Dimplex GFP150W Handleiding

Dimplex Heater GFP150W

Lees hieronder de 📖 handleiding in het Nederlandse voor Dimplex GFP150W (4 pagina's) in de categorie Heater. Deze handleiding was nuttig voor 25 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

Installation and Operating Instructions

INDGUKP7RG Issue 0

Girona Panel Heaters

Dimensions

(millimetres)

Model(s) Watt A B

GFP050 W/B 0.5kW 530 107

GFP075 W/B 0.75kW 530 107

GFP100 W/B 1.0kW 700 107

GFP150 W/B 1.5kW 770 107

GFP200 W/B 2.0kW 940 107

Important Safety Advice

When using electrical appliances, basic precautions

should always be followed to reduce the risk of fire,

electrical shock, and injury to persons, including the

following:

IIMPORTANT – The wall bracket supplied with the

appliance must be used.

WARNING - DO NOT USE THIS HEATER IN THE IMMEDIATE

SURROUNDINGS OF A BATH, A SHOWER OR A SWIMMING

POOL.

IMPORTANT – If the heater is installed in a room

containing a bath or shower, it must be so installed that

switches and other controls cannot be touched by a

person using a bath or shower.

Do not use outdoors.

Do not locate the heater immediately below a fixed socket

outlet or connection box.

Do not cover the heater. Do not place material or

garments on the heater, or obstruct the air circulation

around the heater, for instance by curtains or furniture,

as this could cause overheating and a fire risk.

NEVER cover or obstruct in any way the heat outlet slots

at the top of the heater or the air inlet slots in the base of

the heater.

The heater carries the Warning symbol indicating

that it must not be covered.

WARNING – THE SURFACES OF THIS HEATER CAN BE HOT.

Momentary contact with any part of the heater should

not cause injury.

This appliance is not intended for use by persons

(including children) with reduced physical, sensory or

mental capabilities, or lack of experience and

knowledge, unless they have been given supervision or

instruction concerning use of the appliance by a person

responsible for their safety. Children should be

supervised to ensure that they do not play with the

appliance.

Note that due care and consideration must be taken

when using this heater in series with a thermal control,

a program controller, a timer or any other device that

switches on the heat automatically, since a fire risk

exists when the heater is accidentally covered or

displaced.

If the supply cord is damaged it must be replaced by the

manufacturer or service agent or a similarly qualified

person in order to avoid a hazard.

Fig. 1

IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE

Electrical

WARNING – THIS APPLIANCE MUST BE EARTHED

The electrical installation must be carried out by a competent

electrician, and be in strict accordance with the current I.E.E.

regulations for Electrical Equipment in Buildings.

The wires in this mains lead are coloured in accordance

with the following code :

GREEN AND YELLOW : EARTH

BLUE : NEUTRAL

BROWN : LIVE

BLACK : PILOT WIRE

- see also ‘Pilot Wire Connection’.

The heater is fitted with a length of flexible cable type H05VV-

F size 4 x 1.0mm2 for connection to the fixed wiring of the

premises through a suitable connection box positioned

adjacent to the heater.

The supply circuit to the heater must incorporate a double

pole isolating switch having a contact separation of at least

3mm.

Pilot Wire Connection

The BLACK control wire is designed to carry a signal from

slot in or wall mounted Dimplex programmers. If, however a

programmer is not being used, the pilot wire should be

isolated in accordance with the current IEE Wiring

Regulations.

IMPORTANT - DO NOT connect the BLACK pilot wire to earth.

Care should be taken with the installation of the pilot wire(s)

as when switching to background (set back) they become

energised at 240V although only at a current of less than

100mA. In every case a suitable means of isolation must be

provided for the pilot wire and marked to indicate that two

sources of supply may be present at the heater.

Where pilot wires are installed separately from the heater

final sub-circuit they should be protected, double insulated

and carry their own integral earth continuity conductor.

Supplementary Earth Bonding

Should Equipotential Earth Bonding be required the earthing

conductor in the supply cord is deemed to provide the

supplementary bonding connection (see Regulation 547-

03-05, 16th Edition I.E.E. Wiring Regulations).

565

B150

Min.

300 Min.

shelf

150 Min.

255 Min.

C D

GFP500 390 300

GFP750 390 300

GFP1000 560 300

GFP1500 630 300

GFP2000 800 300

‘x’

MAX

General

The heater is designed for wall mounting on the wall bracket

supplied. It should only be operated when in the upright

position - see Fig. 1.

All models are splashproof to IPX4 standard and may be

used in bathrooms, however not in the immediate vicinity of

baths, showers, water connections, wash basins or

swimming pools.

Before connecting the heater check that the supply voltage is

the same as that stated on the heater.

Wall Mounting

IMPORTANT – The wall bracket supplied with the appliance

must be used. The heater should be positioned observing

the minimum clearances stated around the heater - see

Fig. 1.

DO NOT locate the heater immediately below a fixed socket

outlet or connection box.

1. Remove wall mounting bracket from the back of the

heater by depressing the spring latch at the top of

each bracket - see Fig. 2.

2. Fix the wall bracket securely to the wall through the

four screw holes provided.

3. Present the heater to the wall bracket, and engage

lower slots in the back with bracket.

4. Raise the heater to upright position and push the

heater onto bracket to engage top latch.

Operation

Switching On the Heater (see Fig. 3)

The controls are located on the right hand side on top of the

appliance, lift flap to access the controls - see Fig. 3.

The button marked ‘ ’ controls the electricity supply to the

electronic thermostat. An indicator beside the ‘ ’ button

shows when the unit is powered ‘ON’.

Fig. 2

Fig. 3

Setting Desired Temperature (see Fig. 4)

The heater is fitted with an adjustable thermostat enabling

the room temperature to be controlled by adjusting the slider

accordingly. The min setting ‘ ’ represents a room

temperature of approximately 50C and may be used for

protection against frost. The ‘MAX’ setting represents a room

temperature of approximately 300C. The ‘ ’ symbol glows

when the elements are actually heating.

Turn on the heater using the ‘ ’ button and move the

thermostat slider to the desired position. When the room

temperature has reached the desired level, the power to the

elements will be reduced, the heater will then maintain the

room temperature at the chosen level.

NOTE - Should your heater fail to come on when the

thermostat slider is at a low setting, this may be due to the

room temperature being higher than the thermostat setting.

Background Temperature

When used in conjunction with a remote programming device

supporting a background/setback setting, the heater will

automatically operate at a room temperature setting of 5

less than the thermostat setting when the programme is in

background/setback mode.

Limiting the thermostat setting

Before wall mounting the product the installer may wish to

limit the heat selection slider movement for the operator.

This may be achieved by removing the two plastic pins (see

‘x’ in Fig. 5) from the rear of the thermostat moulding using

pliers and inserting them in the preferred holes to limit the

slider movement.

Fig. 5

Fig. 4

Notes to the Installer

Test Mode

When the heater is connected via a pilot wire system, the

test mode allows the installer to check whether the heater

is responding correctly to the incoming pilot wire signal.

Before switching the heater on at the mains, place the

thermostat slider in the ‘MAX’ position, then press and hold

the ‘ ’ button whilst switching on the mains.

The unit will now enter a test state for 4 mins. During this

test state the ‘ ’ neon will indicate the pilot wire status:

NEON PILOT WIRE

CONTROLLER MODE

Neon on - ON

Neon off - OFF

Neon flashing fast approx every 0.1sec - FROST

Neon flashing slow approx every 0.5 sec - SETBACK

Accessory Modules

Optional accessory modules are available for use with this

range of heaters - see separate User Instructions for details

on the operation of each accessory module.

Before fitting a control module switch the heater off at the

mains supply.

To insert a module, the plug-in protective cover on the right

hand side of the thermostat unit at the back of the heater

must first be removed.

Insert a flat-head screwdriver into the side of the cover and

prise away from the heater - see Fig. 6.

Lift the cover away from the heater to reveal the slide in

compartment.

Insert the accessory module into the slot ensuring it is

positively located in position - see Fig. 6.

Switch the heater on at the mains supply.

Fig. 6

Safety - Overheat protection

For your safety this appliance is fitted with a thermal cut-out.

In the event that the product overheats for some reason, the

cut-out prevents excessive temperatures on the product by

cutting the power to the heater. Once the heater has cooled

down, it will reset automatically, it will continue to cycle on

and off automatically until the reason for overheating is

removed.

Cleaning

WARNING – ALWAYS DISCONNECT FROM THE POWER

SUPPLY BEFORE CLEANING THE HEATER.

Before commencing cleaning, unplug the heater and allow it

to cool. Disconnect the electricity supply to the appliance.

The outside can be cleaned by wiping it over with a soft damp

cloth and then dried. Do not use abrasive cleaning powders

or furniture polish, as this can damage the surface finish.

To release heater from the wall bracket for cleaning or

redecoration, depress latch on both brackets (see Fig. 2)

and hinge forward.

Recycling

For electrical products sold within the European Community.

At the end of the electrical products useful life it

should not be disposed of with household waste.

Please recycle where facilities exist. Check with

your Local Authority or retailer for recycling advice

in your country.

After Sales Service

Your product is guaranteed for two years from the date of

purchase.

Within this period, we undertake to repair or exchange this

product free of charge provided it has been installed and

operated in accordance with these instructions.

Your rights under this guarantee are additional to your statutory

rights, which in turn are not affected by this guarantee.

Should you require after sales service you should contact

our customer services help desk on 0845 600 5111. It would

assist us if you can quote the model number, series, date of

purchase, and nature of the fault at the time of your call. The

customer services help desk will also be able to advise you

should you need to purchase any spares.

Please do not return a faulty product to us in the first instance

as this may result in loss or damage and delay in providing

you with a satisfactory service.

Please retain your receipt as proof of purchase.

Product specificaties

Merk:	Dimplex
Categorie:	Heater
Model:	GFP150W

Heb je hulp nodig?

Als je hulp nodig hebt met Dimplex GFP150W stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Heater Dimplex

Dimplex DTD4T Handleiding

15 November 2024

Dimplex DX 425E Handleiding

15 November 2024

Dimplex Mini Cube Handleiding

15 November 2024

Dimplex Huxley Revillusion HXY20-AU Handleiding

25 Maart 2024

Dimplex Strata Revillusion STA20-AU Handleiding

25 Maart 2024

Dimplex Sherwood Revillusion SWD20-AU Handleiding

25 Maart 2024

Dimplex SILVERTON Handleiding

26 Februari 2024

Dimplex MOCCA Handleiding

26 Februari 2024

Dimplex DHEBHT Handleiding

26 Februari 2024

Dimplex BK 1202 S Handleiding

26 Augustus 2023

Handleiding Heater

Nieuwste handleidingen voor Heater

Trisa 9330.44 Handleiding

18 December 2024

Hortus 211-413 Handleiding

18 December 2024

Yamazen HF-L122 Handleiding

18 December 2024

Yamazen HF-D121 Handleiding

18 December 2024

Yamazen HF-L121 Handleiding

18 December 2024

Universal Blue UCRA9104-24 Handleiding

18 December 2024

Orava VL-203 Handleiding

18 December 2024

SHX HL20OSZ Handleiding

16 December 2024

Stanley ST-125T-KFA-ES Handleiding

16 December 2024

Perel PHS2000 Handleiding

14 December 2024