Dolgin TC200 Two Position Handleiding

Dolgin Batterij-oplader TC200 Two Position

Lees hieronder de 📖 handleiding in het Nederlandse voor Dolgin TC200 Two Position (2 pagina's) in de categorie Batterij-oplader. Deze handleiding was nuttig voor 115 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
Battery Charger TC200
Owner’s Manual
 Dolgin Engineering 1019 Massachusetts Ave. Lexington, MA 02420 • (781) 863-1813 • www.dolgin.net
1
Introduction
The TC200 Battery Charger is electrically compatible with all 7.2V Li-Ion camera batteries rated 2200mAh or
higher. The modular design allows for different battery models to be charged when the appropriate adapter
plate is fitted. With the appropriate power cord, the charger can be powered by a 12V automobile power
source.
Standard Features
• Two simultaneous charge positions for fast charging of 2 batteries.
• Fast, safe, and reliable charging. The battery pack can be left on the charger after the charge is complete.
• Dynamic Power Management (DPM) minimizes battery charge time. By dynamically adjusting battery
charge current, more current is allocated to the deeper discharged of the two batteries. Through this
process both batteries are ready to use at about the same time.
• Wide range input power compatibility (100-240VAC 50-60Hz), 12V with the DC cigarette lighter cord.
• Compact, lightweight design for easy portability. Dimensions 5.5"x 4"x 1.5"
Batteries
The charger is capable of charging 2 batteries at the same time. It accepts Sony L/M (VX2xx or similar),
Panasonic DVX100/HVX200, AF100, Canon BPxx (XL/GL), and JVC BNVxx style batteries. The charger
must be configured with the appropriate plate to match the battery style.
The battery must to be rated at least 2200 mAh capacity, as smaller size battery packs are not designed to
accept the charger fast charge.
Charging time
The time to full charge depends on the battery pack rated capacity, its state of charge prior to insertion, and
its age. A fully discharged new 2200 mAh battery pack will be fully charged (more than 90%) in about 2.5
hours. A 5600 mAh pack will take approximately 3.5 - 4 hours to charge (4.5-5 hours when 2 batteries are
being charged). Since a depleted battery pack absorbs charge current faster than a partially charged one, most
of the charge energy is absorbed during the initial stage of charging and then the rate of charge levels off
towards the end.
Charge channels
Both charge channels are independent from each other; charge initiation and termination depend on a
battery’s state of charge. LEDs indicate each battery’s state of charge. Dynamic Power Management (DPM)
minimizes battery charge time. By dynamically adjusting battery charge current, more current is allocated to
the deeper discharged of the two batteries. Through this process both batteries are ready to use at about the
same time
Operation
Charging
Upon plugging the charger in into an electrical source the green and red LEDs will blink every 3 seconds to
indicate the charger is powered on. Insert a battery into the battery plate and the charger will initiate the
charge routine. While charging is in progress, the red LED will illuminate. Approaching charge completion,
the Green LED will blink at 90% readiness level, and will be steady ON on completion.
Status LEDs
1. Red ON Battery is inserted; charge in progress
2. Green blinking Battery is charged over 90% 3. Green ON Ready


Product specificaties

Merk: Dolgin
Categorie: Batterij-oplader
Model: TC200 Two Position

Heb je hulp nodig?

Als je hulp nodig hebt met Dolgin TC200 Two Position stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Batterij-oplader Dolgin

Handleiding Batterij-oplader

Nieuwste handleidingen voor Batterij-oplader