Doepfer A-176 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Doepfer A-176 (6 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 33 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/6
doepfer System A - 100 Control Voltage Source A-176
1
1. Introduction
Module A-176 (Control Voltage Source) provides
three voltage sources, to use wherever an extra CV
is required.
The top two voltage sources (CV 1 and CV 2) have
controls for coarse and fine control of the voltage
output; the third source (CV 3) just has the one control.
The range of the voltages output can be preset, either
to 0 to +5 V or to -2.5 V to +2.5 V depending on your
likely requirements. There is a jumper on the circuit
board for each of the three voltage sources.
A typical use for the module would be to provide fine
as well as coarse tuning for an A-110 standard VCO,
(which, unlike the A-111, only has one tune control),
See chapter 5, user examples.
In general, this module will be useful whenever you
need a manually controllable CV on a module which
doesn’t itself have a built-in control.
CV 3
Contr. Volt. Source
CV 1
Fine
CV 3
CV 1
CV 2
Fine
CV 2
A-176 Control Voltage Source System A - 100 doepfer
2
2. Overview Controls:
1 CV 1 : Coarse control for the voltage at
linked outputs ! and "
2 Fine : Fine control for the voltage at linked
outputs ! and "
3 CV 2 : Coarse control for the voltage at
linked outputs § and $
4 Fine : Fine control for the voltage at linked
outputs § and $
5 CV 3 : Control for the voltage at output %
Outputs:
! ", CV 1 : Parallel outputs for CV source one
§, $ CV 2 : Parallel outputs for CV source two
% CV 3 : Output for CV source three
CVS
CV 1
CV 1
Fine
Contr. Volt. Source
0 10
010
CV 2
CV 2
Fine
010
0 10
010
CV 3
CV 3
doepfer System A - 100 Control Voltage Source A-176
3
3. Controls
1 CV 1 • 3 CV 2
Controls 1 and 3 provide coarse adjustment of the
voltages at outputs ! and ", and § and $ respecti-
vely.
The range of controls 1 and 3 is approximately 5 V.
2 Fine4 Fine
Controls 2 and 4 provide precision adjustment of
control voltages CV 1 (at outputs ! and " ) and CV 2
(at outputs § and $) respectively.
The range of controls 2 and 4 is approximately 0.1 V.
5 CV 3
This knob sets the control voltage CV 3 , at output %.
The range of this control is approximately 5 V.
4. Outputs
! CV 1 • " CV 1
These are the internally connected parallel outputs
for the first CV source, whose level is set by controls
1 and 2.
§ CV 2 • $ CV 2
These are the internally connected parallel outputs
for the second CV source, whose level is set by
controls 3 and 4.
% CV 3
This is the output for the third CV source, whose
level is set by control 5.
H The voltage range for each of the sources
is individually adjustable with jumpers on the
circuit board, either to 0 V - 5 V or symmetri-
cal around zero (-2.5 V to +2.5 V).


Product specificaties

Merk: Doepfer
Categorie: Niet gecategoriseerd
Model: A-176

Heb je hulp nodig?

Als je hulp nodig hebt met Doepfer A-176 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Doepfer

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd