To

isolate the UPS, switch OFF the UPS first, then unplug it from the mains.

.To reduce the risk of electric shock, do not remove the cover, as it has no

user-serviceable parts inside. Some components are live, even when AC

power is disconnected. For service, contact a qualified technician.

.To reduce the risk of fire, use the proper rating when replacing the fuse.

.To prevent the risk of fire or electric shock, install the UPS in a temperature

and humidity controlled room, free of conductive contaminants.

6. Your total load earth leakage current must not exceed 3.5 milli-amperes.

Most data processing equipment meets this requirement if you use no more

than 2 pieces of equipment. For further advice contact your dealer.

7. The UPS relies on your building wiring overcurrent protection, which must be

rated between 10-20 amperes.

8. When using the communication features on the UPS, ensure the cabling

connected to the DB9 communication port or the network connection are

kept separated by 25mm from the power leads to the UPS input and output.

PS PXT-inglese.qxd 6-06-2001 9:51 Pagina 2

These units bear TUV GS mark, CE mark and comply with the following standards

(limits value class B):

EN 60950 (1998.8),

EN 50091-1 (1994.4),

EMI/RFI: EN550222 class B

EMS: IEC 1000-4-2 (ESD) Level 3

IEC 1000-4-3 (RS) Level 3

IEC 1000-4-4 (EFT) Level 3

IEC 1000-4-5 (Lightning surge) Level 3

CAUTION:

Although your UPS has been designed and manufactured to assure personal

safety, improper use can result in electrical shock or fire. To insure safety,

please observe the following rules:

.Turn off and unplug your UPS before cleaning. Do not use liquid or aerosol

cleaners. A dry cloth is recommended to remove dust from the surface of

your UPS.

.Do not install or operate your UPS in or near water.

.Do not place UPS on an unstable cart, stand, or table.

.Do not place UPS under direct sunlight or close to heat emitting sources.

.Do not place UPS power cord in any area where it may get damaged by

heavy objects.

.Follow all warnings and instructions marked on the UPS. Do not attempt to

service the UPS, as it has no user-serviceable parts inside. Refer all repairs

to qualified service personnel.

ATTENTION:

Turn off and unplug your UPS from the outlet and contact qualified service

personnel if:

.The power cord or plug is damaged.

.Liquid has been spilled on the UPS.

.The fuse blows frequently.

.The UPS does not operate even when user follows the operating instructions.

CONDITIONS OF USE:

Your UPS provides conditioned power to connected equipment. Maximum load

must not exceed that shown on UPS rating label. If uncertain, consult your

distributor or Liebert.

Placing magnetic storage media on top of the UPS may result in data corruption.

PS PXT-inglese.qxd 6-06-2001 9:51 Pagina 3

Product specificaties

Merk:	Emerson
Categorie:	UPS
Model:	PowerSure Personal XT
Gewicht:	3500 g
Gewicht verpakking:	4500 g
Afmetingen verpakking (BxDxH):	155 x 270 x 300 mm
Uitgangsvermogen:	270 W
Temperatuur bij opslag:	-15 - 40 °C
Afmetingen (B x D x H):	80 x 233 x 176.5 mm
Bedrijfstemperatuur (T-T):	0 - 40 °C
Relatieve vochtigheid in bedrijf (V-V):	20 - 90 procent
Output power capacity:	0.45 kVA
Output-aansluitingen:	3 x EN60320/C13