Eberspacher D4S Handleiding
Lees hieronder de 📖 handleiding in het Nederlandse voor Eberspacher D4S (29 pagina's) in de categorie Verwarming. Deze handleiding was nuttig voor 82 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/29
1
D
S
GB
F
J. Eberspächer
GmbH & Co.
Eberspächerstr. 24
D - 73730 Esslingen
Telefon (zentral)
(0711) 939 - 00
Telefax
(0711) 939 - 0500
www.eberspaecher.com
Eberspächer ®
Subject to change
Technical Description
Mounting Instructions
Engine-independent air heaters AIRTRONIC D2 / AIRTRONIC D4 / AIRTRONIC D4S
for diesel fuel
Order No.
AIRTRONIC
D2 – 12 volt 25 2069 05 00 00
AIRTRONIC
D2 – 12 volt 25 2115 05 00 00
As a complete package
AIRTRONIC
D4 – 12 volt 25 2113 05 00 00
AIRTRONIC
D4S – 12 volt 25 2144 05 00 00
Order No.
AIRTRONIC
D2 – 24 volt 25 2070 05 00 00
AIRTRONIC
D2 – 24 volt 25 2116 05 00 00
As a complete package
AIRTRONIC
D4 – 24 volt 25 2114 05 00 00
AIRTRONIC
D4S – 24 Volt 25 2145 05 00 00
Please note!
The
AIRTRONIC
D2 / D4 / D4S - 24 volt is suitable and certified for installation in
vehicles used to transport dangerous substances according to the regulations in
accordance with GGVS / TRS 003 / ADR / ADR 99 (detailed information is contained
in an information sheet with print no. 25 2069 95 13 50). A special control unit should
be used for heating the cargo compartment / cargo – see page 8.
* Please hand this technical description / mounting instruction
to the customer after installation of the AIRTRONIC.
D2 / D4 / D4S
Visit www.butlertechnik.com for more technical information and downloads.
www.butlertechnik.com
2
D
S
GB
F
Contents Page
Area of use of the
AIRTRONIC ......................
2
Statutory regulations, safety instructions
concerning the installation, important
instructions concerning the installation ......... 3
Scope of supply .............................................. 4, 5
Control elements, optional .............................. 4
Technical data ................................................. 6
Principal dimensions ....................................... 7
Installation, type plate,
installation of the
AIRTRONIC
in a vehicle
used to transport dangerous substances ...... 8
Mounting point ................................................ 9
Permissible mounting positions ...................... 10
Wire harness connection, right or left ............ 10
Area of use of the AIRTRONIC
Taking into consideration their heating capacity, the
stationary and auxiliary heaters ‘
AIRTRONIC
’ are
intended for installation and use in all types of motor
vehicles and their trailers, in construction machines,
machines used in agriculture, in boats, ships and
yachts for the purpose of preheating, clearing of
window panes, heating and keeping warm of driver’s
or working cabs, cargo compartments, ship’s cabins,
passenger or crew transport spaces, engine motors
and aggregates.
The
AIRTRONIC
is suitable for and permitted to be
installed in vehicle spaces used by passengers.
However, it is not permitted to be installed in the
driver’s cab or passenger compartment of coaches
with more than 9 seats.
The ‘statutory regulations’, ‘safety instructions’ and
‘important instructions’ relevant to the installation
and printed below in these mounting instructions,
and which govern the equipment selection, area of
use, installation and operation of the
AIRTRONIC
must be taken into consideration.
Based on its functional purpose, the
AIRTRONIC
is
not permitted to be used for other areas of use apart
from those listed, in particular not for a long-term
continuous operation, e.g. to preheat and heat living
spaces, garages, working huts, week-end homes,
hunting lodges, houseboats or similar as well as not
to heat up or to dry objects or living beings (man or
beast) by directly blowing hot air onto them and / or
blowing hot air into appropriate receptacles.
Page
Fastening ........................................................ 11
Combustion air duct / exhaust gas duct ........ 12, 13
Heating air duct .............................................. 13
Fuel supply ...................................................... 14 – 17
Electrical system ............................................ 17
Sectional drawing ............................................ 18
Function,
heating operation at altitudes ......................... 19
Control and safety devices ............................ 20
Circuit diagram parts list ................................ 21
Circuit diagrams at the end of these instructions
Visit www.butlertechnik.com for more technical information and downloads.
www.butlertechnik.com
3
D
S
GB
F
Safety instructions concerning the
installation and repair of the AIRTRONIC
Danger of burns and injury!
Before commencing any work on the
AIRTRONIC
,
disconnect the vehicle battery.
The
AIRTRONIC
may only be started up if the top
shell and the exhaust hood have been mounted in
accordance with the regulations and if the air duct
on the suction side has been carried out in
accordance with the regulations.
During operation, the top shell may not be opened
and hot parts not be touched.
!
Statutory regulations concerning
the installation of the AIRTRONIC
•For installation in motor vehicles subject to the
Regulations authorizing the Use of Vehicles for
Road Traffic (StVZO), the air heater has been
approved by the German Federal Office for Motor
Traffic in keeping with the ‘General Design
Certification’ (AGB) and the official test symbol is
marked on the type plate of the heater.
AIRTRONIC
D2 S 318
AIRTRONIC
D4 / D4S S 323
•The mounting requirements associated with the
General Design Certification (AGB) and further
statutory regulations have been printed in the
corresponding sections of these mounting
instructions.
•When the air heater is installed in special vehicles,
the regulations governing such vehicles must be
taken into account (e.g. GGVS / TRS 003 / ADR /
ADR 99 for vehicles used to transport dangerous
substances).
•The year in which the air heater was operated for
the first time must be permanently recorded on the
type plate. To this end, 3 different years have been
printed on the corresponding field of the type
plate. The valid year is to be identified by removing
(detaching) those two years which are not applicable.
•Subsequent installation of the heater must be
carried out in conformity with these mounting
instructions and must be examined and certified in
writing by an officially approved vehicle specialist
or inspector or employee (Number 4 of Annex VIII b
to the StVZO) in conformity with § 19 Section
3 StVZO. The effectiveness of the design
certification (ABG) for the heater is dependent
on this.
At the discretion of the vehicle owner, the
certificate can be issued as follows:
–As separate ‘Certificate of Approval’ which must
always be kept in the vehicle. A blank form for
this ‘Certificate of Approval’ is attached at the
end of the operating instructions for the
heater. Neutral certificates of approval available
to the motor vehicle specialist are also permissible.
In both cases, the vehicle manufacturer, vehicle
model and vehicle identification number must be
entered.
–As entry in the vehicle registration document
(assessing authority) and in the vehicle
identification card (licencing authority.)
•For vehicles not subject to the StVZO (e.g. ships),
it is necessary to observe the specific regulations
and mounting instructions applicable to the given
vehicle; these may difffer regionally.
•The heater may only be installed or repaired - in
case of the heater being handed in for repair or
guarantee reasons - by a specialist workshop
approved by the manufacturer (service partner) in
keeping with these mounting instructions and
possible special installation recom-mendations.
•The information sticker ‘Switch off heater before
refuelling’ suppplied with the heater must be
attached in a suitable position on the vehicle
(close to the fuel filler neck).
Important instructions for
the installation and repair
of the AIRTRONIC
When mounting or repairing the heater, only original
accessories and original spare parts may be used.
Changes to the
AIRTRONIC
or to components rele-
vant to the heating, the use of outside parts not
approved by Eberspächer as well as an installation
or operation differing from the statutory, safety and /
or function relevant specifications contained in the
mounting instructions and in the operating
instructions are not permissible: this applies in
particular to the electric wiring (circuit diagrams),
the fuel supply, the combustion air and exhaust
gas duct.
Only the control elements provided and / or
approved by us, either on their own or in a given
combination, may be used to operate the
AIRTRONIC
. The use of other control elements
may lead to malfunctions of the heater / heating
operation.
Non-compliance with the statutory, safety and / or
function relevant specifications leads to the lapse
of the General Design Certification (ABG) of the
AIRTRONIC
and to the exclusion of guarantee and
liability on the part of the company J. Eberspächer
GmbH & Co.
Please note!
Further ‘Safety instructions concerning the
installation and repair of the
AIRTRONIC
’ as well as
‘Important instructions concerning the installation’
have been printed directly in the corresponding
sections of these mounting instructions.
ATTENTION !
•In conformity with StVZO, the heat exchanger must
be replaced by an original replacement heat
exchanger by the manufacturer or an authorised
service partner 10 years after the heater was used
for the first time. The vehicle owner / operator of
the heater is responsible for this exchange to be
carried out. A plate with the installation date of the
replacement heat exchanger and the word ‘original
spare part’ must be mounted on the heater (the
plate is supplied with the replacement heat
exchanger - the date needs to be entered).
Visit www.butlertechnik.com for more technical information and downloads.
www.butlertechnik.com
Product specificaties
Merk: | Eberspacher |
Categorie: | Verwarming |
Model: | D4S |
Heb je hulp nodig?
Als je hulp nodig hebt met Eberspacher D4S stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Verwarming Eberspacher
11 September 2023
11 September 2023
11 September 2023
11 September 2023
11 September 2023
11 September 2023
11 September 2023
11 September 2023
Handleiding Verwarming
- Verwarming Bosch
- Verwarming AEG
- Verwarming Junkers
- Verwarming Nefit
- Verwarming Quigg
- Verwarming Remeha
- Verwarming Vaillant
- Verwarming Alde
- Verwarming Atlantic
- Verwarming BeF Home
- Verwarming Bionaire
- Verwarming Blumfeldt
- Verwarming Brink
- Verwarming Danfoss
- Verwarming Dimplex
- Verwarming DIO
- Verwarming Duronic
- Verwarming Duux
- Verwarming Easymaxx
- Verwarming Etherma
- Verwarming Eurom
- Verwarming FlinQ
- Verwarming Gude
- Verwarming Haceka
- Verwarming Heatstrip
- Verwarming Kompernass
- Verwarming Magma
- Verwarming Mesa Living
- Verwarming Mill
- Verwarming Mio Star
- Verwarming Mocoori
- Verwarming Myson
- Verwarming REMKO
- Verwarming Rowi
- Verwarming Sonnenkonig
- Verwarming Stiebel Eltron
- Verwarming Suntec
- Verwarming Supra
- Verwarming Thermor
- Verwarming Toolland
- Verwarming Trumatic
- Verwarming Vasco
- Verwarming Wallas
- Verwarming Webasto
- Verwarming Zehnder
- Verwarming Jaga
- Verwarming JML
- Verwarming Eldom
- Verwarming Day
- Verwarming Ecron
- Verwarming Kemper
- Verwarming Zymbo
Nieuwste handleidingen voor Verwarming
12 December 2024
Suntec Klimatronic Heat Stream Spa 2000 design LED Handleiding
11 Oktober 2024
10 September 2024
Suntec Klimatronic Heat Supreme 2000 glass panel Handleiding
11 Oktober 2024
10 September 2024
19 September 2024
19 September 2024
19 September 2024
11 Oktober 2024
11 Oktober 2024