Electro Harmonix Nano Battalion Handleiding
Electro Harmonix
Gitaarversterker
Nano Battalion
Lees hieronder de 📖 handleiding in het Nederlandse voor Electro Harmonix Nano Battalion (4 pagina's) in de categorie Gitaarversterker. Deze handleiding was nuttig voor 27 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/4
NANO BATTALION
BASS PREAMP + OVERDRIVE
Congratulations on your purchase of the Electro-Harmonix Nano
Battalion. The all-analog circuitry of the Nano Battalion provides you
with an amazing variety of bass tones in a sturdy and compact pedal. At
the core of the Nano Battalion’s tone is a versatile MOSFET drive circuit
that can range from a subtle, light overdrive to fully saturated distortion.
A flexible three band equalizer includes a three way EQ Position switch
to select where the EQ falls in the pedal’s signal path.
The Nano Battalion features a normal ¼” input, plus a ¼” output that
can output either a normal, unbalanced signal (with a normal TS cable)
or a balanced signal (with a TRS cable) to go right into a mixing console
or recording interface. The Nano Battalion features buffered bypass and
runs on a standard 9.6VDC center negative supply, drawing 45mA.
- Using the Nano Battalion -
Plug the 9VDC adapter into the jack on the top of the Nano Battalion.
The unit must be powered to pass signal even in bypass. Connect an
instrument cable from your bass into the jack. Insert a normal INPUT
TS instrument cable between the jack and a suitable amplifier, OUTPUT
or insert a TRS cable (or TRS to male XLR cable) between the OUTPUT
jack and a suitable mixing console or recording interface. Click the
BYPASS footswitch to engage the Nano Battalion. The LED lights to
indicate that the unit is active.
WARNING:
Your
Nano Battalion
comes equipped with an Electro
-
Harmonix 9.6DC
-
200BI
power supply (same as used by Boss
®
& Ibanez
®
: 9.6 Volts DC 200mA). The Nano
Battalion requires at 9VDC with a center negative plug. Use of the wrong adapter 45mA
or a plug with the wrong polarity may damage your Nano Battalion and void the warranty.
- Main Control -
BYPASS Footswitch & LED – The LED illuminates when the effect is
engaged. The LED will not light if the Nano Battalion is bypassed. Press
the footswitch to toggle between effect on and buffered bypass mode.
VOL Knob – Sets master output level of the pedal.
BLEND Knob – Sets the ratio between clean signal and distorted signal.
Turn BLEND up for more distorted signal.
DRIVE Knob – Sets the intensity and saturation of the distortion.
TONE Knob – Cuts high frequencies from the distortion as you turn the
knob down.
EQ CONTROLS:
TREBLE Knob – Boost or cut high end. No effect when the knob is at
50%. Boosts/cuts frequencies starting above 1kHz. Maximum boost/cut
about +/-12dB around 5kHz.
BASS Knob – Boost or cut low end. No effect when the knob is at 50%.
Boosts/cuts frequencies starting below 200Hz. Maximum boost/cut
about +/-12dB around 60Hz.
MID Switch – No effect when the switch is in the middle position. In
the upwards position, 9dB boost around 500Hz. In the downwards
position, 9dB cut around 500Hz.
- EQ POS. & Signal Path -
The EQ POS switch determines where the EQ (TREBLE, BASS, and MID
controls) falls in the Nano Battalion’s signal path. In all cases, the TONE
control comes immediately after the distorted signal, and the VOL control
is last in the signal path. There are three EQ POS modes, illustrated on
the next page.
- FCC COMPLIANCE -
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. If the device
is not installed and used in accordance with the instructions, it may
cause harmful interference to radio communications and void the user's
authority to guarantee the equipment.
Note:
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help .
Modifications not expressly approved by the manufacturer could void the
user's authority to operate the equipment under FCC rules.
The CE logo indicates that this product has been tested and shown to conform
with all applicable European Conformity directives.
DIST MODE:
In DIST mode the EQ comes after the distortion signal, having a strong
effect on the sound of the distorted signal. The clean signal is not
affected by the EQ at all.
INPUT MODE:
In INPUT mode the EQ comes first in the signal path, affecting both the
clean signal and the signal fed into the distortion. Boosting frequencies
in this mode can help drive the distortion signal to a more saturated
tone.
DRY MODE:
In DRY mode the EQ affects the clean signal, but doesn’t affect the
distorted signal at all.
Product specificaties
| Merk: | Electro Harmonix |
| Categorie: | Gitaarversterker |
| Model: | Nano Battalion |
Heb je hulp nodig?
Als je hulp nodig hebt met Electro Harmonix Nano Battalion stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Gitaarversterker Electro Harmonix
23 Mei 2023
21 Mei 2023
20 Mei 2023
Handleiding Gitaarversterker
- Gitaarversterker Yamaha
- Gitaarversterker Ampeg
- Gitaarversterker Behringer
- Gitaarversterker Boss
- Gitaarversterker Fender
- Gitaarversterker Hartke
- Gitaarversterker Line 6
- Gitaarversterker Marshall
- Gitaarversterker Peavey
- Gitaarversterker Roland
- Gitaarversterker Orange
- Gitaarversterker Vox
- Gitaarversterker NUX
- Gitaarversterker Harley Benton
- Gitaarversterker ART
- Gitaarversterker Valeton
- Gitaarversterker TC Electronic
- Gitaarversterker Radial Engineering
- Gitaarversterker Mooer
- Gitaarversterker Blackstar
- Gitaarversterker Markbass
- Gitaarversterker SPL
- Gitaarversterker Hughes & Kettner
- Gitaarversterker Laney
- Gitaarversterker Ashdown Engineering
- Gitaarversterker Bugera
- Gitaarversterker Palmer
- Gitaarversterker Empress Effects
- Gitaarversterker Dimavery
- Gitaarversterker Fishman
- Gitaarversterker AER
- Gitaarversterker EBS
- Gitaarversterker Rivera
- Gitaarversterker Suhr
- Gitaarversterker Two Notes
- Gitaarversterker GR Bass
- Gitaarversterker Voodoo Lab
- Gitaarversterker AMT
- Gitaarversterker DACS Audio
- Gitaarversterker DV Mark
- Gitaarversterker Budda
- Gitaarversterker API Audio
Nieuwste handleidingen voor Gitaarversterker
18 December 2024
18 December 2024
18 December 2024
17 December 2024
14 December 2024
9 December 2024
2 December 2024
30 November 2024
30 November 2024
30 November 2024