Electro Harmonix Dirt Road Special Handleiding

Electro Harmonix Gitaarversterker Dirt Road Special

Lees hieronder de 📖 handleiding in het Nederlandse voor Electro Harmonix Dirt Road Special (4 pagina's) in de categorie Gitaarversterker. Deze handleiding was nuttig voor 31 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

DIRT ROAD SPECIAL

Solid State Amplifier

Congratulations on your purchase of the Electro-Harmonix DIRT ROAD SPECIAL.

The EHX DIRT ROAD SPECIAL is a reissue of our vintage 1970s amp with

modern enhancements to both the electronics and mechanical design. We’ve also

added four reverbs from our Holy Grail Max reverb pedal: spring, plate, hall, and

reverse.

The DIRT ROAD SPECIAL offers the advantages of a solid state desig lighter n –

weight, smaller size and improved portability but its classic circuitry delivers a –

natural crunch and overdrive with beautiful grit and grind. And, with 4 watts 0

and one 12 inch speaker, you have the perfect amp for any occasion.

IMPORTANT SAFETY INSTRUCTIONS

 Read and keep these instructions.

 Heed all warnings.

 Follow all instructions.

 Clean only with a dry cloth.

 Connect the amplifier to a mains socket outlet with a protective earthing

connection.

 Do not defeat the safety purpose of the polarized or grounding type plug. If

the provided plug does not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

 Protect the power cord from being walked on or pinched.

 Unplug this amplifier during lightning storms or when unused for long periods

of time.

 Where the mains plug or appliance coupler is used as the disconnect device,

the disconnect device shall remain readily operable.

 Apparatus is not for use in tropical climates.

 Do not install near any heat sources such as radiators, heat registers, stoves,

or other apparatus (including amplifiers) that produce heat.

 No naked flame sources, such as lighted candles, should be placed on the

apparatus.

 WARNING: To reduce the risk of fire or electric shock, do not expose this

apparatus to rain or moisture.

 Do not expose this apparatus to dripping or splashing and ensure that no

object filled with liquids is placed on the equipment Do not use this .

apparatus near water.

 Maintain at least six inches of unobstructed air space behind the unit to allow

for proper ventilation and cooling. Air must be capable of freely moving

around the amplifier.

 This amplifier is capable of producing very high sound pressure levels which

may cause temporary or permanent hearing damage. Use care when

adjusting volume levels during use.

 Do not turn the amplifier on without a loudspeaker.

IMPORTANT SAFETY INSTRUCTIONS (cont.)

 Refer all servicing and maintenance to qualified service personnel including

replacement of fuses and vacuum tubes. Changes and modifications not

expressly approved by EHX can void the warranty.

 Servicing is required when the apparatus has been damaged in any way, such

as power-supply cord or plug is damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus has been exposed to rain or

moisture, does not operate normally, or has been dropp ed.

 DO NOT attempt to remove the amplifier chassis. There are no serviceable

parts.

The lightning flash with arrowhead symbol within an equilateral triangle, is intended to

alert the user to the presence of uninsulated “dangerous voltage” within the product’s

enclosure that may be of sufficient magnitude to constitute a risk of electric shock to

persons.

The exclamation point within an equilateral triangle is intended to alert the user to the

presence of important operation and maintenance (servicing) instructions in the

literature accompanying the product.

GETTING STARTED

FRONT PANEL Controls:

INPUT Jack o input for the amplifier. The input – This ¼” jack is the audi

impedance is 1.5M Ω.

VOLUME Knob Controls the overall loudness and gain of the amplifier. We –

recommend turning down VOLUME prior to applying power. Turn up the

VOLUME knob after the amp has been powered up for at least five seconds.

TONE Knob Alters equency response. Turning this control – the amplifier’s fr

counter-clockwise increases bass and turning it clockwise increases treble.

BITE Knob – Alters the amplifier’s gain level and frequency response.

Turning this control clockwise increases the gain and treble content This .

control is also very interactive with the VOLUME control; changing one

affects the other.

REVERB Knob Controls the volume of the reverb When the reverb –.

footswitch is not connected to the back panel via a ¼” mono instrument

cable, the reverb is always on.

TIME Knob Adjusts the decay time, or reverb length/size, for the SPRING, –

HALL and PLATE reverbs. In REVERSE mode, the TIME knob sets the length

of time between striking a note and the reverb fade-in. While in PLATE

mode, when TIME is set to its maximum position, the reverb decay is over

30 seconds, creating a lush reverb wash with each new note.

Reverb Switch Knob Chooses the reverb mode. From left to right, the –

modes are SPRING, HALL, PLATE, and REVERSE.

REAR PANEL:

AC INLET Plug the power cable into this jack –

FUSE Within the AC inlet jack is the fuse holder To access the fuse, use a –.

small flathead screwdriver to carefully slide the fuse holder out.

100VAC (Japan) ............... 1A / 250V slo-blo 5x20mm fuse

1 VAC (US/Canada) 20 ....... / slo-blo 5x20mm fuse 1A 250V

230VAC (EU/Australia) ...... 50 / slo-blo 5x20mm fuse 0mA 250V

WARNING: The AC voltage rating is marked on the amplifier’s chassis.

Failure to use the appropriate fuse could damage the amplifier.

REVERB FOOTSWITCH This jack is to connect the includ reverb –ed

footswitch via a standard ¼” mono instrument cable, which is also included.

The reverb footswitch allows you to turn the reverb on and off When the .

cable is disconnected from the REVERB FOOTSWITCH jack, the reverb is

always on.

SPEAKER s output jack is for loudspeaker connections only –Thi 8 Ωor 16Ω.

WARNING: Connecting your amp to a speaker cabinet that does not have

the appropriate impedance, or to no cabinet at all, could severely damage

the DIRT ROAD SPECIAL and void your warranty. If you choose to connect

the amplifier to a separate speaker cabinet, be sure to select a cabinet that

can handle the full rated power of 40WRMS.

WARRANTY INFORMATION

Please register online at http://www.ehx.com/product-registration or complete

and return the enclosed warranty card within 10 days of purchase. Electro-

Harmonix will repair or replace, at its discretion, a product that fails to operate

due to defects in materials or workmanship for a period of one year from date of

purchase. This applies only to original purchasers who have bought their product

from an authorized Electro-Harmonix retailer. Repaired or replaced units will then

be warranted for the unexpired portion of the original warranty term.

Product specificaties

Merk:	Electro Harmonix
Categorie:	Gitaarversterker
Model:	Dirt Road Special

Heb je hulp nodig?

Als je hulp nodig hebt met Electro Harmonix Dirt Road Special stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Gitaarversterker Electro Harmonix

Electro Harmonix MIG-50 MKII Handleiding

23 Mei 2023

Electro Harmonix Nano Battalion Handleiding

21 Mei 2023

Electro Harmonix Dirt Road Special Handleiding

20 Mei 2023

Handleiding Gitaarversterker

Nieuwste handleidingen voor Gitaarversterker

API Audio Tranzformer LX Handleiding

20 November 2024

API Audio Tranzformer GT Handleiding

20 November 2024

Orange Terror Bass Handleiding

18 November 2024

Ampeg SVT-410HE Handleiding

18 November 2024

Mooer Liquid Handleiding

16 November 2024

Mooer Envelope Handleiding

16 November 2024

Hartke HD50 Handleiding

16 November 2024

Fender Rumble Studio 40 Handleiding

15 November 2024

Blackstar ID:CORE Stereo 10 V4 Handleiding

20 Oktober 2024

Blackstar CabRig Handleiding

20 Oktober 2024