Drayton miGenie Wish 3 Handleiding

Drayton Smarth home miGenie Wish 3

Lees hieronder de 📖 handleiding in het Nederlandse voor Drayton miGenie Wish 3 (2 pagina's) in de categorie Smarth home. Deze handleiding was nuttig voor 61 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Step 1: Mounting the Wall-plate

! IMPORTANT:

Installation must only be carried out by a

qualiﬁed electrician or heating engineer.

Make sure mains input has a 3 amp fuse.

! CAUTION! Before installation, make sure the

mains supply is switched off!

Option 1: Fitting a new wall-plate

The ideal location is 1.2m above

ﬂoor level, with reasonable

lighting, good access, no

condensation, no extremes of

temperature and a supporting

surface that fully covers the

back of the unit. Position with

70mm clearance to the right,

25mm above and sufﬁcient room

to access the securing screws

underneath. Fix, with terminals

at the top, either direct to a ﬂat

wall using wall plugs and No. 6 x

1” (25mm) woodscrews, or on a

ﬂush mounting single conduit box

type UA1 (BS4662) using M3.5 x

14 bolts. Check the 3A fuse, and

switch on the mains.

! DO NOT use a surface mounting box

→

Option 2: Using an existing

industry standard wall-plate

Loosen the securing screws

on the old programmer and

unplug it. Check that there is

70mm clearance to the right of

the wall-plate and 25mm above

it. Check the wiring diagram for

your product model to compare

terminals and, if necessary,

change the wiring of the wall-

plate to suit. Now ﬁt the miGenie

controller into the wall-plate and

tighten the securing screws.

Check the 3A fuse, and switch on

the mains.

Wireless Packs

Technical elpline: H 0333 7000 62 2

Website: www.draytoncontrols.co.uk

www.mi-genie.co.uk

E-mail: customer .care@draytoncontrols.co.uk

l @DraytonControls

x /DraytonControls

EU Design Regs:- 002180638-1/2/3

Installer uide 6490211001 ss G 0 I D

INSTALLATION Guide

Single Channel : miGenie Wish 1 T714R

Dual Channel: miGenie Wish 2 T724R

Multi Channel: miGenie Wish 3 T744R

Step 2: Wiring

→

Step 3: continued... Step 4: Signal Strength Step 5: Mounting Options Step 6: Install the miGenie Gateway & miGenie app

→ → → →

The miGenie thermostat(s) & miGenie gateway are

pre-bound to the miGenie controller in the factory so

they just need to be positioned in the best place for

wireless communication. To help with this there is a

built in signal strength indicator, available in the Zone

Settings menu on the miGenie controller, as shown.

It is recommended that the signal strength is Good or

Very Good to ensure communication is maintained.

The signal strength can also be seen on the miGenie

thermostat.

To enter the Signal Strength menu

• Press + & - for approx. 5 secs, then scroll (+/-) to show

10. ADV-SET,

• Press ( ) to enter the Advanced Settings menu,

• Press +/- until 19 WIRELESS is shown,

• Press ( ) to enter the Wireless menu,

• Press +/- to show 21 SIG-LEVEL as shown,

• Press ( ) to see the current signal strength.

miGenie thermostat rear

Battery Covers:

Slide outwards

to remove

Once the best position has been identiﬁed, the

miGenie thermostat should be ﬁxed to the wall using

the wall bracket as shown.

Location & Wiring

The miGenie gateway is designed to be placed

on a ﬂat surface and should be located next to the

customer’s internet router. A short ethernet cable is

provided to connect the miGenie gateway to a spare

LAN port on the back of the internet router (see

image below).

Creating a User Account

Note: You can only create a User Account when your

miGenie Wireless Pack has been fully installed.

You will ﬁrst need to download the Drayton miGenie

app for your smartphone or tablet which is available

from the App Store or Google Play.

The app guides you through the registration process

which connects your miGenie system to your e-mail

address. During this process you will be asked to

press the button on the back of the miGenie gateway

which will ﬂash green until the connection is made.

A veriﬁcation e-mail will be sent to you to conﬁrm

your e-mail address before the app can be used.

Once the gateway has been registered the system

is ready to control your heating and hot water.

To control your miGenie system from additional

smartphones or tablets simply download and install

the app and login using the same e-mail address

and password.

NB. miGenie thermostat can also be positioned using

the table stand included.

The miGenie gateway is powered from a standard

mains wall socket using the supplied adaptor plug.

Care should be taken to mount the miGenie thermostat

in a position which is not subject to direct sunlight or

draughts. Preferably it should be mounted on an inside

wall about 1.2m (4ft) above the ﬂoor in a position where

it can respond to room temperature but away from the

direct inﬂuence of radiators or other appliances giving

off heat.

Status

The miGenie gateway reports status information

on the LED located on the rear of the product.

An overview of the status information is given in the

table below:

Connect the wiring as shown above.

T714R only: Note that the output contacts are

voltage-free, so power needs to be put on to

Terminal 1 either by linking from Terminal L or

from a separate supply with a 3A fuse.

! IMPORTANT:

Always switch off the mains before removing

the miGenie controller and never ﬁt it to a live

wall-plate!

eg. eg.

It has to be placed in a location where it will be able to

control the room temperature.

If POOR is displayed, look for a better location

If NO SIGNAL is displayed, try connecting again with

the room unit in a different position. To exit, press + &

- keys for approx. 5 seconds. If there is no key pressed

for 2 minutes, the menu will be exited automatically.

1.2m

1 2 3

LANWAN

LED State

(During Setup) Activity

Cycling through Red,

Amber, Green

The miGenie gateway is attempting

to bind to a miGenie Controller.

Can be started manually by

pressing and holding the gateway

but ton for 5 seconds.

Off Indicates that either;

- the miGenie gateway is not

connected to the miGenie controller.

- the miGenie gateway has not been

registered with an internet account

and app.

Green ﬂashing every

1 second

This occurs when the button on the

rear of the gateway is pressed. The

miGenie gateway is attempting to

connect to a miGenie app via the

internet. This mode will time out

after 5 minutes.

LED State (During

normal use)

Activity

Green Indicates 'all OK' – the gateway is

connected to the miGenie controller

and internet control is available.

Solid Red No RF signal – the device should

be relocated closer to the miGenie

controller.

Solid Amber No internet connection – check the

status of the local internet router

and all cabling.

Single Channel:

miGenie T714R

Dual Channel:

miGenie T724R

Multi Channel:

miGenie T744R

Ch1 Ch2 Ch3 Ch4

Step 3:

miGenie Thermostats

- Checking the batteries

How do I know when to change

the batteries?

When the batteries start to run low a battery icon

will ﬂash in the display, to indicate “low battery”

during this time the miGenie thermostat will function

normally. Please replace batteries with 2 x 1.5V

IEC LR6 (AA) Alkaline batteries. When the battery

icon alone is shown in the display, the batteries are

completely exhausted and the miGenie thermostat

will cease to function (see below).

Re-activate by replacing the batteries.

Battery Handling

Batteries, rechargeable or not, should not be disposed

of into ordinary household waste. Instead, they must be

recycled properly to protect the environment and cut

down the waste of precious resources.

Your local waste management authority can supply

details concerning the proper disposal of batteries.

In compliance with the EU Directive 2006/66/EC, the

button cell battery located on the printed circuit board

inside the product, can be removed at the end of the

product life, by professional personnel only.

How to replace the batteries

Remove the battery covers as shown. Replace the

spent batteries with 2 x 1.5V IEC LR6 (AA) Alkaline

batteries ensuring correct orientation. Replace the

battery covers pressing fully home.

Drayton

401 Southway Drive

Plymouth

PL6 6QT

United Kingdom

Add and Remove Devices

(NB: only required if adding a new thermostat. All items in the Wish 1, 2 & 3 packs are pre-bound)

To manually connect a miGenie thermostat, insert the batteries into the thermostat and wait for “Bind?” to be

displayed, press ( ) to select. You will also need to enter the binding process on the miGenie Controller, by entering

the Advanced Settings menu, then the Zone settings and select the Device manager option. In this screen select

the Add thermostat option to complete the binding process. To remove a miGenie Thermostat enter the Device

manager option in the miGenie controller using the same sequence detailed above. The option will now display

Remove Thermostat, select this option and the thermostat will be removed from the system.

To manually connect a miGenie gateway, press and hold the button on the rear of the gateway for more than 5

seconds, the LED will repeatedly ﬂash red-yellow-green. You will also need to enter the binding process on the

miGenie Controller, by entering the Advanced Settings menu, then System settings, then Internet options. In this

screen select the Add gateway option to complete the binding process. To remove a miGenie Gateway enter the

Internet options menu in the miGenie controller using the same sequence detailed above. The menu will display

Remove gateway, select this option and the gateway will be removed from the system.

Technical Data

Step 7: Connection Charts

Step 8: Advanced Settings

→

Feature Description Factory Pre-Set

Device manager Add, replace or remove RF room thermostats Pre-bound

Signal strength Displays the signal strength of the selected zone, if a miGenie thermostat is connected to the zone

Channel settings (within

Zone settings)

Customise the application type and associated control settings for zones following this

application type

Application type Selecting the application type pre-conﬁgures

the available zone information

Zone 1: Heating:

Zone 2: Hot Water

Zone 3: Heating

Zone 4: Unused

Control type

*Heating zones only

Select TPI or TP.

TPI = Use if the house usually reaches setpoint in ≤ 1 hour.

TP = Use if the house usually reaches setpoint in ≥ 1 hour.

TPI

Cycle rate (only when

control type is TPI or TP)

Select 3 cph (cycles per hour), 6 cph or 12 cph 6 cph

Frost temperature Disable frost protection or set bet ween 3-10°C 5°C

Valve protection The output will be activated for the speciﬁed time (in minutes). This

will happen weekly, related to the last action of the output. Select 0

to 10 minutes.

0 mins (Off)

Feature Description Factory Pre-Set

Advanced settings ! CAUTION! These settings should only be modiﬁed by a qualiﬁed person. They can inﬂuence the

safety and the proper functioning of the system

System settings These are settings applicable to the system controller unit, global settings

for bound nodes and internet connection settings

Backlight miGenie controller options are:

On with timeout, Always on, Always off

miGenie thermostat options are:

On with timeout, always off

On with timeout

Lock settings Enable or disable the screen lock for the miGenie controller. To lock:

enter a 3 digit code for protection. To unlock: enter the 3 digit code

000

Master code 401

Product Information View product details for devices in the system e.g. part number, ﬁrmware version, etc.

Signal strength Informs about the current signal strength of the products connected to the system

Internet options Sub-menu relating to the connection of an internet gateway – enables

a gateway to be added, replaced or removed with an indication of signal strength.

System reset Will reset all settings to factor y pre-sets

Zone settings Customise each zone according to personal preferences

These are setting which will be applied to a connected thermostat

Select zone Select the zone for the following actions

Rename zone To rename an existing zone Heating, H Water, LivRoom

Edit schedule Update the schedule for the zone

Zone setup Contains detailed zone setup values – see below for descriptions

Minimum

temperature

The minimum set temperature that can be set

for the zone

5°C

Maximum

temperature

The maximum set temperature that can be set

for the zone

30°C

Eco

temperature

Temperature used for energy saving events

e.g. during the night

16°C

Comfort

temperature

Temperature used for comfort events

e.g. during the day

21°C

Offset

temperature

Adjust the displayed temperature to personal needs 0°C

! IMPORTANT:

Always switch off the mains before removing

the miGenie Controller – and never ﬁt it to a live

wall-plate!

→

Arrowed numbers relate to the junction box.

* Consult boiler handbook for details of pump

overrun wiring.

Make the wiring connections, as above, for the

appropriate system. For surface wiring, snap out the

cable entry strip on the bottom edge of the wall-plate.

miGenie controllers are double-insulated and need

no earth connection, but an earthing continuity (loop)

terminal is provided for convenience.

After wiring, clip on the unit and tighten the securing

screws. Check the mains input has a 3A fuse, and switch

on the mains.

Biﬂo system: Model T724R Twinzone system: Model T724R

From the Home screen, select

Settings, then Advanced settings

as shown.

From here you can edit the assigned zones, rename them if required

and check the Signal strength.

→

→→ →

→

miGenie Controller miGenie Controller

3 Zone system: Model T744R

miGenie Controller

Select a name from the list or

select 'Custom zone name' to

create a new zone name.

miGenie controller miGenie thermostat miGenie gateway

Power Supply 230V a.c. +10% -10% 50Hz 2 X 1.5V IEC LR6(AA) alkaline

batteries

5V d.c. 1A USB Micro-B

Switch Rating 2 (1) A 230V a.c. each switch N/A

Wiring Fixed wiring only, to comply with

current IET regulations (BS7671)

No wiring required

Battery life N/A N/A 2 years typical

Ambient Temperature

Operating: 0º to 45ºC (miGenie controller 3 / 4 channel 0º to 40ºC)

Storage: -20ºC to 55ºC

Ambient humidity

(non condensing)

Operating 25% to 90%

Storage 15% to 95%

Temperature Range 5 ºC - 30 ºC N/A

Control Accuracy <0.6ºC at 4º / hour N/A

Timing resolution 1 minute N/A

Temperature resolution 0.5°C N/A

Ball Pressure Test

Temperature

75ºC

Pollution Degree 2

Energy Class IV = 2% (Acc. EU 811/2013, 812/2013, 813/2013, 814/2013) N/A

Soft ware Class A

Without Mains Power Display: blank; Time: always kept

Program times: always preserved

N/A

Rated Impulse Voltage 2.5kV N/A

Radio Frequency 868.3MHz (Bi-directional communication)

Radio Signal Range 30m typically. The range may be affected by the composition / density and the number

of walls bet ween the miGenie products

Mounting Industry standard wall plate Table topWall bracket or table stand

Relevant EC Directives:

20 /14 35/EC Low Voltage Directive

20 4/ 0/EC lectromagnetic mpatibility irective1 3 E Co D

1999/5/EC &TTE rective R Di

2013/56/EU Battery Directive

2011/65/EU RoHS Directive

Applied Standards: EN60730-1; EN60730-2-7; EN60730-2-9

EN 300 220-2; EN 301 489-3

Product specificaties

Merk:	Drayton
Categorie:	Smarth home
Model:	miGenie Wish 3
Kleur van het product:	Wit
Breedte:	148 mm
Diepte:	28 mm
Hoogte:	93 mm
Connectiviteitstechnologie:	Draadloos
Type stroombron:	AC
Accu/Batterij voltage:	1.5 V
Certificering:	2006/95/EC, 2004/108/EC, 1999/5/EC R&TTE, 2013/56/EU, EN60730-1; EN60730-2-7; EN60730-2-9, EN 300 220-2; EN 301 489-3
Interface:	IR Draadloos
Ingangsspanning:	230 V
Temperatuur bij opslag:	-20 - 55 °C
Frequentie:	868.3 MHz
Luchtvochtigheid bij opslag:	15 - 95 procent
Bereik temperatuurmeting:	5 - 30 °C
Maximale afstand:	30 m
Levensduur batterij:	2 jaar
Bedrijfstemperatuur (T-T):	0 - 45 °C
Relatieve vochtigheid in bedrijf (V-V):	25 - 90 procent
Type batterij:	LR6(AA)
Gemeten omgevingsomstandigheden:	Temperatuur