Dimplex DXLWP400 Handleiding

Dimplex Heater DXLWP400

Lees hieronder de 📖 handleiding in het Nederlandse voor Dimplex DXLWP400 (4 pagina's) in de categorie Heater. Deze handleiding was nuttig voor 32 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

Important Safety Advice

When using electrical appliances, basic

precautions should always be followed to

reduce the risk of ﬁ re, electrical shock, and

injury to persons, including the following:

IMPORTANT – The wall bracket supplied with

the appliance must be used.

WARNING – DO NOT USE THIS HEATER

IN THE IMMEDIATE SURROUNDINGS OF A

BATH, A SHOWER OR A SWIMMING POOL.

IMPORTANT – If the heater is installed in a

room containing a bath or shower, it must be so

installed that switches and other controls cannot

be touched by a person using a bath or shower.

Do not use outdoors.

Do not locate the heater immediately below a

ﬁ xed socket outlet or connection box.

WARNING: In order to avoid overheating, do

not cover the heater. Do not place material

or garments on the heater, or obstruct the

air circulation around the heater, for instance

by curtains or furniture, as this could cause

overheating and a ﬁ re risk.

NEVER cover or obstruct in any way the heat

outlet slots at the top of the heater or the air

inlet slots in the base of the heater.

The heater carries the Warning symbol

indicating that it must not be covered.

CAUTION - Some parts of this product can

become very hot and cause burns. Particular

attention has to be given where children and

vulnerable people are present.

This appliance can be used by children aged

from 8 years and above and by persons with

reduced physical, sensory or mental capabilities

or lack of experience and knowledge if they

have been given supervision or instruction

concerning use of the appliance in a safe way

and understand the hazards involved.

Dimplex Low Wattage Panel Heaters

Models: DXLWP400, DXLWP400TI,

DXLWP800, DXLWP800TI N & ARLWP800TI

Installation and Operating Instructions

Dimensions

(millimetres)

Models Speciﬁ cation

DXLWP400 400W Neon Heat Switch

DXLWP400TI 400W Neon Heat Switch / 24 Hour Timer

DXLWP800 800W Neon Heat Switch

DXLWP800TI N 800W Neon Heat Switch / 24 Hour Timer

ARLWP800TI 800W 2 Neon Heat Switches / 24 Hour Timer

THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE

600 mm - 400W

800 mm - 800W

500 mm

INDUKLWPRG Issue 9

Children shall not play with the appliance.

Cleaning and user maintenance shall not be

made by children without supervision.

Children of less than 3 years should be kept

away unless continuously supervised.

Children aged from 3 years and less than 8

years shall only switch on/oﬀ the appliance

provided that it has been placed or installed in

its intended normal operating position and they

have been given supervision or instruction

concerning use of the appliance in a safe way

and understand the hazards involved. Children

aged from 3 years and less than 8 years shall

not plug in, regulate and clean the appliance

or perform user maintenance.

Note that due care and consideration must be

taken when using this heater in series with a

thermal control, a program controller, a timer

or any other device that switches on the heat

automatically, since a ﬁ re risk exists when the

heater is accidentally covered or displaced.

If the supply cord is damaged it must be

replaced by the manufacturer or service agent

or a similarly qualiﬁ ed person in order to avoid

a hazard.

WARNING: Servicing and product

repairs should only be undertaken by the

manufacturers approved service agent or a

similarly qualiﬁ ed person, using only exact

manufacturer approved spare parts.

Installation

The Fixing Kit should contain: 1 Drilling Template, 3 Screws, 3

Rawlplugs and 1 Mounting Bracket.

Wall Mounted Operation Fig. 2(see )

Suggested Fixings

SOLID BRICK/BLOCK: No. 8 Rawlplug inserts, 6mm drill bit.

PLASTERBOARD: If possible locate studding and use No. 8

woodscrews directly into the wood, otherwise M5 rawlplug intersets

are suitable.

NOTE: FOR OTHER WALL TYPES (e.g. Timber frame and hollow

concrete) SEEK SPECIALIST ADVICE.

1. Select the position for the heater ensuring there is clearance

from any furniture and ﬁ ttings of at least 150mm above the

heater, 50mm below and 25mm each side. Curtains must

not be closer than 150mm from the top of theheater.

2. Position the drilling template provided on the wall ensuring

it is level. Mark the position of the relevant holes on the

wall at the edge of template. Before drilling check that the

distance between the hole centres is correct, 340mm for

400W Models and 540mm for 800W models (see ).Fig. 2

Fig. 2

Positioning the Heater

Select the position for the heater ensuring there is clearance from

any furniture and ﬁ ttings of at least 150mm above the heater, 50mm

below (wall mounted) and 25mm each side. Curtains must not be

closer than 150mm from the top of the heater.

Free Standing Operation Fig. 1(see )

NEVER USE THE HEATER FREE STANDING WITHOUT THE

FEET FITTED (FEET ARE PACKED SEPARATELY IN CARTON).

1. Lay the heater on its front.

2. Remove the two star head screws from the base of the

heater using a x-head screwdriver.

3. Place feet over base of heater, align holes and engage hook

on foot into the recess on the back of the heater - see Fig.

4. Replace the screws but do not overtighten.

Fig. 1

Rear View

3. Drill the wall at the three marked positions and ﬁ t the wall

plugs.

Ensure template has been removed.

4. Fix two No. 8 screws to the top two holes leaving 3mm of

the screw exposed. Hang the heater on the screws.

5. Fit the bottom bracket, found in the ﬁ xing kit, in the slot at

the base of the heater and screw the bracket to the wall.

Test that the heater is now securely ﬁ xed to the wall.

130mm 340mm - 400W

540mm - 800W

95mm

150mm

50mm

420mm

25mm 25mm

130mm

Drilling Holes

Bracket

Electrical Connection

WARNING THIS APPLIANCE MUST BE EARTHED

If the socket outlets in your home are not of the 13 amp BS1363

type they will not accept the plug connected to this heater,

therefore cut oﬀ the plug. When cut off this plug can constitute

a shock hazard if inserted into a socket outlet. It must therefore

be disposed of safely.

Before wiring the appropriate plug please note that the wires in this

mains lead are coloured in accordance with the following code.

GREEN/YELLOW: EARTH

BLUE: NEUTRAL

BROWN: LIVE

Connect the Green/Yellow E wire to the terminal marked or the

earth symbol or coloured or Green Green/Yellow.

Connect the wire to the terminal marked or coloured Brown L Red.

Connect the wire to the terminal marked or coloured Blue N Black.

DO NOT connect the Brown (Live Blue) or the (Neutral) wires

to the terminal of your 13 amp plug. If the terminals of the Earth

plug are unmarked or you are in any doubt, consult a qualiﬁ ed

electrician.

CAUTION: If you use this heater in conjunction with a thermal

control, programme controller, timer or any other device which

switches the heater on automatically observe all safety warnings

at all times.

Models with Timer

DXLWP400TI, DXLWP800TI N & ARLWP800TI

Set the I

- - sliO

de switch on the timer

( ) to:Fig. 3

Position O - Heating Oﬀ

Position I - Manual operation

This setting allows power to the heater

uninterrupted by the timer settings. The

heat selector switch will control the output

(see ‘Using the heater’).

Position - ‘Auto’ operation

DO NOT disconnect this heater from the

mains supply unless it is being taken out

of use (e.g. in summer or for storage),

otherwise the timer clock will stop.

Setting the time of day

To set the time of day, rotate the timer dial

clockwise (indicated by the arrow) until

the correct time of day is opposite the

reference mark (see ). Fig. 4

The 24-hour clock is used: e.g. time shown for 3 pm is ‘15’

(15:00hrs).

Setting the ‘Auto’ ON and OFF times

To set the timer:

1. Using your ﬁ nger tip or the tip of a

pencil, push in as many segments as

necessary around the dial, according to

the times you don’t require heat – see

Fig. 4. Each segment pushed in switches

the heater OFF for that part of the hour.

All other segments will be ON. For

example, Fig. 5 shows the timer set to

switch the heater ON between 7 am and

9 am and between 4 pm and 9.30 pm .

2. You can select as many ON periods as you like, within the

24-hour day. The settings will repeat every day until changed.

3. To change ON and OFF times, simply push in any ‘ON’ segments

you wish to cancel and pull out new ‘ON’ segments as required.

Switching to auto

Set the heat selector and thermostat for the heat output required.

Check that the clock shows the correct time of day. Set the I - 

- O slide switch to  (see Fig. 4) - the convector will switch ON

and OFF according to the timer settings (see Fig 5).

IMPORTANT NOTES

Remember to observe all safety warnings when operating the

heater on auto setting unattended or attended.

If the mains supply to the heater is interrupted, the timer clock

will stop until power is restored; reset the time of day to ensure

correct ON and OFF times.

Operation

IMPORTANT - OBJECTS OR CLOTHING MUST NOT BE

PLACED ON THIS HEATER.

Before using the heater ensure that all warnings and

instructions have been read carefully.

OPERATION - SINGLE RATED MODELS

Models DXLWP400, DXLWP400TI, DXLWP800, and DXLWP800TI

Turn the heater on using the switch on the right side of the heater

- the switch will be illuminated.

OPERATION - DUAL RATED MODEL - Model ARLWP800TI

The two switches on the side of the heater control the heat output.

Both switches illuminated indicates maximum output.

Top switch only illuminated indicates 500W output on 800W

model.

Bottom switch only illuminated indicates 300W output on 800W

model.

Note: on models ﬁ tted with a timer, at least one switch must be

illuminated for the heater to operate.

MODELS WITH TIMER - Fig. 3 (see )

DXLWP400TI and DXLWP800TI N - 1 Switch,

The switch on the side of the heater turns the heater on.

Note: This switch must be in the “on” position before the heater

will operate.

ARLWP800TI - 2 Switches

The two switches on the side of the heater control the amount

of heat available as described above, (Operation - Dual Rated

Model).

NOTE: At least one switch must be in the ‘On’ position before the

heater will operate.

4.00 pm - 9.30 pm

7.00 am - 9.00 am

Fig. 3

Fig. 5

Fig. 4

Product specificaties

Merk:	Dimplex
Categorie:	Heater
Model:	DXLWP400
Kleur van het product:	Wit
Gewicht:	4600 g
Breedte:	600 mm
Diepte:	200 mm
Hoogte:	530 mm
Soort:	Radiator
Aan/uitschakelaar:	Ja
Oververhittingsbeveiliging:	Ja
Verwarmingsvermogen:	400 W
Plaatsingsopties:	Wall,Floor
Verwarming power (min):	- W