Elektrobock PT10 Handleiding

Elektrobock Thermostaat PT10

Lees hieronder de 📖 handleiding in het Nederlandse voor Elektrobock PT10 (4 pagina's) in de categorie Thermostaat. Deze handleiding was nuttig voor 82 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

ROOM THERMOSTAT

ELEKTROBOCK CZ s.r.o.

Blanenská 1763

Kuřim 664 34

Tel./fa x: +420 541 230 216

www.elbock.cz

Table for registration of your programs

1 2 3 4

Mon

Tue

Wed

Thu

Fri

Sat

Sun

day progr.

Temperature and time

set

CERTIFICATE OF GUARANTEE

(guarantee period for the product amounts to 2 years)

product No.: date of sale:

stamp of shop:

examined by:

MADE IN CZECH REPUBLIC

Send the controller for guarantee and after-guarantee service to distributor's address.

Specifications

Power supply alkal.batteries 2 x 1,5 V typ AA/R6

Number of adjustable temp. 4 temperature changes for a day

Hysteresis 0,5°C

Minimal programming time 30 minutes

Range of possible temp. 5 to 39°C

Step of temperature setting po 1°C

Minimal step of indication 0,1°C

Measurement accuracy 0,5°C

Output relay, max. 5A/250V AC

PT10 is a digital room thermostat for automatic regulation of heating, offering the possibility to set

4 temperature changes for each day (minimal duration of time interval to be set is 30 minutes).

Further advantages:

MAD E IN CZ ECH REPUBLIC

- different temperature program for each day

- simple control and programming

- possibility to make a short-term change in program

temperature

- easy installation to all types of installation boxes

KU/KP68

- retention of memory contents, when the batteries are

replaced sooner than after approx. 25s

Via digital regulation of temperature towards high

savings of energy

- FOR ALL TYPES OF HEATING

- 4 TEMPERATURE CHANGES IN A DAY

- ANTI-FREEZE TEMPERATURE OF 5°C

Overview of produced types:

Install the thermostat on a suitable place, where its operation would not be influenced by direct flow of hot air from

the heater, by solar radiation and other disturbing influences. Also avoid the installation on outer wall.

Follow the illustrations in the course of installation (Pic.1 to Pic.5):

INSTALLATION OF PT10:

Pic.1

Boiler

connection

Terminals 1 and 2

are interconnected

when the thermostat

is switched on

BOILER

Pic.3

Pic.2

Pic.4 Pic.5

Openings for

mounting screws

(for KU/KP 68)

LOCATION OF BATTERIES AND THEIR REPLACEMENT: Pic.6

a, LOCATION OF BATTERIES (see Pic.6)

The batteries are located inside the front microprocessor part. After batteries insertion, colon must blink

on the LCD display. If some unidentifiable conditions occur, it is necessary to remove the batteries for

approx. 1 minute. Always observe correct polarity!

b, REPLACEMENT OF BATTERIES (serves also as a RESET of processor in undeterminable conditions).

Low battery is indicated by blinking symbol " " on the display. Use solely alkali pencil batteries bAtt

2x1.5 V of AA/R6 type! If the replacement lasts more than 25 s, all saved information will be lost!

in compliance with RoHS

LEAD FREE

The installation of PT10 may be performed only by a person with appropriate

qualification in electrical engineering.

PT10

PT1

PT10

PPb

ROOM THERMOSTAT

PT10

PT1

PT10

TS20

HD13-L

PT712

PT32GST

PT22

"TEST" FUNCTION: inspection of correct connection

By pressing and subsequently , the TEST function is activated.

This function performs switching-on and switching-off of the output contact for several times.

Fce

OPERATING INSTRUCTIONS

DISPLAY DESCRIPTION:

CONTROLS:

Fce : serves for function selection

: selection of set temperatures

i: information button (after pressing in AUTO mode it

displays successively required temperature,

current time/temperature and present day).

button for confirmation (ENTER)

+/- : for function selection and temperature setting

2, indication of selected function AUTO, MANU, PROG etc.

5, indication of time/temperature

4, indication of temperatures, comfort , economic

1, indication of set time and temperature program

3, indication of anti-freeze temperature

“ CLO ” FUNCTION: setting of current day and time

1, Press the button, by pressing select CLO (clock) function and confirm by .

2, The time is displayed and indication of hours is blinking on the display, use buttons to set

required hours and confirm by button. Indication of minutes starts blinking, use

buttons to set required minutes and confirm again by button. The day displays (d:1 repre

sents Monday, d:7 Sunday), use buttons to select current day and again confirm by

button. Press the button for comeback.

“ PAr ” FUNCTION : setting of parameters (constants)

1, Press the button, by pressing buttons select PAr (PARAMETERS) and confirm by .

PAr 1: display of current temperature (t) or time (C)

After displaying of Par1, press and with using of buttons select display option.

for displaying of current room temperature and confirm by button.

Cfor displaying of current time and again confirm by button.

PAr 2: setting of economic ( ) temperature

Press to set Par2, symbol displays. Set the value of economic temperature by

buttons and confirm it by pressing .

PAr 3: setting of comfort ( ) temperature

Press to set PAr3, symbol displays. Set the value of comfort temperature by

buttons and confirm it by pressing . Press the button for comeback.

“ PROG ” FUNCTION: setting the program for automatic mode AUTO

1, Press the button, by pressing buttons select PROG (programming)

and confirm by . The day to be programmed is showed on the display.

2, By pressing select the

days according to the table and

confirm by .

3, Symbol 1:U1 for the setting of the first time interval displays for a short time on the display. By pressing of

buttons set the time of the first change (min. step of 30 min.) and by means of pressing

the button assign economic or comfort temperature to this time. Again confirm by pressing

4, Symbol 1:U2 for the setting of the second time interval displays for a short time on the display. By pressing of

buttons set the time of the second change and by means of pressing the button assign

economic or comfort temperature to this time. Again confirm by pressing .

Use the same procedure for the setting of further time intervals and days.

Up to four time intervals (temperature changes) can be defined for one day.

Note: Last temperature set is maintained up to the first change of temperature of next day.

EXAMPLE:

1, Set 17°C for (Pa:r2)

2, Set 22°C for (Pa:r3)

3, Select programming of whole week d1:7 (Prog)

4, assign the time of 6:00 and temperature to 17:U1

5, assign the time of 09:00 and temperature to 17:U2

6, assign the time of 16:00 17:U3and temperature to

7, assign the time of 21:00 17:U4and temperature to

8, Leave the programming by pressing and select

AUTO function for setting the week program

setting of week program

When the output is switched on, AUTO/MANU is showed on the display, otherwise the symbol blinks.

Note: If you do not push any button in 2 minutes, PT10 returns into set mode. Longer pushing of

buttons speeds up their functions.

"PARTY" FUNCTION: short-term change of temperature in AUTO mode

By simple pressing of buttons in AUTO mode, it is possible to make a short-term change of required

temperature. PT10 will maintain this temperature up to next temperature change as defined in the program.

"OFF" FUNCTION: switching off of the thermostat

Press the button, by pressing of buttons select OF:F function and confirm by button.

In this way, PT10 is permanently switched off. In this mode, symbol OF:F and data on current temperature/time are showed

alternatively on the display. To cancel this function, press button and select different mode with using of buttons.

“ ” FUNCTION: anti-freeze temperature in OFF mode

If in the "OFF" mode, the room temperature drops below 5° C, the thermostat automatically switches on the output and symbol

" " is displayed. In this way, PT10 prevents freezing up of the heating system.

FUNCTIONS OF PT10:

Following functions can be selected by pressing and then buttons:

1. AUTO : the thermostat works according to program as set.

2. MANU : serves for manual setting of temp. ( the selection by or buttons), the

temperature should be constant up to next change.

3. CLO : setting of present day and time.

4. PAr : setting of parameters (constants).

5. PROG : programming mode.

6. OFF : in this mode, PT10 is permanently switched-off (with the exception of the regime “ “ ).

Fce

Fce i

Fce

Fce i

Fce

d:1 Mon

d:2 Thu

d:3 Wed

d:4 Thur

d1:5 Mon to Fri

d6:7 Sat to Sun

d1:7 whole week

d:5 Fri

d:6 Sat

d:7 Sun

TABLE: SELECTION OF DAYS FOR PROGRAMMING

Fce

"LOCK" FUNCTION:

By simultaneous pressing of , and buttons the keyboard is locked (buttons are inactive).

Message LOC (LOCK) is shortly displayed. The function can be cancelled, e.g. the keyboard unblocked by

simultaneous pressing of , and buttons (the buttons are again functioning from now).

child lock (protection against unauthorized handling)

Fce

Product specificaties

Merk:	Elektrobock
Categorie:	Thermostaat
Model:	PT10

Heb je hulp nodig?

Als je hulp nodig hebt met Elektrobock PT10 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Thermostaat Elektrobock

Elektrobock BT730 Handleiding

12 Maart 2024

Elektrobock PT 32 GST Handleiding

11 September 2023

Elektrobock BPT 32 Handleiding

11 September 2023

Elektrobock PT 14 Handleiding

11 September 2023

Elektrobock PT 713 EI Handleiding

11 September 2023

Elektrobock PT 713 Handleiding

11 September 2023

Elektrobock BPT 22 Handleiding

11 September 2023

Elektrobock BT710 Handleiding

24 Juni 2023

Elektrobock BT102 Handleiding

6 Juni 2023

Elektrobock PT01 Handleiding

13 Mei 2023

Handleiding Thermostaat

Nieuwste handleidingen voor Thermostaat

Tru Components TCN4S-24R Handleiding

18 December 2024

Tru Components TK4S-14RC Handleiding

18 December 2024

Tru Components TX4S-14R Handleiding

17 December 2024

Warmup 5iE Handleiding

16 December 2024

Warmup +Kit Handleiding

16 December 2024

Nobo Connect SWT-IZW Handleiding

15 December 2024

Nobo Connect SWT-IZB Handleiding

11 December 2024

Hive Thermostat Handleiding

10 December 2024

GENERAL Life HT15S Handleiding

9 December 2024

GENERAL Life HT15 Handleiding

9 December 2024