Da-Lite Tensioned Executive Electrol Handleiding
Da-Lite
Projectiescherm
Tensioned Executive Electrol
Lees hieronder de 📖 handleiding in het Nederlandse voor Da-Lite Tensioned Executive Electrol (8 pagina's) in de categorie Projectiescherm. Deze handleiding was nuttig voor 8 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/8
INSTRUCTION BOOK FOR
Tensioned Conference Electrol
2
NOTE: Unit is not to be installed in air handling spaces.
1. The case brackets provide multiple attachment points for bolts,
cables, or threaded rod. The following page shows two locations
for typical threaded rod installations with the external case
mounting brackets (Figure 1a) and without them (Figure 1b). The
internal case brackets can be accessed through the hand holes
(Figure 1c).
2. The case has a self-trimming lange around the bottom. Ceiling
tiles or drywall may be placed on top of this lange to provide a
inished appearance.
3. After securing the case in the ceiling, check that the case is level
and plumb.
4. Use supplied 1/8” nex key and a 1/4” wrench to remove silver
shipping brackets attached to slat and screen case.
5. Install electrical connections that apply to your unit. Refer to the
electrical diagram on page 4. The electrical connections are
accessible by removing the two screws on the primary junction
box cover and the two screws on the secondary low voltage
cover (Figure 2). You can remove the access door if needed to
allow for greater access to the electrical wiring. To remove the
access door; remove the screw from each end of the door while
holding the door and slide the door of the langes (Figure 3).
NOTE: Must be installed in accordance with the requirements of
the Local Building Codes, the Canadian Electrical Code (CEC),
CAN/CSA C22.1 and the National Electric Code (NEC), NFPA 70.
Installation
Important Safety Instructions
When using your video equipment, basic safety precautions
should always be followed, including the following:
1. Read and understand all instructions before using.
2. To reduce the risk of electric shock, do not disassemble this
appliance. Contact an authorized service dealer when repair
work is required. Incorrect reassembly can cause electric shock
when the appliance is used subsequently.
3. The use of an accessory attachment not recommended by the
manufacturer may cause a risk of ire, electric shock, or injury to
persons.
4. Do NOT lift or push up on the camera arm mechanism at any
time. This may cause improper operation and/or component
failure or injury to persons.
Save These Instructions
Pre-Installation
1. Carefully unpack screen and remove outer wrapping from case.
2. Make sure to recheck measurements of screen location
before installation.
Hand Hole
Internal
Bracket
Figure 1a – Threaded Rod with Internal Bracket
Figure 1b – Threaded Rod with Internal and External Bracket
Figure 1c – Internal Bracket
Hand Hole
Hand Hole
3
6. Remove shipping brackets by removing the hex head screws
from aluminum slat and case. Slat should move freely (Figure 2).
(Only if the roller assembly is pre installed.)
7. Test installation by operating the screen several times. Be
prepared to stop the screen. Standard Duty Cycle: 1MIN. ON/3
MIN. OFF. The fabric door (rear door) will not close until the wall
switch is placed in the up position and when the screen motor
stops at its limit switch in the up direction.
CAUTION: Excessive continuous operation may cause the
motor to overheat. If this happens the motor will shut of
until it cools to a normal operating temperature.
ATTENTION! Le fonctionnement continu et excessif peut
provoquer une surchaufe.Si cela se produit, les moteurs
s'arrêteront jusqu'à qu'ils se soient refroidis à la température
normale de fonctionnement.
8. Run the screen down enough to open the fabric door. Insert
the access door on the langes and reinstall the screws to
secure the door.
Installation (continued
Figure 2 – Bottom of Case Figure 3 – Bottom of Case
Shipping Bracket
Secondary Low
Voltage Cover
Primary Junction Box Cover
Access Door
Door Screw Door Screw
Product specificaties
| Merk: | Da-Lite |
| Categorie: | Projectiescherm |
| Model: | Tensioned Executive Electrol |
Heb je hulp nodig?
Als je hulp nodig hebt met Da-Lite Tensioned Executive Electrol stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Projectiescherm Da-Lite
7 Augustus 2024
24 Juni 2023
4 Juni 2023
31 Mei 2023
30 Mei 2023
25 Mei 2023
21 Mei 2023
Handleiding Projectiescherm
- Projectiescherm Duronic
- Projectiescherm Elite
- Projectiescherm GPX
- Projectiescherm Kodak
- Projectiescherm Nec
- Projectiescherm Pyle
- Projectiescherm Vestel
- Projectiescherm Optoma
- Projectiescherm Oregon Scientific
- Projectiescherm Luxburg
- Projectiescherm Draper
- Projectiescherm AV:link
- Projectiescherm Projecta
- Projectiescherm Elite Screens
- Projectiescherm EluneVision
- Projectiescherm Celexon
- Projectiescherm Lumene
- Projectiescherm Stewart
- Projectiescherm Avers
- Projectiescherm Instaal
- Projectiescherm Elite ProAV
- Projectiescherm KHOMO GEAR
- Projectiescherm EPV
Nieuwste handleidingen voor Projectiescherm
18 Augustus 2024
18 Augustus 2024
20 Juni 2024
20 Juni 2024
4 Mei 2024
4 Mei 2024
4 Mei 2024
4 Mei 2024