Elektrobock PT712-EI Handleiding

Elektrobock Thermostaat PT712-EI

Lees hieronder de 📖 handleiding in het Nederlandse voor Elektrobock PT712-EI (8 pagina's) in de categorie Thermostaat. Deze handleiding was nuttig voor 24 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/8

MADE IN CZECH REPUBLIC

•including external sensor

•backup in case of voltage failure > 100 hours

•direct installation on junction box

•well-arranged backlit display

VENUS switch design

N L COM NO N L COM NO

DESCRIPTION

PT712-EI is a digital thermostat with a room and ﬂ oor sensor, specially designed for electric ﬂ oor heating

control. The internal-external sensor combination enables the regulation of:

1) ﬂ oor temperature (external sensor) - suitable, for instance, for bathrooms where a warm ﬂ oor is

desirable, irrespective of the room temperature;

2) room temperature (internal sensor) - when comfortable room temperature is required;

3) combined (both sensors) - the internal sensor scans the room temperature, while the

external one monitors the maximum ﬂ oor temperature;

comfortable room temperature is required, however, with

simultaneous monitoring of the ﬂ oor temperat (suitable for wooden

and laminated ﬂ oors).

Another advantage is simple installation in the KU/KP68 junction boxes by means of the PLUG-IN

system, as well as the possibility of setting 2 weekly programs with 6 temperature changes per day.

INSTALLATION AND LOCATION

Install the thermostat in a suitable place (minimum height of 1.2-1.5 m above the ﬂ oor) where its operation

will not be affected by direct hot/cold air ﬂ ow, sunshine or other disturbing inﬂ uences. Do not mount the

thermostat on an exterior wall either. In rooms with increased humidity (bathroom, kitchen), observe valid

standards and install the thermostat as far from the bathtub, shower, basin or sink as possible.

The external ﬂ oor sensor (type CT04-10k, CYXY 2 x 0.5 mm, 10 k:, lenght 3 m, PVC plastic case)

must be located in a ﬂ exible plastic tube embedded in the ﬂ oor, as near to the surface as possible. The

tube must be sealed and protected against in-leak of building materials so that the ﬂ oor sensor can be

replaced easily, if need be. It must not run parallel with power conductors! It can be extended to

a maximum length of 30 metres. The installation can only be done by a properly qualiﬁ ed person!

Disconnect power supply before installation!

1) Switch off the main circuit breaker.

2) Check that the junction box is placed parallel with the wall.

3) Separate the power part of the thermostat from its microprocessor (main) part; see Fig. 1.

4) Pull the connecting terminals out of the thermostat rear part, see Fig. 2.

5) Connect conductors to the terminals acc. to the wiring diagram below, see Fig. 3.

6) Insert the terminals into the thermostat terminals and fasten the power part to the junction

box, see Fig. 4 and 5.

7) Insert the main part connector into the power part and push it; the metal springs must

ﬁ t in the given holes, see Fig. 6 and 7.

8) Switch on the main circuit breaker; the thermostat is ready for operation. LCD backlight becomes active only

after charging the backup battery (up to 24 hours).

9) Set the constant 4 (page 6) according to the load, this could cause an inaccurate display of the current

temperature.

Note: We recommend you test correct connection after installation, see the TEST function (page 7).

Wiring diagram: Fig. 1

When using the low tariff

L‘ = disconnected phase

power part main part

PULLPULL

connecting

terminals

HEATING

NTC 10k NTC 10k

* P= max. 2760 W

DESCRIPTION OF LCD AND CONTROL BUTTONS

1, Current date (in the Prog mode, selection of number of days for

programming)

2, Operating modes: OFF/PROG/AUTO/MANU/case=HOLIDAY

3, Current room temperature

4, Indication of room temp. measurement by the exter. sensor.

5, Heating on indication

6, Button lock indication

7, CLOC mode indication (current date and time setting)

8, Required temperature and current time display / listing of operating

modes (this line is explained in detail with every mode)

9, Battery supply indication (in case of 230V/50Hz voltage failure,

it is functional only after 1 day of operation, when the backup

battery is charged!)

10, Indication of setting the external sensor as the ﬂ oor one

11, Anti-freeze temperature of 3 °C

MENU button:

short press = opens the main menu and

conﬁ rmation (ENTER)

long press (approx. 3 sec.) = back from the

main menu

/ button:

basic mode = opens info

main menu =browse and set current values

simultaneous press of the MENU and

buttons (in basic mode) = key lock

simultaneous press of the MENU and

buttons (in basic mode) = key unlock

simultaneous press of the MENU and /

buttons (in main menu) = return to basic mode

Note: The LCD backlight is activated by pres-

sing any button!

Fig. 2 Fig. 3 Fig. 4

Fig. 5 Fig. 6 Fig. 7

NO COM

PULL out the connecting terminals. Connect according to the wiring diagram.

PUSH the connecting

terminals in.

Screw the power part to

the junction box.

Connector and holes

for metal springs.

PUSH the

main part

onto the

power part.

Product specificaties

Merk:	Elektrobock
Categorie:	Thermostaat
Model:	PT712-EI

Heb je hulp nodig?

Als je hulp nodig hebt met Elektrobock PT712-EI stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Thermostaat Elektrobock

Elektrobock BT730 Handleiding

12 Maart 2024

Elektrobock PT 32 GST Handleiding

11 September 2023

Elektrobock BPT 32 Handleiding

11 September 2023

Elektrobock PT 14 Handleiding

11 September 2023

Elektrobock PT 713 EI Handleiding

11 September 2023

Elektrobock PT 713 Handleiding

11 September 2023

Elektrobock BPT 22 Handleiding

11 September 2023

Elektrobock BT710 Handleiding

24 Juni 2023

Elektrobock BT102 Handleiding

6 Juni 2023

Elektrobock PT01 Handleiding

13 Mei 2023

Handleiding Thermostaat

Nieuwste handleidingen voor Thermostaat

Techno Line TM 3010 Handleiding

18 November 2024

Ferguson FS1TH Handleiding

17 November 2024

EQ-3 HM-RC-19 Handleiding

16 November 2024

EQ-3 CC-RT-N Handleiding

16 November 2024

Delta Dore TYDOM 1.0 Handleiding

16 November 2024

Delta Dore Tybox 5701 FP Handleiding

16 November 2024

Delta Dore Tybox 33 Handleiding

16 November 2024

Delta Dore Tybox 5702 FP Handleiding

16 November 2024

Delta Dore Tybox 31 Handleiding

16 November 2024

Delta Dore TYBOX 827 W RF Handleiding

16 November 2024