DSC PG9949 Handleiding

DSC Remote trigger PG9949

Lees hieronder de 📖 handleiding in het Nederlandse voor DSC PG9949 (14 pagina's) in de categorie Remote trigger. Deze handleiding was nuttig voor 55 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/14

PG9949/PG8949/PG4949

PowerG 2-Button Wireless Key Installation

Instructions

WARNING!

Choking Hazard; Small parts; The pendant and belt

clip are NOT for children under 3 years

Do not submerge the wireless key in any liquid as it

will damage the electronic circuits. Keep this manual for future

reference.

Operation

The PGx949 is a programmable 2-button wireless key. The

PGx949 can be configured to transmit up to three separate com-

mands to the alarm system. Two of the commands are transmit-

ted by pressing one of the buttons separately, and the third is by

pressing them simultaneously. Confirmation of a successful

transmission is indicated by the LED light.

Default Settings

Arm {button 1) - Press for 1 second

Disarm (button 3) - Press for 1 second.

Panic (button 4) - Press and hold both buttons for more than 3

seconds.

Device Setup

Enrollment

To quick enroll:

1. On a keypad press [*] [8] [Installer Code]

[804] [000].

2. Press and hold the [ ] button on the wire-

less key until the LED lights steady and then release the

[ ] button while the LED is still lit and a confirmation

message appears on the keypad.

3. Press [*] on the keypad to confirm the device ID.

4. Enter [3 digit wireless key #]

5. Assign the wireless key to a partition by entering the [three

digit partition #].

6. To assign the wireless key to a user enter the [3 digit user #].

To pre-enroll:

1. Remotely configure the unique ID number into the system.

For more information see the HSM2HOST manual.

2. When on-site, press the button on the wireless key.

Programming Buttons

The buttons are programmable.

To change button programming:

1. From a keypad enter [*] [8] [Installer Code] [804][601] to

[632].

2. Configure button 1 (default arm) using the table below.

Enter the desired two digit option.

3. Configure button 3 (default disarm) by entering the desired

two digit option.

4. Configure button 4 (both buttons pressed simultaneously) by

entering the desired two digit option.

Configuration

To enter the wireless configuration section enter [804][601].

Device Toggles

Assembly

Attaching to a Belt Clip

1. Slide the device into the holder until you feel it snap

securely inside.

2. To attach the belt clip, slide it onto the rails on the rear of the

holder.

Mounting

1. Align the holder on a wall facing up as illustrated.

2. Using two #4 5/8” screws and

appropriate wall anchors, secure

the holder to the wall

3. Slide the device into the holder

until you feel it snap securely

inside.

Maintenance

Warning! Modifications to this wire-

less key not expressly approved by the

party responsible for compliance may

void the user’s authority to operate it.

Replacing the Battery

The required battery is CR2032 Lithium 3V, manufactured by

VARTA or Energizer, purchased from a DSC-approved sup-

plier.

When this wireless key is out of use, remove all batteries and

dispose of them separately. Bring electrical appliances to the

local collecting points for waste electrical and electronic equip-

ment. Batteries are harmful to the environment, please help to

protect the environment from health risks.

Replace the battery at least once every 5 years, or upon observ-

ing that the LED flickers when transmitting.

NOTE: The polarity of the battery must be observed. Improper

handling of lithium batteries may result in heat generation,

explosion or fire, which may lead to personal injuries.

WARNING: Danger of explosion if batteries are installed

incorrectly. Replace only with the same or equivalent type rec-

ommended by the manufacturer. Keep away from small chil-

dren. If batteries are swallowed, promptly see a doctor. Do not

try to recharge these batteries. Disposal of used batteries must

be made in accordance with the waste recovery and recycling

regulations in your area.

1. To replace the battery, insert a coin into the slot on the bot-

tom of the unit and twist it open.

Note: Make sure the elastic pad within the cover remains in

place. Put it back in place if it falls off.

2. Extract the old battery from its holder, and replace it with a

recommended new battery. Ensure that the plus side of the

battery faces up, attaining correct polarity.

3. Test the device by pressing the button. The LED indicator

should light.

4. Reattach the cover securely, verifying that the cover snaps

shut.

Cleaning

The use of abrasives of any kind and solvents such as ker-

osene, acetone or thinner is strictly forbidden.

Clean the wireless key only with a soft cloth or sponge moist-

ened lightly with a mixture of water and mild detergent, and

wipe it dry immediately.

Testing

Always test the system at least once per a year.

1. Ensure the device is enrolled in the system.

2. Stand 3 m (10 ft) away from the control panel and press the

button. Verify that the transmit LED lights and the control

panel responds as programmed.

3. Operate the pendant from various locations within the area

covered by the receiver to determine "dead" locations,

where transmission is blocked by walls and large objects, or

affected by structural materials.

Note: If dead/marginal zones are a problem, relocating the

receiver may improve the performance.

Specifications

Frequency Band (MHz): CE Listed PG4949: 433-434MHz;

CE/EN listed PG8949: 868MHz; FCC/IC/UL/ULC listed

PG9949: 912-919MHz

Communication Protocol: PowerG

Battery type: For UL/ULC listed installation use only Varta or

Energizer 3V CR-2032 Lithium battery consumer grade

Battery Life Expectancy: 5 years (not verified by UL/ULC)

Low Battery Threshold: 2.05 V

Note: If transmission is still possible despite the battery condi-

tion, the unit will send a low battery signal to the control panel.

Temperature Range: -10°C to +55°C (UL/ULC only verified

the range 0ºC-49ºC)

Humidity: up to max. 93%RH, non-condensing

Dimensions (LxWxD): 53 x 33 x 11 mm (2.1 x 1.3 x 0.43 in)

Weight: 15 g (0.5 oz)

Weight (including battery): 20 g (0.7 oz)

Note: To be used in non-hazardous locations only.

Compatible Receivers

433MHz Band: HSM2HOST4; HS2LCDRF(P)4;HS2IC-

NRF(P)4; PG4920

868MHz Band: HSM2HOST8; HS2LCDRF(P)8; HS2IC-

NRF(P)8;PG8920

912-919MHz Band: HSM2HOST9; HS2LCDRF(P)9; HS2IC-

NRF(P)9; PG9920

Note: Only devices operating in band 912-919MHz are UL/

ULC listed.

UL/ULC Notes

Only model PG9949 operating in the frequency band 912-

919MHz is UL/ULC listed. The PG9949 has been listed by UL

for commercial and residential burglary applications and by

ULC for residential burglary applications in accordance with

the requirements in the Standards UL1610/UL1023/ULC-

ORD-C1023 and ANSI/SIA CP-01-2010 Control Panel

Standard – Features for False Alarm Reduction.

Note: For UL commercial burglary applications:

• After arming the system via the wireless key the user should verify the

closing confirmation has been indicated at the keypad.

• Panic button must be disabled.

For UL/ULC installations use these device only in conjunction

with compatible DSC wireless receivers: HSM2HOST9,

HS2LCDRF(P)9, HS2ICNRF(P)9 and PG9920. After

installation verify the product functionality in conjunction with

the compatible receiver used.

Europe: The PG4949 and PG8949 are compliant

with the RTTE requirements - Directive 1999/5/EC

of the European Parliament and of the Council of 9

March 1999. The PG8949 is certified by Applica

Test and Certification to the following standards: EN50131-3,

EN50131-1 GRADE 2, CLASS II, EN50131-6 Type C.

Applica Test and Certification has certified only the 868 MHz

variant of this product. According to EN 50131-1:2006 and

A1:2009, this equipment can be applied in installed systems up

to and including Security Grade 2, Environmental Class II. UK:

The PG8949 is suitable for use in systems installed to conform

to PD6662:2010 at Grade 2 and environmental class 2 BS8243.

The Power G peripheral devices have two- way communication

functionality, providing additional benefits as described in the

technical brochure. This functionality has not been tested to

comply with the respective technical requirements and should

therefore be considered outside the scope of the product’s certi-

fication

FCC COMPLIANCE STATEMENT

WARNING! Changes or modifications to this unit not

expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

This device has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protec-

tion against harmful interference in residential installations.

This equipment generates uses and can radiate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio and tele-

vision reception.

However, there is no guarantee that interference will not occur

in a particular installation. If this device does cause such inter-

ference, which can be verified by turning the device off and on,

the user is encouraged to eliminate the interference by one or

more of the following measures:

– Re-orient or re-locate the receiving antenna.

– Increase the distance between the device and the receiver.

– Connect the device to an outlet on a circuit different from the

one that supplies power to the receiver.

– Consult the dealer or an experienced radio/TV technician.

This equipment complies with FCC and IC RF radiation expo-

sure limits set forth for an uncontrolled environment.

This device complies with FCC Rules Part 15 and with Industry

Canada licence-exempt RSS standard(s). Operation is subject

to the following two conditions: (1) This device may not cause

harmful interference, and (2) this device must accept any inter-

ference that may be received or that may cause undesired oper-

ation.

Le present appareil est conforme aux CNR d'Industrie Canada

applicables aux appareils radio exempts de licence. L'exploita-

tion est autorisee aux deux conditions suivantes :(1) l'appareil

ne doit pas produire de brouillage, et (2) l'utilisateur de l'appar-

eil doit accepter tout brouillage radioelectrique subi, meme si le

brouillage est susceptible d'en compromettre le fonctionne-

ment.

PG9949/PG8949/PG4949

Instructions d'installation de la clé sans fil

à 2 boutons PowerG

AVERTISSEMENT !

Risque d'électrocution ; Pièces de faibles dimen-

sions ; La clé sans fil et l'attache de ceinture NE

conviennent PAS à des enfants de moins de 3 ans.

Ne pas plonger la clé sans fil dans aucun liquide car les circuits

électroniques risquent de s'endommager. Conserver ce manuel

pour une consultation future.

Fonctionnement

La clé PGx949 est une clé sans fil à 2 boutons programmables.

Elle est configurable pour transmettre jusqu'à trois commandes

séparées au système d'alarme. Deux des commandes sont trans-

mises en appuyant séparément sur l'un des boutons, et la

troisième est transmise en y appuyant simultanément. La con-

firmation d'une transmission établie avec succès est signalée

par le voyant lumineux.

Réglages par défaut

Armement (bouton 1) : Appuyez sur pendant 1 sec-

onde

Désarmement (bouton 3) : Appuyez sur pendant 1 sec-

onde

Demande d'aide (bouton 4) : Appuyez de façon prolongée les

deux boutons pendant plus de 3 secondes.

Réglage du dispositif

Attribution

Pour une attribution rapide :

1. Sur un clavier, appuyez sur [*] [8] [Code de

l'installateur] [804] [000].

2. Appuyez et maintenez la touche sur la clé sans fil

jusqu'à ce que la LED s'allume stable et puis relâchez le bou-

ton [ ] pendant que le voyant est toujours allumé et un

message de confirmation apparaît sur le clavier.

3. Appuyez sur [*] sur le clavier pour confirmer l'ID de l'appa-

reil.

4. Entrez [3 chiffres sans clé #]

5. Attribuez la clé sans fil à une partition en entrant le [trois

chiffres partition #].

6. Pour attribuer la clé sans fil à un utilisateur d'entrer le [3

chiffres utilisateur #].

Pour une attribution préalable :

1. Configurez à distance le numéro ID unique dans le système.

Pour plus d'informations, consultez le manuel HSM2HOST.

2. Sur site, appuyez sur le bouton [*] de la clé sans fil.

Boutons de programmation

Les boutons sont programmables.

Pour changer la programmation des boutons :

1. Depuis le pavé numérique, entrez la commande [*] [8]

[Code de l'installateur] [804][601] à [632].

2. Configurez le bouton 1 (armement par défaut) en utilisant le

tableau ci-dessous. Entrez l'option à deux chiffres souhaitée.

3. Configurez le bouton 3 (désarmement par défaut) en entrant

les deux chiffres de l'option souhaitée.

4. Configurez le bouton 4 (les deux boutons appuyés simul-

tanément) en entrant les deux chiffres de l'option souhaitée.

Configuration

Pour accéder à la section de configuration sans fil, entrez la

commande [804][601].

Commutateurs du dispositif

Assemblage

Fixation de l'attache de ceinture

1. Faites glisser le dispositif dans l'étui jusqu'à ce qu'il

s'enclenche solidement à l'intérieur.

2. Pour fixer l'attache de ceinture, faites-la glisser dans les rails

sur l'arrière de l'étui.

Fixation

1. Alignez le support sur le mur, vers le haut comme illustré.

00 Disabled 16 Quick Exit

01 Disarm 17 Arm Interior

02 Instant Stay Arm 21 Comm. Output 1

03 Stay Arm 22 Comm. Output 2

04 Away Arm 23 Comm. Output 3

05 [*][9] No Entry 24 Comm. Output 4

06 Chime On/Off 29 Bypass Group Recall

07 System Test 33 Bypass Recall

09 Night Arm 51 Aux. Alarm

12 Global Stay Arm 52 Panic

13 Global Away Arm

14 Global Disarm

[011][01] Supervision - Default [N]

Enables supervision of the device.

00 Désactivé 16 Sortie rapide

01 Désarmer 17 Armement en intérieur

02 Armer en mode à

domicile à effet

instantané

21 Communication Sortie 1

03 Armer en mode à

domicile

22 Communication Sortie 2

04 Armer en mode

d'absence

23 Communication Sortie 3

05 [*][9] Sans entrée 24 Communication Sortie 4

06 Carillon Activé/

Désactivé

29 Rappel de groupe de

suspension

07 Essai du système 33 Rappel de suspension

09 Armer en mode nuit 51 Alarme Alarme

12 Armer globalement en

mode à domicile

52 De demande d'aide

13 Armer globalement en

mode absence

14 Désarmer globalement

[011][01] Supervision : Valeur par défaut [O]

Active la supervision

D-305049

2. En utilisant deux vis #4 5/8" et des

chevilles adéquates, installez le

support au mur

3. Faites glisser le dispositif dans

l'étui jusqu'à ce qu'il s'enclenche

solidement à l'intérieur.

Maintenance

Avertissement ! Des modifications

apportées à cette clé sans fil, qui n'ont

pas été expressément approuvées par

la partie responsable de la conformité, peuvent annuler le droit

de l'utilisateur de la faire fonctionner.

Remplacement de la pile

La pile nécessaire est une pile CR2032 au lithium de 3 V, fabri-

quée par VARTA ou Energizer, achetée auprès d'un fournisseur

agréé DSC.

Quand la clé sans fil est hors d'usage, retirez toutes les piles et

jetez-les au rebut séparément. Amenez les appareils électriques

aux points de collecte de traitement des équipements électro-

niques et électriques usagés. Les piles sont dangereuses pour

l'environnement, veuillez contribuer à protéger l'environnement

pour prévenir des risques sur la santé.

Remplacez la pile au moins une fois tous les 5 ans ou en

fonction de la faiblesse des voyants lumineux lors de la trans-

mission.

REMARQUE : Respectez la polarité de la pile. La manipula-

tion incorrecte des piles au lithium peut engendrer une produc-

tion de chaleur, une explosion ou un incendie, qui peuvent

provoquer des blessures personnelles.

AVERTISSEMENT : Danger d'explosion si les piles sont

installées de façon incorrecte. Remplacez uniquement les piles

par des piles identiques ou équivalentes, recommandées par le

fabricant. Gardez-les hors de portée des enfants en bas âge. Si

les piles sont avalées, consultez immédiatement un médecin.

N'essayez pas de recharger ces piles. L'élimination des piles

usagées doit être réalisée conformément aux réglementations

du recyclage et de la récupération des déchets en vigueur dans

votre région.

1. Pour remplacer la pile, insérez une pièce de monnaie dans la

fente au bas de l'unité et tournez pour ouvrir.

Remarque : Assurez-vous que le joint élastique du cache reste

en place. Remettez-le en place s'il s'échappe.

2. Retirez la pile usagée de son logement, et remplacez-la avec

une pile neuve de type recommandé. Vérifiez que le côté

positif de la pile est orienté vers le haut, préservant la bonne

polarité.

3. Essayez le dispositif en appuyant sur le bouton. L'indicateur

lumineux doit s'allumer.

4. Remontez solidement le couvercle en vérifiant qu'il

s'enclenche.

Nettoyage

L'utilisation de produits abrasifs ou de solvants comme

du kérosène, de l'acétone ou des diluants est strictement

interdite.

Nettoyez uniquement la clé sans fil avec un chiffon doux ou

une éponge légèrement humide avec une solution d'eau et de

détergent doux puis séchez immédiatement.

Test de fonctionnement

Testez toujours le système au moins une fois par an.

1. Vérifiez que le dispositif est attribué dans le système.

2. Tenez-vous à 3 m (10 pieds) de la centrale et appuyez sur le

bouton. Vérifiez que le voyant lumineux de transmission

s'allume et que la centrale répond selon la programmation.

3. Agissez sur le boîtier de commande depuis différents

endroits dans la zone couverte par le récepteur pour déter-

miner les points « morts », où la transmission est bloquée

par les murs et les objets encombrants, ou altérée par les

matériaux structuraux.

Remarque : Si des zones mortes/en marge constituent un prob-

lème, le déplacement du récepteur peut améliorer les perfor-

mances.

Caractéristiques techniques

Plage de fréquences (Mhz) : PG4949 homologué CE : 433-

434 MHz ; PG8949 homologué CE/EN : 868 MHz ; PG9949

homologué FCC/IC/UL/ULC : 912-919 MHz

Protocole de communication : PowerG

Type de pile : Pour les installations référencées UL/ULC, utili-

sez uniquement une pile CR-2032 au lithium de 3 V, Varta ou

Energizer, de qualité grand public

Durée de vie estimée de la pile : 5 ans (non vérifiés par les

organismes UL/ULC)

Seuil de niveau faible de pile : 2,05 V

Remarque : Si la transmission est toujours possible malgré

l'usure de la pile, l'unité enverra un signal de niveau faible de

pile à la centrale.

Plage de température : de -10 °C à +55 °C (UL/ULC a

uniquement vérifié la plage est de 0 °C à 49 °C)

Humidité : Jusqu'à 93 % max., sans condensation

Dimensions (L x l x P) : 53 x 33 x 11 mm (2,1 x 1,3 x 0,43

pouces)

Poids : 15 g (0,5 oz)

Poids (pile incluse) : 20 g (0,7 oz)

Remarque : À utiliser uniquement dans des zones non dan-

gereuses.

Récepteurs compatibles

Bande de 433 MHz : HSM2HOST4; HS2LCDRF(P)4; HS2IC-

NRF(P)4; PG4920

Bande de 868MHz : HSM2HOST8; HS2LCDRF(P)8; HS2IC-

NRF(P)8; PG8920

Bande de 912-919 MHz : HSM2HOST9; HS2LCDRF(P)9;

HS2ICNRF(P)9; PG9920

Remarque : Seuls les dispositifs fonctionnant dans la bande

912-919 MHz sont référencés UL/ULC.

Remarques UL/ULC

Seul le modèle PG9949 fonctionnant dans la bande de

fréquences 912-919 MHz est homologué UL/ULC. Le PG9949

est homologué UL les applications commerciales et

résidentielles anti-intrusion et homologué ULC pour les

applications résidentielles anti-intrusion conformément à la

réglementation des normes UL1610/UL1023/ULC-ORD-

C1023 et ANSI / SIA standard du panneau CP-01-2010

configuration - Caractéristiques de prévention des fausses

alarmes.

Remarque: Pour les applications UL de cambriolage

commercial:

• Après l'armement du système via la clé sans fil, l'utilisa-

teur doit vérifier la confirmation de la clôture a été

indiqué sur le clavier.

• Bouton de panique doit être désactivée.

Pour les installations UL/ULC, utilisez uniquement ces

dispositifs en association avec des récepteurs sans fil DSC

compatibles : HSM2HOST9, HS2LCDRF(P)9,

HS2ICNRF(P)9 et PG9920. Après installation, vérifiez les

fonctionnalités du produit en association avec le du récepteur

compatible utilisé.

Europe : Le PG4949 et le PG8949 respectent la

réglementation RTTE : directive 1995/5/EC du Par-

lement Européen et du Conseil du 9 mars 1999. Le

PG8949 est certifié par Applica Test and Certifica-

tion pour les normes suivantes : EN50131-3, EN50131-1

GRADE 2, CLASSE II, EN50131-6 Type C. Applica Test and

Certification a certifié uniquement la variante à 868 MHz de ce

produit. Selon les normes EN 50131-1:2006 et A1:2009, cet

équipement peut être intégré dans les systèmes installés jusqu'à

et y compris la classe environnementale II, niveau de sécurité 2.

Royaume-Uni : Le PG8949 convient pour l'utilisation dans les

systèmes installés pour se conformer à la norme PD6662:2010

à la classe environnementale 2 et de niveau 2 BS8243. Les dis-

positifs périphériques Power G sont dotés d'une fonction de

communication bidirectionnelle, offrant des avantages supplé-

mentaires comme décrit dans la brochure technique. Cette

fonction n'a pas été déclarée conforme aux besoins techniques

respectifs et doit, par conséquent, être exclue de la certification

du produit.

PG9949/PG8949/PG4949

Instrucciones de instalación de la llave

inalámbrica PowerG de

2 botones

¡ADVERTENCIA!

Peligro de atragantamiento; piezas pequeñas; el

control tipo colgante y el clip para cinturón NO son

para niños menores de 3 años.

No sumerja el teclado inalámbrico en ningún líquido pues

dañará los circuitos electrónicos. Conserve este manual para

referencia futura.

Operación

El modelo PGx949 es una llave inalámbrica programable de 2

botones. Puede configurarse para transmitir hasta tres coman-

dos separados al sistema de alarma. Dos de los comandos se

transmiten al pulsar uno de los botones por separado, y el

tercero al pulsar los botones simultáneamente. La confirmación

de una transmisión correcta se indica mediante la luz LED.

Ajustes predeterminados

Armar (botón 1) - Pulse durante 1 segundo

Desarmar (botón 3) - Pulse durante 1 segundo

Pánico (botón 4)- Pulse mantenga pulsados ambos botones

durante más de 3 segundos.

Configuración del dispositivo

Asociación

Para asociar rápidamente:

1. En un teclado, presione [*] [8] [Código del

Instalador] [804] [000].

2. Mantenga pulsado el botón en el teclado

inalámbrico hasta que el LED se ilumina constante y luego

suelte el botón [ ], mientras que el LED sigue encendido

y un mensaje de confirmación aparece en el teclado.

3. Pulse [*] en el teclado para confirmar el ID del dispositivo.

4. Ingresa [3 dígitos inalámbrica tecla #]

5. Asigne la tecla de conexión inalámbrica a una partición

introduciendo el [tres dígitos partición #].

6. Para asignar la tecla de conexión inalámbrica a un usuario

entrar en el [3 dígitos usuario #].

Para realizar una asociación previa:

1. Configure de forma remota el número de ID único en el

sistema. Si desea más información, consulte el manual del

HSM2HOST.

2. Cuando se encuentre en el lugar, pulse el botón [*] en la

llave a distancia.

Botones de programación

Los botones son programables.

Para cambiar la programación del botón:

1. Desde un teclado numérico ingrese [*] [8] [Código del insta-

lador] [804][601] hasta [632].

2. Configure el botón 1 (armado predeterminado) utilizando la

tabla siguiente. Ingrese la opción de dos dígitos deseada.

3. Configure el botón 3 (desarmado predeterminado) ingre-

sando la opción de dos dígitos deseada.

4. Configure el botón 4 (ambos botones pulsados simultánea-

mente) ingresando la opción de dos dígitos deseada.

Configuración

Para ingresar a la sección de configuración inalámbrica ingrese

[804][601].

Conmutadores de dispositivo

Ensamblaje

Fijación a un clip para cinturón

1. Deslice el dispositivo en el soporte hasta que sienta que

encaja adentro a presión y con seguridad.

2. Para fijar el clip para cinturón, deslícelo en los rieles en la

parte posterior del soporte.

Montaje

1. Alinee el soporte sobre una pared orientado con la cara hacia

arriba como se ilustra.

2. Utilice dos tornillos #4 de 5/8" y

anclajes de pared apropiados para

fijar el receptáculo del dispositivo a

la pared

3. Deslice el dispositivo en el soporte

hasta que sienta que encaja adentro

a presión y con seguridad.

Mantenimiento

¡Advertencia! Las modificaciones a esta llave a distancia no

expresamente aprobadas por la parte responsable de conformi-

dad pueden anular la autoridad del usuario para operarla.

Reemplazo de la batería

La batería requerida es CR2032, de litio, 3 V, fabricada por

VARTA o Energizer, adquirida de un proveedor aprobado de

DSC.

Cuando este llavero a distancia p2-ya no se utilice, retire las bat-

erías y deséchelas por separado. Lleve los dispositivos eléctri-

cos a los puntos de acopio locales para desecho de equipos

eléctricos y electrónicos. Las baterías son dañinas para el ambi-

ente. Ayúdenos a proteger el ambiente contra riesgos para la

salud.

Reemplace la batería por lo menos una vez que cada 5 años, o

cuando observe que el LED parpadea durante la transmisión.

NOTA: Debe observar la polaridad de la batería. La manipu-

lación incorrecta de las baterías de litio puede producir gener-

ación de calor, explosión o incendio, lo que podría causar daños

personales.

ADVERTENCIA: Hay peligro de explosión si las baterías se

instalan incorrectamente. Reemplace las baterías solamente por

el mismo tipo o equivalente recomendado por el fabricante.

Manténgalas alejadas de niños pequeños. Si las baterías son

ingeridas, consulte inmediatamente a un doctor. No intente

recargar estas baterías. El desecho de las baterías usadas debe

realizarse de acuerdo con las reglamentaciones de recuperación

y reciclaje de su área.

1. Para reemplazar la batería, inserte una moneda en la ranura

en la parte inferior de la unidad y gírela hasta abrirla.

Nota: Asegúrese de que la almohadilla elástica dentro de la

cubierta permanezca en su lugar. Colóquela en su lugar si se

cae.

2. Retire la batería vieja de su soporte y reemplácela por una

batería nueva recomendada. Asegúrese de que el extremo

positivo (+) de la batería está hacia arriba para obtener la

polaridad correcta.

3. Pruebe el dispositivo presionando el botón. El indicador

LED debe encenderse.

4. Reinstale la cubierta de manera que quede bien sujetada y

verifique que se cierra a presión.

Limpieza

Se prohíbe terminantemente el uso de abrasivos de

cualquier clase y de solventes tales como queroseno,

acetona o diluyente.

Limpie la llave a distancia solo con un paño suave o una

esponja humedecidos ligeramente con una mezcla de agua y

detergente suave, y séquela de inmediato.

Pruebas

Siempre pruebe el sistema por lo menos una vez al año.

1. Asegúrese de que el dispositivo esté asociado en el sistema.

2. Manténgase a 3 m (10 pies) de distancia del panel de control

y pulse el botón. Verifique que el LED de transmisión se

encienda y el panel de control responda según lo pro-

gramado.

3. Opere el control tipo colgante desde varios lugares dentro

del área cubierta por el receptor para determinar ubicaciones

"muertas", en donde la transmisión está bloqueada por pare-

des y objetos grandes, o afectada por materiales estructura-

les.

Nota: Si las zonas muertas/marginales son un problema, la reu-

bicación del receptor podría mejorar el desempeño.

Especificaciones

Banda de frecuencia (MHz): PG4949 homologado por CE:

433-434 MHz; PG8949 homologado por CE/EN: 868 MHz;

PG9949 homologado por FCC/IC/UL/ULC: 912-919 MHz

Protocolo de comunicación: PowerG

Tipo de batería: Para instalaciones homologadas por UL/ULC

solo use baterías de litio Varta o Energizer, de 3 V CR-2032, de

uso comercial

Vida útil de la batería: 5 años (no verificado por UL/ULC)

Umbral de batería baja: 2,1 V

Nota: Si la transmisión todavía es posible a pesar de la condi-

ción de la batería, la unidad enviará una señal de batería baja al

panel de control.

Rango de temperatura: -10 °C a +55 °C (UL/ULC solo veri-

ficó el rango entre 0 °C y 49 °C)

Humedad: hasta 93% como máximo de humedad relativa, sin

condensación

Dimensiones (Largo x Ancho x Fondo): 53 x 33 x 11 mm (2,1

x 1,3 x 0,43 pulg.)

Peso: 15 g (0,5 oz)

Peso (incluyendo batería): 20 g (0,7 oz)

Nota: Para utilizarse solamente en ubicaciones no peligrosas.

Receptores compatibles

Banda de 433 MHz: HSM2HOST4; HS2LCDRF(P)4;HS2IC-

NRF(P)4; PG4920

Banda de 868 MHz: HSM2HOST8; HS2LCDRF(P)8; HS2IC-

NRF(P)8;PG8920

Banda de 912-919 MHz: HSM2HOST9; HS2LCDRF(P)9;

HS2ICNRF(P)9; PG9920

Nota: Solo los dispositivos que operan en la banda de 912-919

MHz están homologados por UL/ULC.

Notas UL/ULC

Solo el modelo PG9949 que opera en la banda de frecuencia

912-919 MHz está homologado por UL/ULC. El modelo

PG9949 p2-ha sido homologado por UL para aplicaciones

comerciales y residenciales contra robo y por ULC para

aplicaciones residenciales contra robo de acuerdo con los

requisitos indicados en las normas UL1610/UL1023/ULC-

00 Deshabilitado 16 Salida rápida

01 Desarmar 17 Armar zona interior

02 Armar para presencia,

sin retardo

21 Salida de comunic. 1

03 Armar para presencia 22 Salida de comunic. 2

04 Armar para ausencia 23 Salida de comunic. 3

05 [*][9] Sin ingreso 24 Salida de comunic. 4

06 Timbre act./desact. 29 Recordar grupo de salto

07 Prueba del sistema 33 Recordar salto

09 Armar nocturno 51 Alarma auxiliar Alarm

12 Armar presencia

global

52 Pánico

13 Armar ausencia global

14 Desarmar global

[011][01] Supervisión - Predeterminado [S]

Habilita la supervisión.

ORD-C1023 y ANSI / SIA CP-01-2010 Control Panel Standard

- Características para la reducción de falsas alarmas.

Nota: Para aplicaciones de robo comercial UL:

• Después de conectar el sistema a través de la llave

inalámbrica, el usuario debe verificar la confirmación de

cierre se p3-ha indicado en el teclado.

• Botón de pánico debe estar desactivado.

Para instalaciones UL/ULC use estos dispositivos solamente

con receptores inalámbricos DSC compatibles: HSM2HOST9,

HS2LCDRF(P)9, HS2ICNRF(P)9 y PG9920. Después de la

instalación, verifique la funcionalidad del producto junto con el

receptor compatible utilizado.

Europa: Los modelos PG4949 y PG8949 cumplen

con los requisitos de RTTE - Directiva 1999/5/EC

del Parlamento Europeo y del Consejo del 9 de

marzo de 1999. El modelo PG8949 está certificado

por Applica Test and Certification según las siguientes normas:

EN50131-3, EN50131-1 GRADO 2, CLASE II, EN50131-6

Tipo C. Applica Test and Certification p3-ha certificado solamente

la versión de 868 MHz de este producto. De acuerdo con las

normas EN 50131-1:2006 y A1:2009, este equipo puede ser

aplicado en sistemas instalados hasta e incluyendo el Grado 2

de Seguridad, Clase ambiental II. Reino Unido: El modelo

PG8949 es adecuado para uso en sistemas instalados para cum-

plir con PD6662:2010 en el Grado 2 y Clase ambiental 2

BS8243. Los dispositivos periféricos Power G tienen funciona-

lidad de comunicación de dos vías, lo que proporciona ventajas

adicionales como se describen en el folleto técnico. No se ha

probado que estas funciones cumplan con los requisitos técni-

cos correspondientes y, por lo tanto, deberían considerarse

fuera del alcance de la certificación del producto.

PG9949/PG8949/PG4949

Instruções de Instalação do teclado sem fio

Power-G 2 botões

AVISO!

Perigo de asfixia; Partes pequenas; O controle

portátil e o clipe para cinto NÃO são adequados

para crianças menores de 3 anos.

Não submergir a chave sem fio em nenhum líquido,

porque isso danificará os circuitos eletrônicos. Guarde este

manual para consulta no futuro.

Funcionamento

O PGx949 é um teclado sem fio com 2 botões, programável. O

PGx949 pode ser configurado para transmitir até três comandos

separados para o sistema de alarme. Dois dos comandos são

transmitidos pressionando-se um dos botões separadamente, e o

terceiro é transmitido pressionando-os simultaneamente. A

confirmação de uma transmissão com sucesso é indicada pela

luz LED.

Definições Predefinidas

Armar (botão 1) - Pressionar durante 1 segundo

Desarmar (botão 3)- Pressionar durante 1 segundo

Pânico (botão 4)- Pressione e mantenha pressionados ambos os

botões durante mais de 3 segundos.

Configurar Dispositivo

Registro

Para o registro rápido:

1. Em um teclado, pressione [*] [8] [Código do

Instalador] [804] [000].

2. Pressione e segure o botão na chave sem

fio até que o LED acende constante e, em seguida, solte o

botão [ ] enquanto o LED ainda está acesa e uma

mensagem de confirmação é exibida no teclado.

3. Pressione [*] no teclado para confirmar a identificação do

dispositivo.

4. Digite [3 dígitos sem fio chave #]

5. Atribua a chave sem fio a uma partição, digitando o [três

dígitos partição #].

6. Para atribuir a chave sem fio a um usuário entrar no [3

dígitos usuário #].

Para pré-registrar:

1. Configure remotamente o número de ID exclusivo no

sistema. Para mais informação, consulte o manual do

HSM2HOST.

2. Quando no local, pressione o botão [*] no teclado sem fio.

Botões de programação

Os botões são programáveis.

Para alterar o botão de programação:

1. No teclado numérico, insira [*] [8] [Código Instalador]

[804] [601] até [632].

2. Configure o botão 1 (armar predefinido) usando a tabela

abaixo. Insira a opção de dois dígitos desejada.

3. Configure o botão 3 (desarmar predefinido) inserindo a

opção de dois dígitos desejada.

4. Configure o botão 4 (ambos os botões pressionados

simultaneamente) inserindo a opção de dois dígitos

desejada.

Configuração

Para entrar na seção de configuração sem fio, insira [804][601].

Comutações do Disposit

Montagem

Fixar a um Clipe para Cinto

1. Deslize o dispositivo para o suporte até sentir que se encaixa

firmemente no interior.

2. Para fixar o clipe para cinto, deslize-o nas guias na traseira

do suporte.

Montagem

1. Alinhe o suporte em uma parede voltado para a frente, como

mostrado.

2. Usando dois parafusos #4 5/8" e as

âncoras de parede apropriadas, fixe

o suporte à parede

3. Deslize o dispositivo para o suporte

até sentir que se encaixa

firmemente no interior.

Manutenção

Aviso! Quaisquer modificações neste

teclado sem fio não expressamente

aprovadas pela parte responsável pela

conformidade podem anular a autor-

ização do usuário para operar o equipamento.

Substituir a bateria

A bateria necessária é a CR2032 Lítio 3V, fabricada pela

VARTA ou Energizer, comprada em um fornecedor DSC

aprovado.

Sempre que o comando está fora de uso, retire as baterias e eli-

mine-as separadamente. Coloque os aparelhos elétricos nos

pontos de coleta local para equipamento elétrico e eletrônico

usado. As baterias são prejudiciais para o ambiente, ajude a

proteger o ambiente de riscos de saúde.

Substitua a bateria pelo menos a cada 5 anos, ou depois de veri-

ficar que os LED estão piscando quando estão transmitindo.

NOTA: A polaridade da bateria deve ser respeitada. O manuse-

amento inadequado das baterias de lítio pode resultar em ger-

ação de calor, explosão ou incêndio, que pode dar origem a

lesões pessoais.

AVISO: Perigo de explosão se as baterias forem instaladas

incorretamente. Substituir apenas por baterias de tipo equiva-

lente recomendado pelo fabricante. Mantenha afastado das cri-

anças. Se as baterias forem ingeridas, consulte um médico

imediatamente. Não tente recarregar estas baterias. A elimi-

nação das baterias usadas tem de ser feita conforme as regulam-

entações de recuperação e reciclagem de resíduos em sua

região.

1. Para substituir a bateria, insira uma moeda na ranhura na

base da unidade e rode-a para abrir.

Nota: Certifique-se de que a almofada elástica na tampa se

mantém na posição. Se cair, coloque-a de novo na mesma

posição.

2. Retire a bateria antiga e substitua-a com a nova bateria

recomendada. Certifique-se de que o lado positivo da bateria

está voltado para cima, respeitando a polaridade correta.

3. Teste o dispositivo pressionando o botão.

O indicador LED deve ficar aceso.

4. Volte a colocar fixamente a tampa, verificando se fecha.

Limpeza

O uso de abrasivos de qualquer tipo e de solventes como

querosene, acetona ou diluente é estritamente proibido.

Limpe o teclado sem fio apenas com um pano macio ou esponja

umedecida ligeiramente com uma mistura de água e detergente

suave, e seque imediatamente.

Testando

Teste sempre o sistema pelo menos uma vez por ano.

1. Certifique que o dispositivo está registrado no sistema.

2. Permaneça a 3m (10 pés) de distância do painel de controle e

pressione o botão. Verifique se os indicadores LED de

transmissão e o painel de controle respondem como

programado.

3. Opere o controle portátil a partir de várias localizações

dentro da área coberta pelo receptor para determinar

localizações "inativas", onde a transmissão está bloqueada

por paredes e objetos grandes, ou afetada por materiais

estruturais.

Nota: Se zonas inativas/marginais forem um problema, volte a

mudar o receptor para melhorar o desempenho.

Especificações

Faixa de Frequência (MHz): PG4949 com classificação CE:

433-434 MHz; PG8949 com classificação CE/EN: 868 MHz;

PG9949 com classificação FCC/IC/UL/ULC: 912-919MHz

Protocolo de Comunicação: PowerG

Tipo de bateria: Para instalação classificada como UL/ULC,

use apenas bateria de Lítio Varta ou Energizer 3V CR-2032,

tipo consumidor

Duração da bateria: 5 anos (não verificado por UL/ULC)

Limite bateria fraca: 2,05V

Nota: Se a transmissão continuar a ser possível apesar da

condição da bateria, a unidade enviará um sinal de bateria fraca

ao painel de controle.

Limite de temperatura: -10°C a +55°C (UL/ULC apenas ver-

ificou o limite de 0°C - 49°C)

Umidade: até 93%RH no máx., sem condensação

Dimensões (CxLxP): 53 x 33 x 11mm (2,1 x 1,3 x 0,43pol.)

Peso: 15g (0,5oz)

Peso (com bateria): 20g (0,7oz)

Nota: Para ser usado apenas em locais não perigosos.

Receptores Compatíveis

Faixa 433MHz: HSM2HOST4; HS2LCDRF(P)4; HS2IC-

NRF(P)4; PG4920

Faixa 868MHz: HSM2HOST8; HS2LCDRF(P)8; HS2IC-

NRF(P)8; PG8920

Faixa 912-919MHz: HSM2HOST9; HS2LCDRF(P)9; HS2IC-

NRF(P)9; PG9920

Nota: Apenas os dispositivos operando na faixa 912-919MHz

são classificados como UL/ULC.

Notas UL/ULC

Apenas o modelo PG9949 que opera na faixa de frequência

912-919MHz possui classificação UL/ULC. O PG9949 foi

classificado pela UL L para aplicações residenciais e

comerciais de roubo e pela ULC para aplicações residenciais de

roubo, conforme os requisitos das Normas UL1610/UL1023/

ULC-ORD-C1023 e ANSI / SIA CP-01-2010 Painel de

controle padrão - Recursos para diminuição dos falsos alarmes.

Nota: Para aplicações UL roubo comercial:

Depois de armar o sistema através da chave sem fio, o usuário

deve verificar a confirmação do fechamento foi indicado no

teclado.

Botão de pânico deve ser desativado.

Para instalações UL/ULC, use estes dispositivos apenas em

conjunto com receptores sem fio compatíveis com DSC:

HSM2HOST9, HS2LCDRF(P)9, HS2ICNRF(P)9 e PG9920.

Depois da instalação, verifique a funcionalidade do produto em

conjunto com o receptor compatível usado.

Europa: PG4949 e PG8949 estão conforme os req-

uisitos RTTE - Diretiva 1995/5/EC do Parlamento

Europeu e do Conselho de 9 de março 1999. O

PG8949 é certificado pela Applica Test and Certifi-

cation para as seguintes normas: EN50131-3, EN50131-1

GRAU 2, CLASSE II, EN50131-6 Tipo C. A Applica Test and

Certification certificou apenas a variante 868MHz deste pro-

duto. Conforme a EN 50131-1:2006 e A1:2009, este equipa-

mento pode ser aplicado em sistemas instalados até e incluindo

o Grau 2 de Segurança, Classe II Ambiental. RU: O PG8949 é

apropriado para uso em sistemas instalados em conformidade

com PD6662:2010 no Grau 2 e classe ambiental 2 BS8243. O

periférico Power G tem uma funcionalidade de comunicação

em 2 vias, providenciando benefícios adicionais descritos na

brochura técnica. Esta funcionalidade não foi testada para estar

conforme os respectivos requisitos técnicos e deve, portanto,

ser considerada fora do âmbito da certificação do produto.

Limited Warranty

Digital Security Controls warrants that for a period of 12 months from the date of purchase, the product shall be

free of defects in materials and workmanship under normal use and that in fulfillment of any breach of such

warranty, Digital Security Controls shall, at its option, repair or replace the defective equipment upon return of

the equipment to its repair depot. This warranty applies only to defects in parts and workmanship and not to

damage incurred in shipping or handling, or damage due to causes beyond the control of Digital Security

Controls such as lightning, excessive voltage, mechanical shock, water damage, or damage arising out of abuse,

alteration or improper application of the equipment.

The foregoing warranty shall apply only to the original buyer, and is and shall be in lieu of any and all other

warranties, whether expressed or implied and of all other obligations or liabilities on the part of Digital Security

Controls. Digital Security Controls neither assumes responsibility for, nor authorizes any other person

purporting to act on its behalf to modify or to change this warranty, nor to assume for it any other warranty or

liability concerning this product.

In no event shall Digital Security Controls be liable for any direct, indirect or consequential damages, loss of

anticipated profits, loss of time or any other losses incurred by the buyer in connection with the purchase,

installation or operation or failure of this product.

Warning: Digital Security Controls recommends that the entire system be completely tested on a regular

basis. However, despite frequent testing, and due to, but not limited to, criminal tampering or electrical

disruption, it is possible for this product to fail to perform as expected.

Important Information:

Changes or modifications not expressly approved by Digital Security Controls could

void the user’s authority to operate this equipment.

IMPORTANT - READ CAREFULLY: DSC Software purchased with or

without Products and Components is copyrighted and is purchased under

the following license terms:

• This End-User License Agreement (“EULA”) is a legal agreement between You

(the company, individual or entity who acquired the Software and any related Hard-

ware) and Digital Security Controls, a division of Tyco Safety Products Canada Ltd.

(“DSC”), the manufacturer of the integrated security systems and the developer of

the software and any related products or components (“HARDWARE”) which You

acquired.

• If the DSC software product (“SOFTWARE PRODUCT” or “SOFTWARE”) is

intended to be accompanied by HARDWARE, and is NOT accompanied by new

HARDWARE, You may not use, copy or install the SOFTWARE PRODUCT. The

SOFTWARE PRODUCT includes computer software, and may include associated

media, printed materials, and “online” or electronic documentation.

• Any software provided along with the SOFTWARE PRODUCT that is associ-

ated with a separate end-user license agreement is licensed to You under the terms

of that license agreement.

• By installing, copying, downloading, storing, accessing or otherwise using the

SOFTWARE PRODUCT, You agree unconditionally to be bound by the terms of

this EULA, even if this EULA is deemed to be a modification of any previous

arrangement or contract. If You do not agree to the terms of this EULA, DSC is

unwilling to license the SOFTWARE PRODUCT to You, and You have no right to

use it.

LICENSE

The SOFTWARE PRODUCT is protected by copyright laws and international copyright treaties, as well as

other intellectual property laws and treaties. The SOFTWARE PRODUCT is licensed, not sold.

1. GRANT OF LICENSE This EULA grants You the following rights:

(a) Software Installation and Use - For each license You acquire, You may have only one copy of the

SOFTWARE PRODUCT installed.

(b) Storage/Network Use - The SOFTWARE PRODUCT may not be installed, accessed, displayed, run,

shared or used concurrently on or from different computers, including a workstation, terminal or other digital

electronic device (“Device”). In other words, if You have several workstations, You will have to acquire a

license for each workstation where the SOFTWARE will be used.

PRODUCT, but You may only have one copy per license installed at any given

time. You may use the back-up copy solely for archival purposes. Except as

expressly provided in this EULA, You may not otherwise make copies of the

SOFTWARE PRODUCT, including the printed materials accompanying the

SOFTWARE.

2. DESCRIPTION OF OTHER RIGHTS AND LIMITATIONS

(a) Limitations on Reverse Engineering, Decompilation and Disassembly - You

may not reverse engineer, decompile, or disassemble the SOFTWARE PRODUCT,

except and only to the extent that such activity is expressly permitted by applicable

law notwithstanding this limitation. You may not make any changes or

modifications to the Software, without the written permission of an officer of DSC.

You may not remove any proprietary notices, marks or labels from the Software

Product. You shall institute reasonable measures to ensure compliance with the

terms and conditions of this EULA.

(b) Separation of Components - The SOFTWARE PRODUCT is licensed as a single product. Its component

parts may not be separated for use on more than one HARDWARE unit.

SOFTWARE PRODUCT is licensed with the HARDWARE as a single integrated product. In this case, the

SOFTWARE PRODUCT may only be used with the HARDWARE as set forth in this EULA.

(d) Rental - You may not rent, lease or lend the SOFTWARE PRODUCT. You

may not make it available to others or post it on a server or web site.

(e) Software Product Transfer - You may transfer all of Your rights under this EULA only as part of a

permanent sale or transfer of the HARDWARE, provided You retain no copies, You transfer all of the

SOFTWARE PRODUCT (including all component parts, the media and printed materials, any upgrades and

this EULA), and provided the recipient agrees to the terms of this EULA. If the SOFTWARE PRODUCT is an

upgrade, any transfer must also include all prior versions of the SOFTWARE PRODUCT.

(f) Termination - Without prejudice to any other rights, DSC may terminate this EULA if You fail to comply

with the terms and conditions of this EULA. In such event, You must destroy all copies of the SOFTWARE

PRODUCT and all of its component parts.

(g) Trademarks - This EULA does not grant You any rights in connection with any trademarks or service

marks of DSC or its suppliers.

3. COPYRIGHT - All title and intellectual property rights in and to the SOFTWARE PRODUCT (including but

not limited to any images, photographs, and text incorporated into the SOFTWARE PRODUCT), the

accompanying printed materials, and any copies of the SOFTWARE PRODUCT, are owned by DSC or its

suppliers. You may not copy the printed materials accompanying the SOFTWARE PRODUCT. All title and

intellectual property rights in and to the content which may be accessed through use of the SOFTWARE

PRODUCT are the property of the respective content owner and may be protected by applicable copyright or

other intellectual property laws and treaties. This EULA grants You no rights to use such content. All rights not

expressly granted under this EULA are reserved by DSC and its suppliers.

4. EXPORT RESTRICTIONS - You agree that You will not export or re-export the SOFTWARE PRODUCT to

any country, person, or entity subject to Canadian export restrictions.

5. CHOICE OF LAW - This Software License Agreement is governed by the laws of the Province of Ontario,

Canada.

6. ARBITRATION - All disputes arising in connection with this Agreement shall be determined by final and

binding arbitration in accordance with the Arbitration Act, and the parties agree to be bound by the arbitrator’s

decision. The place of arbitration shall be Toronto, Canada, and the language of the arbitration shall be English.

7. LIMITED WARRANTY

(a) NO WARRANTY - DSC PROVIDES THE SOFTWARE “AS IS” WITHOUT WARRANTY. DSC DOES NOT

WARRANT THAT THE SOFTWARE WILL MEET YOUR REQUIREMENTS OR THAT OPERATION OF THE

SOFTWARE WILL BE UNINTERRUPTED OR ERROR-FREE.

(b) CHANGES IN OPERATING ENVIRONMENT - DSC shall not be responsible for problems caused by

changes in the operating characteristics of the HARDWARE, or for problems in the interaction of the

SOFTWARE PRODUCT with non-DSC-SOFTWARE or HARDWARE PRODUCTS.

IF ANY STATUTE IMPLIES WARRANTIES OR CONDITIONS NOT STATED IN THIS LICENSE

AGREEMENT, DSC’S ENTIRE LIABILITY UNDER ANY PROVISION OF THIS LICENSE AGREEMENT

SHALL BE LIMITED TO THE GREATER OF THE AMOUNT ACTUALLY PAID BY YOU TO LICENSE

THE SOFTWARE PRODUCT AND FIVE CANADIAN DOLLARS (CAD$5.00). BECAUSE SOME

JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR

CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATION MAY NOT APPLY TO

YOU.

(d) DISCLAIMER OF WARRANTIES - THIS WARRANTY CONTAINS THE ENTIRE WARRANTY AND

SHALL BE IN LIEU OF ANY AND ALL OTHER WARRANTIES, WHETHER EXPRESSED OR IMPLIED

(INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSE) AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON THE PART OF

DSC. DSC MAKES NO OTHER WARRANTIES. DSC NEITHER ASSUMES NOR AUTHORIZES ANY

OTHER PERSON PURPORTING TO ACT ON ITS BEHALF TO MODIFY OR TO CHANGE THIS

WARRANTY, NOR TO ASSUME FOR IT ANY OTHER WARRANTY OR LIABILITY CONCERNING

THIS SOFTWARE PRODUCT.

00 Desativado 16 Saída Rápida

01 Desarmar 17 Armar Interior

02 Armar Presente

Instantâneo

21 Com. Saída 1

03 Armar Presente 22 Com. Saída 2

04 Armar Ausente 23 Com. Saída 3

05 [*][9] Nenhuma

Entrada

24 Com. Saída 4

06 Campainha

On/Off

29 Desvio Rechamada Grupo

07 Teste Sistema 33 Desvio Rechamada

09 Armar Noturno 51 Aux. Alarme

12 Armar Presente Global 52 Pânico

13 Armar Presente Global

14 Desarmar Global

[001][01] Supervisão - Predefinido [S]

Ativa a supervisão.

Este equipamento opera em caráter secundário, isto é, não

tem direito a proteção contra interferência prejudicial, mesmo

de estações do mesmo tipo, e não pode causar interferência a

sistemas operando em caráter primário.

Product specificaties

Merk:	DSC
Categorie:	Remote trigger
Model:	PG9949
Kleur van het product:	Zwart
Ingebouwd display:	Nee
Gewicht:	32 g
Breedte:	53 mm
Diepte:	33 mm
Hoogte:	11 mm
Merkcompatibiliteit:	DSC
Maximumbereik:	2000 m
Backlight toetsen:	Nee
Input type:	Drukknopen
Bedrijfstemperatuur (T-T):	-10 - 55 °C
Batterijtechnologie:	Lithium
Type batterij:	CR2032
Number of devices supported:	32