Elektrobock BT012 Handleiding

Elektrobock Thermostaat BT012

Lees hieronder de 📖 handleiding in het Nederlandse voor Elektrobock BT012 (3 pagina's) in de categorie Thermostaat. Deze handleiding was nuttig voor 127 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/3

LEAD FREE

in compliance with s RoHS

In case of guarantee

or post-guarantee

service, send the

thermostat to the

distributor’s or manu-

facturer’s address.

CERTIFICATE OF GUARANTEE

(guarantee period for the product amounts to 2 years)

product No.: date of sale:

stamp of shop:

examined by:

MADE IN CZECH REPUBLIC

BT0

BT01

BT012

and a wall-mounted receiver

The great advantage is the two-way communication, quick setting and change of the required

temperature by simply turning the knob on the transmitter. The transmitter is portable, or it can be

installed on the wiring box in the reference room. The receiver is equipped with the code self-

learning system and the E-EPROM memory, which preserves the saved code even at power

failure. The wireless version enables simple and quick installation; therefore, there is no need for

laborious and time-consuming installation of a line between the thermostat and boiler with

penetration through ﬂ oors. The coverage of the set can reach up to 35 m.

• Receiver power supply 230 V/ 50 Hz.

• Receiver with the CODE SELF-LEARNING

system and the E-EPROM memory (saving

the code even at power failure).

• Two-wire connection to the boiler.

• Indication LED for signalization of the

states

- power supply indication

- failure state

- relay closed.

receiver - wall-mounted

transmitter

• Simple control element for temperature

setting – knob.

• Indication of the boiler switching and error

states by means of a red LED.

•Night attenuation – button for quick

selection of the night attenuation

(automatic decline by 3 °C for the 8-hour

period).

• Anti-freeze temperature .

• Optional internal frame of a different colour

can be bought (according to the sampler at

www.elbock.cz) for a perfect harmony in

the interior.

ELEKTROBOCK CZ s.r.o.

Blanenská 1763

Kuřim 664 34

Tel.: +420 541 230 216

EU DECLARATION OF CONFORMITY

Hereby, ELEKTROBOCK CZ s.r.o. declares that

the radio equipment type BT012 is in compliance

with Directive 2014/53/EU. The full text of the EU

declaration of conformity is available at the following

internet address: www.elbock.cz

TECHNICAL PARAMETERS

IMPORTANT INFORMATION

TWO-WAY COMMUNICATION

- Providing for reliable signal transmission

and enabling return information acquisition

www.elbock.cz

Receiver

Power supply 230 V/ 50 Hz

Communication type two-way

Frequency 433.92 MHz

Range 200 m (free area)

25 m (built-up area)

Sensitivity < -952 dBm

Output relay, max. 16 A

Protection IP20

Protection class II

Working temperature 0°C to +40°C

Dimensions 110 x 80 x31 mm

Transmitter

Power supply 2 x1.5V alkaline AA batteries

(are included)

Communication type two-way

Hf power < 10 mW

Frequency 433.92 MHz

Hysteresis 0,4°C

Adjustable temp. range 11 to 29°C

(anti-freeze min. 3°C)

Temperature setting by 1°C (from 11°C)

Measurement accuracy ± 1°C

Protection IP20

Battery life 5 years acc. to the battery type used

Working temperature 0°C to +40°C

If... Cause and solution...

the red LED is ﬂ ashing on the transmitter

3 times in 8 s

Low battery indication

Replace the batteries; see page 3

the red LED is ﬂ ashing on the transmitter

2 times in 8 s

Signal transmission failure between the

transmitter and receiver

Check the connection of the receiver; see

page 2; on the transmitter, push long (for

approx. 3 s) the button to test the

connection (the relay on the receiver must

switch several times).

the green LED is ﬂ ashing on the receiver Empty memory; the transmitter code has not been

learned

Perform the code learning; see page 2

the green LED is permanently lit and the red

one is ﬂ ashing on the receiver

The receiver is in the error state (8 min OFF and 2

min ON)

Check the transmitter and test the connection

the green and red LED are ﬂ ashing alternately

on the receiver

The code-learning mode; the receiver is awaiting the

code

On the receiver, push long (for approx. 3 s)

the button

the both LED is lit on the receiver, but the

relay has not been switched

Output circuit failure

Contact the manufacturer immediately.

RECEIVER INSTALLATION

WIRING DIAGRAM

CODE LEARNING

- Lift off the front cover of the receiver acc. to Fig. 1, 2.

- Fix the receiver to the wall (or directly to the wiring box).

- Switch off the main circuit breaker.

- Connect the receiver to the boiler according to the diagram (on the

boiler, use the terminals for wires of the room thermostat 2).

- Connect the receiver to the mains 230 V / 50 Hz.

- Switch on the main circuit breaker; the green LED lights up on the

receiver; thus the receiver is ready for further setting

Owing to disturbance of the signal reception, install the receiver

(in the interior) as far as possible (no less than 0.5 m) from

big metal objects and outside high-current power lines! We

recommend that the installation be done by a person properly

qualiﬁ ed in electrical engineering!

Use if the receiver memory has been erased – the green diode is ﬂ ashing!

1) Push the receiver’s “FUNCTION BUTTON” for about 1 s; the green and red LEDs start ﬂ ashing

alternately; and the receiver is awaiting the code (“learning mode”).

2) On the transmitter (after insetting batteries, see page 3), push the button for approx. 5s (push it until

the red LED on the transmitter lights up); then a signal is send out to the receiver and the TEST starts

up.

3) The code receipt in the receiver is indicated by simultaneous ﬂ ashing of the green and red LED; thus

the code has been learnt. After the code receipt, the output relay is switched several times to verify

correct function of BT012 (the so-called TEST).

BOILER

230 V/50Hz

TRANSMITTER DECRIPTION

TRANSMITTER INSTALLATION

TRANSMITTER MODES

- Lift off the front cover of the transmitter according to Fig. 5.

- Fix the back cover to the wall (or directly to the wiring box), see Fig. 6.

- Remove the protective paper from the batteries; the transmitter will be fully functional (batteries are

included in the delivery of the BT012 purchased).

- Snap back the front cover onto the back one, see Fig. 8–9.

- When replacing the batteries, heed their correct polarity (Fig. 7).

- The necessity to replace the batteries is indicated by the red LED; it ﬂ ashes 3 times in 8 s.

- Always use alkaline batteries 2 × 1.5 V, type AA! (Do not use rechargeable batteries.)

Note: Dispose of old batteries in conformity with regulations on hazardous waste handling!

Set the

required

temperature,

e.g. to 22 °C.

At 10 pm, push

shortly

(for approx. 1 s)

the button.

The thermostat

automatically

reduces the

required

temperature by

3 °C for the period

of 8 hours from

pushing of the

button.

Temperature setting/change:

- By simply turning the knob, set the required temperature by the scale (± 1 °C from 11 °C).

- SWITCHING ON of the boiler is indicated by the red LED; it ﬂ ashes once per 8 s.

Night attenuation:

It is used to automatically reduce the temperature by 3 °C for the 8-hour period. This cycle is

automatically repeated every day.

- Within the required time, shortly push (for approx. 1 s) the button; the diode ﬂ ashes 4 times;

thus the mode is active.

- If you again shortly push the button during the night attenuation, the starting hour of the night attenuation

changes and a new 8-hour cycle starts to count down.

- By turning the temperature change knob, you can cancel the NIGHT ATTENUATION!

EXAMPLE:

Fig.5

Fig.6

Fig.9Fig.8Fig.7

Indication LED short push (approx. 1s) – night attenuation

long push (approx. 5 s) – TEST (code learning)

control element – knob

for temperature setting

holes for installation

screws

Fig.1 Fig.2

Fig.3

holes for installation

screws

output terminals

power terminals

EXPLANATIONS: LIT UNLIT FLASHING

LED1 LED2 FUNCTION

empty memory, code not learned

code learned

FLASHING ALTERNATELY= code learning mode

FLASHING SIMULTANEOUSLY= code has been learned

SIMULTANEOUS LONG FLASH= code has been ERASED

relay switched

ERROR (if no signal is received from the transmitter

within approx. 6 hours, it switches to the 2-min-ON /

8-min-OFF mode). LED 2 is only ﬂ ashing if

the relay is on, i.e. for 2 minutes.

FUNCTION BUTTON:

SHORT PRESS (about 1.5 s)

- for coding.

LONG PRESS (about 5 s)

- RESET deleting the code

from the memory (the green

and red LEDs ﬂ ash

simultaneously).

Product specificaties

Merk:	Elektrobock
Categorie:	Thermostaat
Model:	BT012

Heb je hulp nodig?

Als je hulp nodig hebt met Elektrobock BT012 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Thermostaat Elektrobock

Elektrobock BT730 Handleiding

12 Maart 2024

Elektrobock PT 32 GST Handleiding

11 September 2023

Elektrobock BPT 32 Handleiding

11 September 2023

Elektrobock PT 14 Handleiding

11 September 2023

Elektrobock PT 713 EI Handleiding

11 September 2023

Elektrobock PT 713 Handleiding

11 September 2023

Elektrobock BPT 22 Handleiding

11 September 2023

Elektrobock BT710 Handleiding

24 Juni 2023

Elektrobock BT102 Handleiding

6 Juni 2023

Elektrobock PT01 Handleiding

13 Mei 2023

Handleiding Thermostaat

Nieuwste handleidingen voor Thermostaat

Techno Line TM 3010 Handleiding

18 November 2024

Ferguson FS1TH Handleiding

17 November 2024

EQ-3 HM-RC-19 Handleiding

16 November 2024

EQ-3 CC-RT-N Handleiding

16 November 2024

Delta Dore TYDOM 1.0 Handleiding

16 November 2024

Delta Dore Tybox 5701 FP Handleiding

16 November 2024

Delta Dore Tybox 33 Handleiding

16 November 2024

Delta Dore Tybox 5702 FP Handleiding

16 November 2024

Delta Dore Tybox 31 Handleiding

16 November 2024

Delta Dore TYBOX 827 W RF Handleiding

16 November 2024