Digitus DA-90384 Handleiding

Digitus Niet gecategoriseerd DA-90384

Lees hieronder de 📖 handleiding in het Nederlandse voor Digitus DA-90384 (5 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 53 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/5

A. Operating Control Panel

EN EN

Timer Timer

Memory/Screen lock (unlock) Memory/Screen lock (unlock)

Downward movement Downward movement

Upward movement Upward movement

Memory 1/2/3 Memory 1/2/3

Display Display

Operation Instruction:

1. When the system is powered on, you will hear a beep and the existing desktop

height will be displayed on the controller.

2. Upward movement

Downward movement

Touch the “ ” or “ ” and do not release until the desk reaches the desired height. If

the motor continuously operates for a relatively long period of time, the overheat

protection will activate. The control panel will work normally again after approximately

20 minutes.

3. Memory Mode

To store a certain height in the controller’s memory, first touch “ ”. The letter “ ” will

be displayed. Now touch “ ”, “ ”, or “ ” within five seconds to store the current height in

memory. The “ ”, “ ”, or “ ” buttons can each store a different height. Once in memory,

you can select any of the 3 height settings found in the controller’s memory by

pressing the corresponding button. Touching any buttons (except for “ ”) will stop the

automatic adjustment.

4. Reset Mode

While the unit is powered on, press the “ ” button until the desk moves into a fully

lowered position, “63.0” or “73.0” is displayed on the controller. Again, press the “ ”

button until “RST” is displayed on the controller. Once the display shows

“62.0” or “72.5”, release the “ ” button-the desk will move upward for approximately

10mm or 5mm and automatically come to a stop. After finishing the reset, the

controller should display “63.0” or “73.0” which is the current height.

5. Time Reminder

To set the time reminder, press “ ” found on the controller. The display will flash “0.5h”

which means 0.5 hour. Press the “ ” repetitively to increase 0.5 hours at a time. The

maximum timer setting is two hours. The timer is set when the digit stops flashing and

the light in the top right corner of the controller is on. When the timer has reached the

set time, the buzzer beeps, reminding the user to adjust his/her working position.

Once a timer setting has expired, the unit’s timer is cancelled. To de-activate the timer,

press the “ ” five times until the current height is displayed and the light found in the

upper right side of the controller is off.

6. Protective Standby Mode (60 Second)

If you want to prevent accidental operation, long press “ ” button for 3s to activate

standby mode. The protective standby mode activates when the display shows “---”.

The protective standby mode will also activate when there is no operation over 60s.

To turn off the standby mode, long press the “ ” button for 3s.

7. Power-saving Mode (10 Minutes)

When no actions are made for over 10 minutes, the system will enter power-saving

mode. Touch any button to enter operation mode.

8. Switch measurement between cm and inch

The preset measurement shown on the display is cm. If you would like to change cm

to inch, please restart the system and press the button “ ” for 8 seconds. After the

buzzer beeps twice, the measurement is successfully reset. If you would like to switch

inch back to cm, please restart the system and press the button “ ” for 8 seconds.

After the buzzer beeps once, the system is successfully switched to cm measurement

again.

Trouble Shooting

Below are the possible error codes that may be displayed on the control panel.

Error Code Description

ER1 Overload in downwards direction has occurred and needs to be

restart power.

ER2 Over-heating in the controller has occurred and needs to cool.

ER3 Motor cable connection fault and needs to be reset.

ER4 Both legs have different heights and need to be reset.

ER5 Motor fault

Note:

1. Self-protection function: the unit will enter protective mode if the system operate in

excess of two minutes with “HOT” on the controller display. The system will reset

and return to normal operation after approximately 18 minutes.

2. Overload protection mode: while operating, if the load on the desk is over weight

capacity, the system will enter into an overload protection mode. This will protect

the system from damages caused by exceeding weight. When this happens, the

desk will move downward approximately 30mm and come to a stop with the

current height displayed.

3. Attention: NEVER remove or turn off the power in order to reset the unit when it is

in a protective mode or “HOT” state.

4. Please reset in case two legs are different in height.

Product specificaties

Merk:	Digitus
Categorie:	Niet gecategoriseerd
Model:	DA-90384
Gewicht:	30600 g
Diepte:	700 mm
In hoogte verstelbaar:	Ja
Maximale gewichtscapaciteit:	100 kg
Frame kleur:	Zwart
Aantal benen/poten:	2 poot/poten
Maximum breedte:	1000 mm
Type hoogteverstelling:	Electrisch
Minimale hoogte:	630 mm
Maximale hoogte:	1250 mm
Compatibele breedte bureaublad (max):	2000 mm
Compatibele diepte van bureaublad (min):	700 mm
Compatibele diepte van bureaublad (max):	900 mm