Elektrobock BT102 Handleiding

Elektrobock Thermostaat BT102

Lees hieronder de 📖 handleiding in het Nederlandse voor Elektrobock BT102 (6 pagina's) in de categorie Thermostaat. Deze handleiding was nuttig voor 57 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/6

MADE IN CZECH REPUBLIC

The great advantage is the possibility of changing the reference room by simply relocating the transmitter

part, in which way an optimum temperature comfort can be achieved in the room heated. The coverage

of the set can reach up to 35 m. The receiver is equipped with a code self-learning system and the

E-EPROM memory, which can keep the code saved even at power failure. The possibility of setting up

to 4 time periods and temperatures for every day provides for optimum distribution of electric energy

for all week. An ideally selected program will help you to reduce heating costs by up to 30 %.

• Receiver power supply 230 V/ 50 Hz.

• Receiver with the CODE SELF-LEARNING

system and the E-EPROM memory (saving

the code even at power failure).

• Two-wire connection to the boiler.

• Indication LED for signalization of the

states

- power supply indication

- signal transmission / reception

- failure state

- relay closed.

receiver – wall-mounted

transmitter

• Weekly program

• 4 temperature changes per every day

• Programming by 30 minutes and 0.5 °C

• Programming by day or Mon-Fri, Sat-Sun

or Mon-Sun

• Hysteresis 0.5 °C

• Possibility of short-term temperature

change

• Key lock

• Sum of boiler operating hours

• Manual mode (MANU)

• Permanent switch-off (OFF)

• Anti-freeze mode (3 °C)

• TEST function

• Supplied by alkaline batteries

2 × 1.5 V/AA

- freely portable

- small dimensions

- simple operation

- possibility of using

the stand (included

in the delivery)

TWO-WAY COMMUNICATION

- providing for reliable signal transmission and

enabling return information acquisition.

RECEIVER CONTROL ELEMENTS

CODE LEARNING

230 V/50Hz

To be used if the receiver memory has been erased – the red diode is ﬂ ashing!

1) Push the receiver’s “FUNCTION BUTTON” for about 1.5 sec; the blue and red LEDs start

ﬂ ashing alternately; and the receiver is awaiting the code (“learning mode”).

2) After insetting batteries into the transmitter (see page 3), push the Fce , button; select the tE:St

function with the / button and conﬁ rm it with the i button (the message appears on the Ad:r

display); conﬁ rm with the i button (the code will be sent to the receiver).

3) The code receipt in the receiver is indicated by simultaneous ﬂ ashing of the blue and red LED; thus the

code has been learnt. After the code receipt, the output relay is switched several times to verify correct

function of BPT 102 (On/OFF is displayed on the transmitter).

Lifting off the front cover:

Fig.1 Fig.2

Indication LEDs:

GREEN LIT - correct connection to the mains

BLUE FLASHES shortly - during communication with the transmitter

RED FLASHING - empty E-EPROM memory

RED LIT - FAILURE (if no signal from the transmitter is received within approx. 6

hours, it switches to the “2-min-ON / 8-min-OFF” mode)

BLUE+ FLASHING ALTERNATELY - code learning modeRED

BLUE+ FLASHING SIMULTANEOUSLY - code has been learnedRED

BLUE+ LIT SIMULTANEOUSLY - memory erasure modeRED

ORANGE LIT - relay 1 switched

holes for mounting on KU/KP68

FUNCTION BUTTON

- short push (approx. 1 s) =

CODE-LEARNING mode

- long push (approx. 5 s) =

RESET (memory erasure)

output terminals for

the boiler

(potential-free

switching contact)

power supply

terminals

RECEIVER INSTALLATION

- Lift off the front cover of the receiver acc. to Fig. 1, 2.

- Fix the receiver to the wall (or directly to the wiring box).

- Switch off the main circuit breaker.

- Connect the receiver to the boiler according to the diagram (on the boiler, use the terminals for wires of

the room thermostat 2).

- Connect the receiver to the mains 230 V / 50 Hz.

- Switch on the main circuit breaker; the green LED lights up on the receiver; thus the receiver is ready

for further setting

Owing to disturbance of the signal reception, install the receiver (in the interior) as far as possible (no

less than 0.5 m) from big metal objects and outside high-current power lines! We recommend that the

installation be done by a person properly qualiﬁ ed in electrical engineering!

Wiring diagram: BOILER

BATTERY REPLACEMENT

The necessity to replace the batteries is indicated by the “ bA:tt “

symbol ﬂ ashing on the display.

1) Remove the control part from the lower cover of the device (Fig. 5).

2) Replace the batteries. Heed the correct polarity indicated in the

battery compartment (Fig. 6). When the batteries have been

removed, the thermostat preserves all settings in the memory.

Always use alkaline batteries 2 x1,5 V type AA!

After replacement of the batteries, perform the TEST (see page 6)!

Recommendation: check the batteries before every heating season!

Dispose of old batteries in conformity with regulations on hazardous waste handling!

TRANSMITTER DECRIPTION

TRANSMITTER INSTALLATION

The transmitter must be located as far as possible from interference sources (TV, PC, etc.) and

must not be placed on a metal base. When locating it, pay attention to the thermal properties of the

given place.

- Lift off the back cover of the transmitter acc. to Fig. 5.

- Insert batteries (alkaline 2×1.5 V, type AA); the transmitter will be fully functional (batteries are not

included in the delivery).

- Snap on the back cover again.

- The transmitter is freely portable and can be located, for example, on the table. We recommend using

of the stand included in the delivery.

- If the thermostat is mounted on the wall, pay attention that no heavy-current power lines are led in its

vicinity!

DISPLAY AND CONTROL ELEMENTS DECRIPTION

Fig.4 Fig.5 Fig.6

Fce

: used for function selection

: selection of required temp. (in MANU)

: conﬁ rmation button (ENTER)

information on current temperature

(tE:A), time (CL:O), sum of operating

hours (SU:MA) and day (dE:n)

: for movement in the menu and

temperature setting

1) Preset temperature program indication

2) Selected function – AUTO, MANU, PROG, etc.

3) Anti-freeze temperature (3 °C)

4) Temperature indication – comfortable ,

economical .

5) Required temperature display

Product specificaties

Merk:	Elektrobock
Categorie:	Thermostaat
Model:	BT102

Heb je hulp nodig?

Als je hulp nodig hebt met Elektrobock BT102 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Thermostaat Elektrobock

Elektrobock BT730 Handleiding

12 Maart 2024

Elektrobock PT 32 GST Handleiding

11 September 2023

Elektrobock BPT 32 Handleiding

11 September 2023

Elektrobock PT 14 Handleiding

11 September 2023

Elektrobock PT 713 EI Handleiding

11 September 2023

Elektrobock PT 713 Handleiding

11 September 2023

Elektrobock BPT 22 Handleiding

11 September 2023

Elektrobock BT710 Handleiding

24 Juni 2023

Elektrobock BT102 Handleiding

6 Juni 2023

Elektrobock PT01 Handleiding

13 Mei 2023

Handleiding Thermostaat

Nieuwste handleidingen voor Thermostaat

Tru Components TCN4S-24R Handleiding

18 December 2024

Tru Components TK4S-14RC Handleiding

18 December 2024

Tru Components TX4S-14R Handleiding

17 December 2024

Warmup 5iE Handleiding

16 December 2024

Warmup +Kit Handleiding

16 December 2024

Nobo Connect SWT-IZW Handleiding

15 December 2024

Nobo Connect SWT-IZB Handleiding

11 December 2024

Hive Thermostat Handleiding

10 December 2024

GENERAL Life HT15S Handleiding

9 December 2024

GENERAL Life HT15 Handleiding

9 December 2024