DBX Zone Pro 1260 Handleiding

DBX Staafmixer Zone Pro 1260

Lees hieronder de 📖 handleiding in het Nederlandse voor DBX Zone Pro 1260 (75 pagina's) in de categorie Staafmixer. Deze handleiding was nuttig voor 54 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/75
User Manual
1 2 6 0 / 1 2 6 1
WARNING FOR YOUR PROTECTION
READ THESE INSTRUCTIONS:
KEEP THESE INSTRUCTIONS
HEED ALL WARNINGS
FOLLOW ALL INSTRUCTIONS
DO NOT USE THIS APPARATUS NEAR WATER
CLEAN ONLY WITH A DRY CLOTH.
DO NOT BLOCK ANY OF THE VENTILATION OPENINGS. INSTALL IN ACCORDANCE WITH
THE MANUFACTURER’S INSTRUCTIONS.
DO NOT INSTALL NEAR ANY HEAT SOURCES SUCH AS RADIATORS, HEAT REGISTERS,
STOVES, OR OTHER APPARATUS (INCLUDING AMPLIFIERS) THAT PRODUCE HEAT.
ONLY USE ATTACHMENTS/ACCESSORIES SPECIFIED BY THE MANUFACTURER.
UNPLUG THIS APPARATUS DURING LIGHTNING STORMS OR WHEN UNUSED FOR LONG
PERIODS OF TIME.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polar-
ized plug has two blades with one wider than the other. A grounding type plug has
two blades and a third grounding prong. The wide blade or third prong are pro-
vided for your safety. If the provided plug does not fit your outlet, consult an elec-
trician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at plugs, con-
venience receptacles, and the point where they exit from the apparatus.
Use only with the cart stand, tripod bracket, or table specified by the manufacture,
or sold with the apparatus. When a cart is used, use caution when moving the
cart/apparatus combination to avoid injury from tip-over.
Refer all servicing to to qualified service personnel. Servicing is required when
the apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the appa-
ratus has been exposed to rain or moisture, does not operate normally, or has been
dropped.
POWER ON/OFF SWITCH: For products provided with a power switch, the power
switch DOES NOT break the connection from the mains.
MAINS DISCONNECT: The plug shall remain readily operable. For rack-mount or
installation where plug is not accessible, an all-pole mains switch with a contact
separation of at least 3 mm in each pole shall be incorporated into the electrical
installation of the rack or building.
FOR UNITS EQUIPPED WITH EXTERNALLY ACCESSIBLE FUSE RECEPTACLE: Replace fuse
with same type and rating only.
MULTIPLE-INPUT VOLTAGE: This equipment may require the use of a different line
cord, attachment plug, or both, depending on the available power source at instal-
lation. Connect this equipment only to the power source indicated on the equipment
rear panel. To reduce the risk of fire or electric shock, refer servicing to qualified
service personnel or equivalent.
This Equipment is intended for rack mount use only.
SAFETY INSTRUCTIONS
NOTICE FOR CUSTOMERS IF YOUR UNIT IS EQUIPPED
WITH A POWER CORD.
W .A R N I N G : T H I S A P P L I A N C E M U S T B E E A RT H E D
CONNECT ONLY TO A MAINS SOCKET OUTLET WITH
PROTECTIVE EARTHING CONNECTION.
The cores in the mains lead are coloured in accordance with
the following code:
GREEN and Y E L L OW - Earth BLUE - Neutral BROWN - Live
As colours of the cores in the mains lead of this appliance may
not correspond with the coloured markings identifying the ter-
minals in your plug, pr ws:oceed as follo
• -The core which is coloured green and yellow must be con
nected to the terminal in the plug marked with the letter E,o r
with the earth symbol, or coloured gre e n , or green and ye l l o w.
• The core which is coloured blue must be connected to the
terminal marked N or coloured black.
• oThe core which is coloured br wn must be connected to the
terminal marked L or coloured red.
This equipment may require the use of a different line cord,
attachment plug, or both, depending on the available power
source at installation. If the attachment plug needs to be
changed, refer servicing to qualified service personnel who
should refer to the table below. een/yThe gr ellow wire shall be
connected directly to the units chassis.
WARNING: If the ground is defeated, certain fault conditions in
the unit or in the system to which it is connected can result in
full line voltage between chassis and earth ground. Severe injury
or death can then result if the chassis and earth ground are
touched simultaneously.
The symbols shown above are internationally accepted
symbols that warn of potential hazards with electrical
pr ro -oducts. The lightning flash with ar wpoint in an equi
lateral triangle means that there are dangerous voltages
pr -esent within the unit. The exclamation point in an equi
lateral triangle indicates that it is necessary for the user to
refer to the owner’s manual.
These symbols warn that there are no user serviceable
parts inside the unit. Do not open the unit. Do not
attempt to service the unit yourself. Refer all servicing to
qualified personnel. Opening the chassis for any reason
will void the manufacturer’s warranty. Do not get the unit
wet. yIf liquid is spilled on the unit, shut it off immediatel
and take it to a dealer for service. Disconnect the unit
during storms to prevent damage.
IMPORTANT SAFETY INSTRUCTIONS
U.K. MAINS PLUG WARNING
A molded mains plug that has been cut off from the cord is unsafe.
Discard the mains plug at a suitable disposal facility. NEVER UNDER
ANY CIRCUMSTANCES SHOULD YOU INSERT A DAMAGED OR CUT
MAINS PLUG INTO A 13 AMP POWER SOCKET. Do not use the
mains plug without the fuse cover in place. Replacement fuse covers
can be obtained from your local retailer. Replacement fuses are 13
amps and MUST be ASTA approved
to BS1362.
IMPORTANT SAFETY INSTRUCTIONS
ELECTROMAGNETIC
COMPATIBILITY
This unit conforms to the Pro d u c t
Specifications noted on the Declaration
of Conformity. Operation is subject to
the following two conditions:
• this device may not cause harmful
interference, and
• this device must accept any interfer-
ence received, erenceincluding interf
that may cause undesired operation.
Operation of this unit within significant
electromagnetic fields should be avoided.
• use only shielded interc o n n e c t i n g
cables.
DECLARATION OF
DECLARATION OF
DECLARATION OF
DECLARATION OFDECLARATION OF
CONFORMITY
CONFORMITY
CONFORMITY
CONFORMITYCONFORMITY
Manufacturer’s Name: dbx Professional Products
Manufacturer’s Address: 8760 S. Sandy Parkway
Sandy, USAUtah 84070,
declares that the product:
Product name: dbx 1260 and dbx 1261
Note: Product name may be suffixed by the letters-EU.
Product option: None
conforms to the following Product Specifications:
Safety: IEC 60065 (1998)
EMC: EN 55013 (1990)
EN 55020 (1991)
Supplementar ormation:y Inf
The product herewith complies with the requirements of the
Low Voltage Directiv ectivee 73/23/EEC and the EMC Dir
89/336/EEC as amended by Directive 93/68/EEC.
Vice-President of Engineering – Pro
8760 S. Sandy Parkway
Sandy, USAUtah 84070,
Date: 2004August 23,
European Contact: Your local dbx Sales and Service Office or
Harman Music Group
8760 South Sandy Parkway
Sandy, USAUtah 84070,
Ph: (801) 566-8800
Fax: (801) 568-7583

Product specificaties

Merk: DBX
Categorie: Staafmixer
Model: Zone Pro 1260

Heb je hulp nodig?

Als je hulp nodig hebt met DBX Zone Pro 1260 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Staafmixer DBX

DBX

DBX Zone Pro 1260 Handleiding

15 April 2023

Handleiding Staafmixer

Nieuwste handleidingen voor Staafmixer

Electroline

Electroline ELNEXTSTANDMIX389G Handleiding

18 November 2024
Princess

Princess 221229 Handleiding

16 November 2024
Zelmer

Zelmer ZHB4640 Handleiding

14 November 2024
Sunbeam

Sunbeam Zumbo SM9600 Handleiding

13 November 2024
Morphy Richards

Morphy Richards MRHBS8BK Handleiding

13 November 2024
KitchenAid

KitchenAid KHMB732 Handleiding

11 November 2024
KitchenAid

KitchenAid KHM7210 Handleiding

11 November 2024
Comelec

Comelec BA 1171 Handleiding

11 November 2024
Cuisinart

Cuisinart Power Advantage HM-C Handleiding

23 Oktober 2024
Hyundai

Hyundai HM 707 Handleiding

21 September 2024