Draper Targa Handleiding

Draper Projectiescherm Targa

Lees hieronder de 📖 handleiding in het Nederlandse voor Draper Targa (4 pagina's) in de categorie Projectiescherm. Deze handleiding was nuttig voor 22 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

Hanging Screen

General:

When locating viewing surface and checking clearance for screen’s operation,

remember surface is centered in case. Handle case carefully to protect its ﬁnish.

Regardless of mounting method, screen should be positively and securely sup-

ported so that vibration or even abusive pulling on the viewing surface will not

cause case to work loose or fall. Installer must insure that fasteners used are of

adequate strength and suitable for the mounting surface chosen.

Suspended Installation:

Suspend screens from holes in endcaps as shown. “S” hooks, chains (or cable)

and turnbuckles should be provided by installer. “S” hooks should go through

the front holes on the endcaps (see drawing on page 3), and both ends of the

“S” hooks should be crimped for additional safety. Chains should be attached to

beams or other structural members. Turnbuckles should be adjusted so screen

hangs level.

Wall Installation:

Mount screen through holes in back of endcaps as shown. Installer should

furnish screws, toggle bolts, molly bolts, nylon or lead anchors as required.

Wall Installation with Optional 6" Extension Brackets:

Mount the brackets (not included with screen—see diagram on page 3) using

hardware recommended for “Wall Installation” (above). Then, suspend the

screen from the front holes with “S” hooks (as in “Suspended”). For added

safety, be sure to

crimp both ends

of the “S” hooks so the screen cannot come

off. For a more rigid installation, mount the screen from the back holes to the

front of the bracket by using the screws and nuts provided with the brackets.

Wall or Ceiling Installation with Optional Floating Brackets:

Floating brackets should be located on studs or joists. The bracket then

attaches at any almost any point along the case. For details, see separate

instruction sheet that ships with the Floating Wall Bracket.

Operation

Before operating screen remove tape securing fabric and dowel to roller. If view-

ing surface hangs out of case 8"-9", tape has probably been broken by rough

handling in shipment, allowing surface to “unwrap” one turn about the roller.

Manually wrap fabric back around the roller without turning the roller itself.

110-120V Single Station Control —

3-position up-off-down switch permits op-

eration to be stopped at any point. Factory adjusted limit switches automatically

stop screen when fully down or fully up.

110-120V Multiple Station Control

—Switches are similar in appearance to 110-

120V Single Station Control. Screen stops when switch is released and may be

restarted in either direction. Factory adjusted limit switches stop screen auto-

matically when fully down or fully up.

24V Control —

Three-button up-stop-down switches stop at any point desired,

operate in any sequence. Factory adjusted limit switches automatically stop

screen when fully down or fully up.

Key Operated Switching —

Two kinds of key-operated switches are option-

ally available with this unit.

The key-operated power supply switch controls

power to the screen and switches. When it is “off”, the switches will not operate

screen. Key may be removed from the switch in either “on” or “off” position.

A three-position key switch permits the screen to be operated directly by key. In

this case, the screen’s operator must always have a key.

RS232/Ethernet—

Serial communication and network communication optionally

available.

Plug & Play

—

Provided with handheld IR remote control transmitter and 10'

(3m) cord. No wiring necessary except to connect to RS232. Screen is equipped

with a handheld remote or 3-position operating switch. Three positions (up-

off-down) permit operation to be stopped at any point. Factory adjusted limit

switches automatically stop screen when fully down or fully up.

Electrical Connections

Screen operates on 110-120V, 60 hz., 1.1 amp current draw. Duty cycle: On 28

seconds/Off 4 minutes.

Junction box is located inside left endcap and cover plate is secured to endcap

with two screws which may be removed with a Torx-head or small straight-blade

screwdriver. Junction box contains red, black and white pigtail leads and green

internal ground wire, per wiring diagram on reverse.

Screen is shipped with internal wiring complete and control switch(es) fully

boxed. Wire connecting screen to switch(es) and switch(es) to power supply

should be furnished by installer. Please Note: Screen must be installed in accor-

dance with the requirements of the Local Building Codes, the Canadian Electri-

cal Code (CEC), CAN/CSA C22.1 and the National Electric Code (NEC), NFPA

70. An appropriate disconnect device shall be provided as part of the building

installation.

Please Note: Do NOT wire motors in parallel.

All operating switches should be “off” before power is connected.

Plug-in power cord option available with built-in low voltage motor.

For Reconﬁguration/Conversion of Non-detachable Power Cord to

Field Wiring for Models TAR-28, TAR-29 and TAR-30 Only:

Disconnect cord plug from outlet.

Remove junction box cover.

Disconnect wire nuts from black, white and green wires.

Remove power cord and strain relief from screen.

Connect the black motor wire to "hot" supply wire.

Connect white motor wire to "neutral" supply wire.

Connect green/yellow wire to "ground" supply wire.

Replace junction box cover.

Ceiling Trim Kit

Optional - must be speciﬁed

Floating Mounting Bracket

Optional - must be speciﬁed

Ceiling Tile

(By others)

Screen

Case

Back

Trim Kit

Targa Electric Projection Screen

INSTRUCTIONS

INSTALLATION & OPERATION

If you have any difﬁculties installing or servicing your

projection screen, call your dealer or Draper, Inc.

Draper, Inc. | 411 S. Pearl St. Spiceland, IN 47385

draperinc.com | 765.987.7999 | 800.238.7999

CAUTION

Read instructions through completely before proceeding.

Follow instructions carefully. Installation contrary to instructions invalidates

warranty.

Screen should be accessible for complete removal should fabric become damaged

or should other service be required.

Screen should be installed level . The case must also (using a carpenter’s level)

be installed so that the top of the case is level (front-to-back) to prevent the fabric

from contacting the case housing.

Nothing should be fastened to screen dowel or viewing surface.

Operating switch(es) packed separately in screen carton.

Do not discard with packing material.

Screen operates on 110-120V, 60 hz. current.

Screen has been thoroughly inspected and tested at factory and

found to be operating properly prior to shipment.

These instructions are meant as a guide only.

They do not imply any responsibility on the part of the manufacturer

for improper installation or faulty workmanship at the jobsite.

Recessed Installation:

Recess should permit access for remov-

al of screen if necessary. Screen may be

mounted as in suspended or wall instal-

lation. Optional Ceiling Opening Trim Kit

available; see diagrams at right and on

page 3, and separate instruction sheet

(included with Ceiling Opening Trim Kit).

Please Note: Ceiling Opening Trim Kit

is for use in an acoustical, drop ceiling

only. Not recommended for drywall or

hard ceilings

Limit Adjustments (Built-in Low Voltage Motors)

Please Note: Screen limits are factory set for optimum performance

of the screen. Any adjustment of these limits could void the warranty.

Please check with Draper prior to resetting screen limits.

(Height adjustments are made from wall switch)

Connect the switch to the motor via the terminal blocks, or via the modular

port using four conductor modular cable. When using modular cable, the

cable connectors MUST NOT be crimped in reverse, as with standard

telephone cable.

Set the slide switch to the lower position. Press and hold the DOWN button

on the switch to move the viewing surface to the desired lower limit. If the

screen moves in the opposite direction, release the DOWN button and

press and hold down the STOP button for four seconds. This will reverse

the operation of the UP and DOWN switches.

Move slider switch into center position.Wait a couple of seconds.

Please Note: If you move the slider switch from down to up in one

motion it sets the two limits in the same position.

Set the slide switch to the higher position. Move the viewing surface to the

desired upper limit by pressing and holding the UP button on the wall

switch.

Return the slide switch to the center position to return to normal operation.

To set the viewing surface to an alternate format position, move the viewing

surface to the desired position and press the STOP button. Press and

hold STOP for at least three seconds to record the position.

Targa Electric Projection Screen Page 2 of 4

DOWN Limit

Counterclockwise

increases

down tr elav

UP Limit

Counterclockwise

increases

up tr elav POSITION FUNCTION

DOWN

CENTER

Set LOWER limit

Set UPPER limit

Normal Operation

To Motor

with

Built-In

Low Voltag

Slide

Switch

Back View of Wall Switch

To Motor

with

Built-In

Low Voltage

Please Note: 5V DC must be

connected to be able to set

limits using the wall switch.

Limit Adjustments (Standard Motors/Quiet Motors)

Please Note: Screen limits are factory set for optimum performance

of the screen. Any adjustment of these limits could void the warranty.

Please check with Draper prior to resetting screen limits.

(Height adjustments are made at the motor using white/yellow screws)

Tools needed: Flashlight, small ﬂathead screwdriver/Allen wrench (4mm or 5/32").

CAUTION: Always be prepared to shut screen off manually when new

adjustment is being tested. Screen may be severely damaged if

viewing surface is allowed to run too far up or too far down.

The motor limit screws are normally located on the audience left of screen

roller, and the viewing surface rolls off the back of the roller. If the viewing

surface is coming off the front of the roller (motor on left), or the motor is on the

audience right of the screen roller (with viewing surface rolling off the back),

reverse the following instructions.

"DOWN" LIMIT ADJUSTMENT

To Reduce Screen Drop

Raise screen surface about 1' above

desired setting and turn off.

Turn the DOWN limit screw clockwise

(three screw turns = ½ roller revolution).

Test by running screen down and repeat steps

1 and 2 until desired position is reached.

To Increase Screen Drop

Run screen to the down limit.

With the down switch on, turn the DOWN limit

screw counterclockwise (three turns of screw

equals ½ roller revolution)

to increase drop.

Test by running screen up about 1' and back down to new down limit.

Repeat steps 2 and 3 until desired position is reached.

"UP" LIMIT ADJUSTMENT

Screen is Running Too Far Up

Lower screen surface about 1' below desired setting and turn off.

Turn the UP limit screw clockwise (three screw turns = ½ roller revolution).

Test by running screen up.

Repeat steps 1 through 3 until desired position is reached.

Screen Needs to Run Up More

Run screen down about 1' and turn off.

With the up switch on, turn the UP limit screw counterclockwise

(three turns of screw equals ½ roller revolution).

Repeat steps 1 and 2 until desired position is reached.

CAUTION: Do NOT allow the dowel to wrap up over the roller when

the screen is running up! This could damage the screen.

Accessing Internal Low

Voltage Control Unit (LVC-IV)

To access the Internal LVC-IV:

Remove two (2)

Torx head

screws from

endcap

i L I

Remove access

panel with LVC IV

Electrical

Connection

Hole*

*A second electrical connection

hole is included in the screen

housing in order to separate Low

Voltage and High Voltage Wiring.

PLEASE NOTE:

Internal LVC-IV will increase

overall case length by 2".

Wiring Diagrams—110-120V Motor and Quiet Motor

with Internal Low Voltage Controller (LVC-IV)

Single Low Voltage Control

Internal Screen Wiring

White (Neutral)

Black

Green (Ground)

Dashed wiring

by electrician

To 110-120V Line

Multiple Low Voltage Controls

Internal Screen Wiring

White (Neutral)

Black

Green (Ground)

Dashed wiring

by electrician

To 110-120V Line

Wall Switch,

RF or IR

Receiver,

or integrated

control system

Wall Switch(es),

RF or IR

Receivers,

or integrated

control systems

Data Cable

(by others)

Data

Cable(s)

(by others)

Please Note: Pressing and re-

leasing the UP button on the switch

will move the screen to its upper

limit. Pressing and releasing the

DOWN button will move the screen

to its lower limit.

While the motor is in motion,

pressing STOP for less than two

seconds will stop the viewing sur-

face at its present position.

Once the motor is stopped,

pressing the STOP button will move

the viewing surface to its alternate

format position.

Pressing and holding the STOP

button, when the motor is at rest or

in motion, for at least three seconds

will record a new alternate format

position.

25/ "16

57/ "8

5¼"

7/ " dia.8

electrical

connection

hole

3½"

Viewing

Surface

Fabric width + 7"

Case Dimensions*

/ " hole r8fo

electr

ical

connection.

Fasteners rfo

wall mounting

by others.

S Hooks rfo

suspended

installation

by others.

6" Extension Bracket

Optional - must be speciﬁed

Targa Electric Projection Screen Page 3 of 4

Types of Installation

Appropriate hardware

provided installer.by

SuspendedWall

Appropriate hardware

provided installer.by

If using "S"

Hooks )by

others), be

sure to crimp

both ends

of the "S"

Hooks.

54mm

52m

102mm

171mm

27mm

203m

Ceiling Opening Trim Kit

Optional - must be speciﬁed

Ceiling Tile

(By others)

Screen

Case

Back

Trim Kit

Installation Methods

*PLEASE NOTE:

Internal LVC-IV will increase

overall case length by 2".

Product specificaties

Merk:	Draper
Categorie:	Projectiescherm
Model:	Targa
Kleur van het product:	Wit
Oorspronkelijke beeldverhouding:	16:9
Montagewijze:	Plafond
Aantal per verpakking:	1 stuk(s)
Ingangsspanning:	220 V
Gemakkelijk te installeren:	Ja
Zichtbare schermhoogte (h):	1320.8 mm
Zichtbare schermbreedte (b):	2336.8 mm
Diagonaal:	106 "
Type aandrijving:	Gemotoriseerd
Totale grootte van het scherm (hoogte x breedte):	162.56 x 243.84 cm
Spanscherm:	Nee