Draper Premier XL Handleiding
Draper
Projectiescherm
Premier XL
Lees hieronder de 📖 handleiding in het Nederlandse voor Draper Premier XL (8 pagina's) in de categorie Projectiescherm. Deze handleiding was nuttig voor 70 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/8
Overview - Components
CAUTION
Read and understand all warnings
(Page 2 of this document)
before beginning installation.
1.
Mounting holes
2.
Junction box cover
3.
Dowel
4.
Front cover
(Targa Pictured)
1
2
3
4
Contents
Overview - Components .......................................................................................1
Section 1 - Electrical Connections .....................................................................2
PLEASE READ - Safety Information ....................................................................2
Section 2 - Hanging Screen .................................................................................3
Section 3 - Operation............................................................................................3
Section 4 - Tab-Tension Adjustment Procedure ..............................................3
Section 5 - Limit Adjustments .............................................................................4
Section 6 - Dimensions and Methods of Installation ......................................5
Section 7 - Wiring Diagrams ................................................................................6
Section 8 - Wiring Diagrams ................................................................................7
Section 9 - Accessing Internal Low-Voltage Control Unit
(LVC-IV)
.................8
TOOLS
REQUIRED
POW R RILE D L
PENCIL
TAP ASUE E M RE
HAR ARDW E
(b oth rs)y e
L LEVE
Draper, Inc. | 411 S. Pearl St. Spiceland, IN 47385
draperinc.com | 765.987.7999 | 800.238.7999
© 2020 All Rights Reserved | FORM: Premier_XL_TargaXL_Inst20
Premier XL / Targa XL
Electric projection screen
INSTRUCTIONS
INSTALLATION & OPERATION
If you have any difficulties installing or servicing your
Premier XL / Targa XL, call your dealer or Draper, Inc.
Section 1 - Electrical Connections
Screen operates on 110-120V, 60 Hz. current. Screen ships with internal wiring complete
and control switch
(es)
fully boxed.
Wire to connect screen to switch
(es)
and switch
(es)
to power supply should be furnished
by installer.
Please Note: Screen must be installed in accordance with requirements of Local
Building Codes, Canadian Electrical Code
(CEC)
, CAN/CSA C22.1 and National
Electric Code
(NEC)
, NFPA 70. An appropriate disconnect device shall be provided as
part of building installation.
CAUTION: All operating switches should be "off" before power is connected.
PLEASE READ - Safety Information
FOR OPTIONAL PLUG AND PLAY:
Plug-in power cord option available for motor with internal
low-voltage controller. For reconfiguration/conversion of
non-detachable power cord to field wiring for models PRE-28,
PRE-29, TAR-28, and TAR-29 Only:
1.
Disconnect cord plug from outlet.
2.
Remove junction box cover.
3.
Disconnect wire nuts from black, white, and green wires.
4.
Remove power cord and strain relief from screen.
5.
Connect black motor wire to "hot" supply wire.
6.
Connect white motor wire to "neutral" supply wire.
7.
Connect green/yellow wire to "ground" supply wire.
8.
Replace junction box cover.
WARNING
Improper installation and use of the Premier XL / Targa XL screen can result in serious injury or death. Primarily, injuries can occur if the unit falls due to
imprecise installation, mishandling of the unit during installation, or installation on an insufficient wall or ceiling structure. Please use extreme care.
1.
Please read the following installation guidelines thoroughly and follow them
carefully. Failure to do so may cause product to fall or otherwise fail, and could
result in serious injury.
2.
Installation and calibration of the unit should only be performed by an
authorized, qualified, and experienced professional. In particular, electrical
work and wiring [indicated in diagram by dashed lines] must be completed only
by a qualified professional electrician who has read this manual completely
and is familiar with the construction and operation of this equipment and the
hazards involved.
3.
Do not affix the unit to walls or ceilings that have inadequate strength
to permanently hold the unit during use. It is the owner’s and installer’s
responsibility to confirm the wall or ceiling to which the unit attaches is
sufficient to permanently hold the weight and stress loads of the unit at all
times. Draper, Inc., is not responsible for improper installation, application,
testing, or workmanship related to the product at place of installation.
4.
It is the installer’s responsibility to make sure appropriate fasteners are used
for mounting.
5.
All hardware must be installed level. Unit must be level and square.
6.
Never leave the area while operating the unit during installation, maintenance,
or normal operation, unless it is secure and safe.
7.
Before testing or operation, carefully inspect the entire area and path
(especially
underneath)
of unit to be sure no persons or objects are in the area.
8.
Turn off power and any nearby equipment or cables carrying electricity before
connecting switches, wires, controls, or electrical components.
9.
Do not wire motors in parallel without written permission from Draper, Inc.
10.
During testing or operation, carefully watch the surrounding area for any
potential safety concerns including nearby persons or objects.
11.
After installation, the entire system, including all sensors, should be carefully
tested to ensure safe and normal operation. Extreme care should be taken
during testing to remain clear of moving parts to avoid possible injury.
12.
Operation of unit should be performed only by authorized and qualified
personnel, who have been trained in its safe and effective operation and
understand its safety features.
13.
The safety features of the unit should never be disabled, bypassed, or
overridden. The system should not be operated until all safety features are
properly and completely installed, calibrated, and tested.
14.
Unit may need to comply with local, state, or district rules and regulations, in
particular when installed in schools. All applicable rules and regulations should
be reviewed before installation and use.
15.
Failure to precisely follow installation guidelines invalidates all
warranties.
16.
Custom products/installations may not be reflected in this manual. Call Draper,
Inc., if you have questions about the installation of custom products or any
questions about your installation.
Before Beginning Installation
1.
Look for any job site conditions that could interfere with installation or
operation of the system.
2.
Read carefully and be sure to understand all installation instructions and
all related operations manuals. These instructions are intended to serve
as a guide for the installer and owner. They should be followed closely and
combined with the expertise of experienced qualified installers. Draper, Inc., is
not responsible for improper installation, application, testing, or workmanship
related to the product at place of installation. Please retain all instructions for
future use.
3.
Open cartons lengthwise.
4.
Locate and lay out all pieces.
5.
Inspect all boxes to make sure you have received the proper unit and parts.
Controls may be shipped separately, or in same carton as unit.
6.
If you have any difficulties with installing, servicing, or operating your unit, call
your dealer or Draper, Inc., 765-987-7999.
Important Safety Information Important Safety Information
page 2 of 8
Premier XL / Targa XL
Section 2 - Hanging Screen
Section 3 - Operation
Please Note: Before fully operating screen: For Targa, remove tape; on Premier, lower viewing surface enough to fully expose shipping brackets, then remove
shipping brackets by loosening screws, removing end shipping brackets, sliding center shipping brackets off dowel. Then, re-tighten screws
(Fig. 3)
.
General:
1.
Screen should be lifted into position only by end mounting brackets. Keep case level
by lifting end plates simultaneously to prevent surface damage. Never attempt to lift
screen along its length.
3.
When locating viewing surface and checking clearance for screen’s operation,
remember surface is centered in case. Handle case carefully to protect its finish.
4.
Regardless of mounting method, screen should be positively and securely supported
so that vibration or even abusive pulling on viewing surface will not cause case to loosen
or fall. Installer must ensure that fasteners used are of adequate strength and suitable for
mounting surface chosen.
Ceiling and Wall Installation:
CAUTION: Product is very heavy: Installer must provide adequate attachment hardware
and anchors as required. Installer must also ensure that structure is of adequate strength.
CAUTION: Case must be mounted low enough from ceiling to gain access to
bracket screws.
Please Note: Do not use a power screwdriver to tighten screw. Maximum torque for
tightening screw is 5 nm.
110-120V Single Station Control — 3-position up-off-down switch permits operation to be stopped at any point.
Factory adjusted limit switches automatically stop screen when fully down or fully up.
For LVC-IV Controls:
24V Control — Three-button up-stop-down switch
(es)
stop at any point desired, operate in any
sequence. Factory adjusted limit switches automatically stop screen when fully down or fully up.
1.
The key-operated power supply switch controls power to unit and switches. When it is “off”,
switches will not operate. Key may be removed from switch in either “on” or “off” position.
2.
A three-position key switch permits screen to be operated directly by key.
In this case, screen operator must always have a key.
RS232 / Ethernet — Serial communication and network communication available.
Plug & Play — Supplied with a 9'8"
(2.9m)
cable lead. No wiring is necessary.
Screen is equipped with a handheld remote or 3-position operating switch.
Three positions
(up-off-down)
permit operation to be stopped at any point.
Factory adjusted limit switches automatically stop screen when fully down or fully up.
Section 4 - Tab-Tension Adjustment Procedure
Please Note: The Draper Tab-Tensioning System is factory-set, and under
normal circumstances will not require field adjustment. If wrinkles are observed,
however, follow the adjustment procedure shown in Figure 4.
Figure 4
CAUTION: Do not remove the roller assembly from the case
unless necessary for repairs. If the roller assembly is removed,
be sure motor is fully re-seated in the bracket, and re-secure it
carefully with the motor retaining spring and screw.
PUSH & TURN
CLOCKWISE
to INCREASE TENSION
PUSH & TURN
COUNTER-CLOCKWISE
to RELEASE TENSION
END OF
DOWEL
END OF
DOWEL
Figure 3
Figure 2
MOTOR RETAINING
SPRING AND
SCREW
Motor Retaining
Screw
(included)
CAUTION: Do not touch or bend surface.
page 3 of 8
Premier XL / Targa XL
Product specificaties
| Merk: | Draper |
| Categorie: | Projectiescherm |
| Model: | Premier XL |
Heb je hulp nodig?
Als je hulp nodig hebt met Draper Premier XL stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Projectiescherm Draper
27 Mei 2023
28 April 2023
25 April 2023
24 April 2023
22 April 2023
19 April 2023
17 April 2023
13 April 2023
11 April 2023
11 April 2023
Handleiding Projectiescherm
- Projectiescherm Duronic
- Projectiescherm Elite
- Projectiescherm GPX
- Projectiescherm Kodak
- Projectiescherm Nec
- Projectiescherm Pyle
- Projectiescherm Vestel
- Projectiescherm Optoma
- Projectiescherm Oregon Scientific
- Projectiescherm Luxburg
- Projectiescherm Da-Lite
- Projectiescherm AV:link
- Projectiescherm Projecta
- Projectiescherm Elite Screens
- Projectiescherm EluneVision
- Projectiescherm Celexon
- Projectiescherm Lumene
- Projectiescherm Stewart
- Projectiescherm Avers
- Projectiescherm Instaal
- Projectiescherm Elite ProAV
- Projectiescherm KHOMO GEAR
- Projectiescherm EPV
Nieuwste handleidingen voor Projectiescherm
18 Augustus 2024
18 Augustus 2024
7 Augustus 2024
20 Juni 2024
20 Juni 2024
4 Mei 2024
4 Mei 2024
4 Mei 2024