Delta Dore Tyxia 4860 Handleiding

Delta Dore Receiver Tyxia 4860

Lees hieronder de 📖 handleiding in het Nederlandse voor Delta Dore Tyxia 4860 (1 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 38 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/1
1 - Installation
The TYXIA 4860 is designed to control (On/Off or Dimming) LED lights on the
DALI bus.
The DALI dimmer module can be installed either in a ush-mount housing
behind a push button or behind a ceiling.
You can control the module via a wireless X3D transmitter
or the TYDOM application.
Use an electrically insulated tool
to work on the dimmer module button.
2 - Connection
L
L
N
N
230 V
1
L
N
2
20 max.
ca. DC 14V
2
2
1
1
A
B
C
230V~
2 VA
1 2
TYXIA
4860
D A L I
35270 - Bonnemain - FR
LNCDADA N
12345
20 devices
40 mA Max.
A Disconnected wires must be insulated (domino).
B IMPORTANT: the control wires are not insulated from the mains power
supply. All connected equipment must be marked CE and meet the require-
ments of the low voltage devices as well as assembly recommendations.
Local control wires can be extended up to 10m (insulate from 230V).
C Do not switch on before connecting the load.
3 - Association
Ê Switch on the system. Press and hold the dimmer module button for 3 seconds
until its LED ashes. Release.
Ë On the transmitter, send the association command (see user guide).
- Make sure that the dimmer module LED has stopped ashing.
The products are now associated.
1
230V
ON
TYDOM
A
B
COM
IN1
IN2
CR 2032
TYXIA
2600
> 3s
A B
> 3s
2
... ...
> 3s
4 - Operation
4.1 Simple push-button
You have 2 modes to choose from:
• . On/Off + dimming from 0% to 100% with storage of the latest Mode 1
intermediary level. (by default).
- When the lighting is off:
Briey press the control button to switch the lighting to the stored level.
After releasing:
- A short press under 5 seconds switches the lighting level to 100%.
- Pressing and holding before 5 seconds increases the lighting.
- A short press after 5 seconds switches the lighting level to 0%.
- Pressing and holding after 5 seconds dims the lighting.
- When the lighting is on:
- A short press switches the lighting level to 0%.
- Pressing and holding dims the lighting. Release.
Pressing and holding again before 5 seconds dims the lighting, after 5
seconds, the lighting increases.
• . On/Off + dimming from 0% to 100% without storage of the Mode 2
intermediary level.
- When the lighting is off:
- A short press changes the lighting level from 0% to 100%.
- Pressing and holding increases the lighting.
- When the lighting is on:
- A short press switches the lighting level to 0%.
- Pressing and holding dims the lighting. Release.
Pressing and holding again before 5 seconds dims the lighting,
after 5 seconds, the lighting increases.
4.2 Double push-button
4.3 Simple/Double push-button
- Storage of the intermediary level:
Hold down the push button until the required level:
the lighting intensity varies. Release when the required level is reached.
The intermediary level is stored
4.4 To change to a different operating mode:
- Hold down the receiver button for 6 seconds.
- After 3 seconds, the LED ashes slowly.
- After 6 seconds, the LED is on without ashing. Release.
- Press the button briey to toggle between modes.
Mode 1 Mode 2: 1 ash, : 2 ashes.
Validation of the mode:
- Press the receiver button for 3 seconds until the LED stops ashing.
5 - Help
List of functions accessible using the dimmer module button:
3’’ 6’’>
A
>10’’ 20’’ 30’’> >
D E
>
CB
AAssociation
Press the button for 3 seconds until the LED ashes. Release
BMode 1/ Mode2 conguration
Hold down the button for 6 seconds.
- After 3 seconds, the LED ashes slowly.
- After 6 seconds, the LED is on without ashing. Release.
- Press the button briey to toggle between modes.
(Mode 1: Flashes once - Mode 2: Flashes twice).
- Press the button for 3 seconds to conrm.
CRemove an association
Ê Hold down the button for 10 seconds:
- After 3 seconds, the LED ashes slowly.
- After 6 seconds, the LED is on without ashing.
- After 10 seconds, the LED will blink fast. Release.
Ë Conrm on the transmitter (refer to the user guide).
- Make sure that the dimmer module LED has stopped ashing.
The products are no longer associated.
1 2
> 3s
> 10s
DRemove all associations
Hold down the button for 20 seconds:
- After 3 seconds, the LED ashes slowly.
- After 6 seconds, the LED is on without ashing.
- After 10 seconds, the LED will blink fast.
- Press and hold the button until the LED goes out. Release.
> 20s
OFF
EFactory reset
Hold down the button for 30 seconds:
- The LED ashes, then goes off.
- The dimmer module is blank and the wireless link and operating mode
are reset (mode 1 by default).
Example
EN
EN DALI dimmer module
Green
White
Yellow
Button
LED
Remove an
association Remove all
associations
Factory
reset
Association
Not connected
1
2
Technical characteristics
- Power supply: 230 V~ 2 VA
- Number of serially-connected ballasts: 20 maximum
- Maximum output power: 40mA,
equivalent to 20 ballasts of 2mA each
- Number of associated transmitters: 16 maximum
- Storage temperature: -10°C/+70°C
- Operating temperature: -10°C/+40°C
- IP 40 (ush mounting box)
- Dimensions: 50 x 47 x 23 mm
- X3D wireless remote control device:
868.7 MHz to 869.2 MHz
- Maximum wireless power < 10mW
- Category 2 receiver
Conguration
Mode 1/Mode 2
www.deltadore.com
TYXIA 4860 - DALI
Button 2
Press once briey: OFF
Press and hold:
Dimming down
Button 1
Press once briey: ON
Press and hold:
Dimming up


Product specificaties

Merk: Delta Dore
Categorie: Receiver
Model: Tyxia 4860

Heb je hulp nodig?

Als je hulp nodig hebt met Delta Dore Tyxia 4860 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Receiver Delta Dore

Handleiding Receiver

Nieuwste handleidingen voor Receiver