Digimerge Echelon DCB44DL Handleiding

Digimerge Bewakingscamera Echelon DCB44DL

Lees hieronder de 📖 handleiding in het Nederlandse voor Digimerge Echelon DCB44DL (2 pagina's) in de categorie Bewakingscamera. Deze handleiding was nuttig voor 52 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
Product Information
User Manuals
Quick Start Guides
Specificatio Sheets
Software Upgrades
Firmware Upgrades
VISIT
www.digimerge.com
Digimerge Technologies Inc.
Copyright © 2011 Digimerge Technologies Inc.
As our products are subject to continuous improvement,
Digimerge reserves the right to modify product design,
specifications and prices, without notice and without
incurring any obligation. E&OE
IT’S ALL ON THE WEB!
Camera Specifications
ULTRA RESOLUTION
VARIFOCAL IR
BULLET CAMERA
Specfications:
1/3" Sony Super HAD™ II
Video Output
Horizontal Resolution
Termination
Lens Focal Length / Type
S/N Ratio
Power Consumption
NTSC: 768 (H) x 494 (V)
600 TVL
2.8-12mm F1.4 / Varifocal
> 50dB (AGC off)
Internal; 2:1 Interlace
75ft (23m); 30 LED's
Operating Temp. -4°F ~ 122°F
Comp. 1.0 Vpp @ 75ohm
Iris & Shutter Speed AES; 1/60 ~ 1/100,000 sec.
Power Requirement
Dimensions
Minimum Illumination
Video Format / Pixels
0.2 LUX @ F2.0 (IR Off)
0 LUX (IR LEDs ON)
0.9kg / 1.9lbs
Height: 85mm / 3.4
Width: 137mm / 5.4”
Length: 255mm / 10.1”
Weight
Sync. & Scan. Systems
IR Range
Image Sensor
DCB34DL - 12V DC ±10%
DCB44DL- 12V DC/
24V AC ±10%
Video: BNC Female
DCB34DL - 350 mA
DCB44DL - 12V - 500 MA
24V - 330 mA
FOV (Horizontal) 25 - 88 degrees
Dimensions:
137mm / 5.4”
255mm/ 10.1”
85mm
3.4”
DCB34DL (12V)
English Version 2.0
QUICK START GUIDE
Copyright © 2011 Digimerge Technology Inc.
www.digimerge.com
DCB44DL (12/24V)
MODEL:
1. Connect the BNC connector of the camera to the
video cable.
2. DC Power
Power adapto
r: Connect a 12V DC
Power Adaptor (not included) to the camera. Plug
the Power Adaptor into a local power outlet.
DC Power—
Power Pigtail
(not included):
Connect a Power Pigtail to the camera. Connect
the terminating wires of the cable directly to the
DC power source.
NOTE: The Power Pigtail is a non-polarity input.You can connect the
wires to either the positive or negative ports of the DC power source.
• :DCB44DL ONLY
AC Power:
Connect
a Power Pigtail
(not included)
to the camera. Connect the terminating wires of
the cable directly to the 24V AC power source.
NOTE: If the onscreen display is blurry, you may need to
set the Monitor Impedence switch to 75 ohms.
3. Adjust the ZOOM and FOCUS knobs as required.
NOTE: If the ZOOM and FOCUS knobs are too tight for
adjustment, use a philips screw driver to slightly
loosen the screws on the knobs.
ZOOM / FOCUS knobs
Screw
Contents Installing the camera
1 x Weatherproof IR Bullet
Camera with Varifocal Lens
1. Use the included mounting template to mark
mounting points.
2. Loosen the fastening screw at camera base using
the small allen key.
3. Rotate the camera base counter clockwise to
separate it from the camera stand.
4. Mount the camera base to the wall using the
included screws.
NOTE: This camera is not intended for ceiling mounting.
If you mount the camera to a ceiling, the camera will
have to point downwards for adequate clearance.
5. Loosen the camera stand screws. using the large
allen key.
6. Feed the BNC/power termination cable through
the camera base. Connect video and power cable
as described in next section 'Setting up the
camera'.
7. Screw the camera clockwise onto the camera
base. Do not tighten all the way.
8. Move the camera to the desired position and while
holding it firmly in place, turn the adjustment ring
on the camera stand clockwise to tighten. Next,
tighten the two screws on the camera stand.
Fastening Screw
Adjustment ring
Camera base
Camera stand screws
Features
Sony Super HAD™ II / 600TVL
Advanced Digital Noise Reduction (DNR)*
75 ft (23m) IR Night Vision Range**
2.8 - 12mm Varifocal Lens
External Zoom/Focus adjustment
IP66 Weatherproof rating***
Cable Through bracket Design
*Default Setting
** IR Illumination range under ideal conditions. Objects at or beyond this
range may be partially or completely obscured, depending on the camera
application.
*** Not recommended for submersion in water
WARNING - A REGULATED UL/CSA APPROVED 12V DC / 24V AC power
supply is REQUIRED for use with this camera. Use of a non-regulated,
non-conforming power supply can damage this product and will void
the warranty.
4 x Mounting screws
Setting up the camera
ATTENTION - Test the camera prior to selecting a permanent
mounting location by temporarily connecting the cameras and
cables to the DVR or Observation System.
PRECAUTIONS
Use an appropriate low voltage power cable to prevent fire or
electrical shock.
Make sure to install the camera in an area that can support the
camera weight.
There are no user serviceable parts inside the camera. Please
do not disassemble the camera.
Do not clean the lens cover with an abbrasive cleaning material
Please use a soft cloth to clean the lens cover.
1x Mounting Template
1 x Small Allen Key
1 x Large Allen Key


Product specificaties

Merk: Digimerge
Categorie: Bewakingscamera
Model: Echelon DCB44DL

Heb je hulp nodig?

Als je hulp nodig hebt met Digimerge Echelon DCB44DL stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Bewakingscamera Digimerge

Handleiding Bewakingscamera

Nieuwste handleidingen voor Bewakingscamera